What do you think of the Mini 4 Pro? Get the most out of it with my DJI Cheat Sheets and Luts - dmprovisuals.com

@davelawrence594

19 күн бұрын

Is this your very own website!!

@waldtradition1166

3 күн бұрын

I have quite a few drones from DJI, love them and have mostly good experiences with them, but my experience with Mini4 Pro lasted for about 15 min. Everybody said how well and great the active track worked, so after flying for about 14 min I tried it out, It was about 1 min in the air before it crashed into a substantial tree fell to the floor and broke. So I mailed DJI gave them my reports and told them that I did not fly the drone but AI did it, so they should take care of the incident. Well they came back to me, quite helpful in a way and told me sorry but it was pilot error, even though I did not fly the drone.

Your first point is KEY! I film boats, while on boats, moving at up to 50mph. I could never figure out why there isn’t a “return to controller” feature. That would save me the constant heart attacks if I lose sight of the drone for a second, while doing 50mph! 😮😅

@DMProductions

20 күн бұрын

exactly this !

@ChrisMitchells_FlyingCameras

20 күн бұрын

RTH to the controller might seem like a good idea but then some dufus would activate RTH to the controller and the drone would hit them on the head as it descends to land. Lawsuit. It’s really not a good idea.

@ThroughTheCamerasEye

20 күн бұрын

@@ChrisMitchells_FlyingCameras valid point. Sadly. But the rest of us shouldn’t suffer because of that one ding-dong. Let’s just trust in Darwin.

@gregorpesek

19 күн бұрын

@@ChrisMitchells_FlyingCameras There are drone licenses required for a reason. No one goes out on the street buying a car without or even with a license and crashes into a pole and sues the pole. If someone is that dumb they them self get put into the prison/gets a fine for not knowing how to operate basic human inventions. Not a valid point at all.. If you didn't read T&C that's your own fault. In T&C it clearly states that you are required to learn all the basic rules of flying a drone and following the local regulations which state, you should be aware of the drones position / keep it in line of sight at all time and always make sure for a safe landing. It's the pilot responsibility for all that

@hagnbike

19 күн бұрын

@@ChrisMitchells_FlyingCameras That thing has crash control on all sides. Return to Controller could also mean one meter in front of the controller. Or, it could mean hover at 2meters over the controller so it can be grabbed.

DJI will never make a perfect drone as who would buy the next one. Protecting themsleves by small improvments

@clarkjamesdigital

20 күн бұрын

this, and they also intentionally withhold features and mess things up, so that they can sell it in the next version, they give us just enough for it be worthwhile, where as competitors do everything they can to make a perfect product but are unfortunately hampered by inferior tech, oh and dont get me started on how in this world of symbiotic relationships between brands and content creators the game is to slowly 'fix' the product with firmware updates over the lifetime of the product cycle to garner constant news headlines

@clarkjamesdigital

20 күн бұрын

dji market the RC2 as having external antenna for better signal and totally ignore how they're fragile and also quite annoying to have to fold out, and at the same time they market the DJI FPV remote 3 as having no external antenna so it's more convenient and quicker to deploy... it's so absurd

@ChrisMitchells_FlyingCameras

20 күн бұрын

It’s no different than any other tech company. Shouldn’t be looked at as a negative, just reality.

@midlifeadventuretravels

20 күн бұрын

This is the case for all companies who are at the cutting edge of innovation, as consumers we have to realise it and if you’re an early adopter like me you have to recognise companies will exploit your weakness for the latest thing, and your susceptibility to influencers - like this channel (with the greatest respect Darren as I do value your videos). Anyway, having bought the mini 4 Even though I had the mini 3 I do utilise those next steps and incremental benefits and will probably buy the mini five as soon as it comes out. in the meantime, I will await the arrival of my M4 iPad Pro and the latest version of Final Cut pro for iPad to edit all the lovely footage from my latest DJI drone no matter what they are withholding. 🤣🤣 life will be simpler and cheaper if I wasn’t an early adopter 🤣🤣🤣🤣

@markj.a351

19 күн бұрын

Every tech company does this for products at this price point. Just don’t be a brainless consumer. If the value proposition isn’t good enough for you then just upgrade every few generations.

For flying in rain or moisture I will place masking tape or any tape covering the USB and SD slots. No big issue, it might be a couple of times a year…..

@DMProductions

20 күн бұрын

problem with that if the tape falls off and get stuck on the rear propellors it won't end well...

@ExHanseat

19 күн бұрын

@@DMProductions Use 3M tape. Before that gets off, the drone has to be shot out of the sky with a pump gun.

@MyFriendlyPup

19 күн бұрын

Medical tape wont come off

Another really helpful video. I am still getting to grips with my Mini 4 but so far it it an impressive piece of kit. Your channel is a wealth of information. Cheers mate

Is it possible to configure one of the RC2 buttons on the back to set/update Home Point, so one click and it's updated?

Hi there Darren first thing Great KZread channel I have a DJI mini 2 and definitely would like to upgrade to a DJI pro 4... just a quick question would it be better to wait for the DJI pro 5 which will be out sometime this year... or just get the DJI pro 4 done...? Cheers Rob 👍

So would you recommend the Mini 3 Pro with the RC1.

With the ports, how about tape? With the propellers, how does the gaurds affect it?

Hey Darren thanks for sharing. RC2 is super sluggish too since last update. Thank you again for the video and highlighting certain issues the M4P.

@DMProductions

19 күн бұрын

Thank you !

Some valid points about the RTH opportunity

@DMProductions

20 күн бұрын

Thanks Eddie but did you like the Simpson cameo 😂

Do you still rate the dji mini pro 3 flymore with rc, and do you know of anywhere it's still in stock?

I will be getting a mini 4 pro next month which is an upgrade from my mini 1 will check back over your videos to get the best settings.

Your reviews are quite something else fella your indepth reviews are brilliant!!👌🏻👍🏻

@DMProductions

19 күн бұрын

Thank you I appreciate that

I'm new to drones and looking to buy my first one but can't decide which one to get . What would you suggest for an absolute beginner ? Is the Mini 4 Pro worth the extra over the Mini 3 Pro as I won't be using all the camera capabilities.

My biggest gripe is the frame of the body - it's so thin to keep the weight down while packing in all the tech so it's so thin and makes this creaking/cracking sound when handled!

Excellent video and all points mentioned.. I trashed the screwdriver, bought a proper one. My favourite feature, hands down, is cruise control. Using this feature only I'm getting about 18 minutes out of the batteries. Mini 4 Pro is all I need at the minute.

@DMProductions

19 күн бұрын

Cruise control is such an underrated feature love it

I have the mini 4 pro with the RC2 controller and my issue is when sometimes flying the screen toggles back to the go fly screen without touching it

Definitely the combo deal with extra batteries. I bought another two: with 5 I can go off into the hills and have never run out yet.With RTH I thought you were going say just to cancel RTH and just land it wherever you are.

Correct I saw that when I tested!

What about the LEDs remain on whilst in video mode?

Excellent video love this drone but I do agree with you

@DMProductions

20 күн бұрын

Thanks 👍

I completely agree with everything you said there. Surely firmware updates can fix them.

@DMProductions

19 күн бұрын

I'm sure they can too

Hey! The DJI fly App not working on my Pixel 7 phone, do you have any idea how to Fix it?

Did my second flight today, the footage is very impressive, hope to see those software updates . The music sponsor sounds good, I just ordered the LUT'S and cheat sheets. Cheers!

@DMProductions

20 күн бұрын

Thank you ! Glad you're liking the drone !

Great Vid man. What have u heard about the Nxt air, as far as when it's expected ? Thanks!

@DMProductions

20 күн бұрын

Not sure yet still loving the Air 3

@ipadmini1874

20 күн бұрын

​@@DMProductionsFor sure man. I'm asking bc I'm getting it if the other one isn't coming out in a few months.

@DMProductions

19 күн бұрын

@@ipadmini1874 yeah nothing mentioned about it currently

@ipadmini1874

19 күн бұрын

@DMProductions cool man. I'm getting it.

I think the way the props are mounted is ok, admittedly not as convenient as on the air series but just changing to Torx screws would improve things no end.

why they don't sell the bigger batteries for the moni 4 pro ? other drones are over 250g so what's the point

Great video! Should I get a DJI OSMO POCKET 3 or a MINI 4 PRO?

@DMProductions

19 күн бұрын

tough one depends which one you'll use most

@Kobro10

19 күн бұрын

@@DMProductions which one do you use most?

Great video! I am new to your channel and just subscribed. I just purchased the Mini 4 Pro. I also own the Spark and the OG Mavic Pro. Had my first flight today with the Mini 4 Pro. Went well. Very nice drone. However, post flight I found that I could not load the photos onto my Apple products. Wondering if there is a setting that would allow Apple products to see photos on SD card. I did not have this problem with my other DJI drones. Thanks in advance!

Are those super expensive DJI care package worth it? do people ever use it? I'm getting into the drone thing soon & just need to know what to & not to buy with it.

I agree that you should buy the fly more kit to get the three batteries - but also buy one more battery so there is always one in the drone. 👍🏻 Also buy the Philips 000 screw driver you’ll never regret that purchase.

Great points Darren. Still quite happy with my Mini 3 Pro Fly More at the current time. Got my annual DJI refresh cover coming up plus my Operators ID is due again, so have stuff to sort while waiting for the rain to stop 👍

@Voltis-5

18 күн бұрын

Can you add more to the DJI refresh after it expired? Mine M3P is going on 2 years and I think it's about to expire.

@terryneilbooth

18 күн бұрын

@@Voltis-5 Mine is only the 12 months plan. DJI tend to send you reminders to renew a few weeks before it is due for renewal.

Thanks for such an indepth analysis. I am about to buy my first drone and would you recommend below 250gm ones? Does Parrot or any non-China brand still sells any below 250gm?

@DMProductions

19 күн бұрын

for under 250g nothing comes close to these DJI Mini drones , any of them

@paybacktime2625

14 күн бұрын

@@DMProductions Thanks! My trust ion Made in China brand has never gone smooth. I researched and found same that in terms of feature nothing matches DJI but those loopholes mentioned are crazy. Hope Anafi comes up with mini drones.

The Mini 4 Pro in EU refuses to fly with the non-branded DJI Plus battery? Is the a fix?

HI there. One point on the Mini 4 propellers and the screwdriver. I went and got a higher quality one at a hardware store. It is very easy to strip these screws if you do not get the screwdriver in the screw exactly right.

@DMProductions

19 күн бұрын

great point!

Does anyone know if you can set this drone so that photos/videos etc you capture save to the RC controller SD card rather than the drone SD card 🤔 (or as well as) thanks in advance.

@olabergvall3154

20 күн бұрын

I believe you can turn on video caching, which will save to RC2, but it will only be 1080p

Great video Darren. You’re right about that diddy screwdriver. What a nuisance it is. Being disabled I prefer the push/twist propellers. I have to get someone to change mine with the screwdriver. Hope you are well. Take care ❤

@DMProductions

20 күн бұрын

the push/twist propellers are indeed so much better! I have no idea why they can't add these unless its down to weight but doesn't make sense...

@wallygargett6175

20 күн бұрын

@@DMProductions I also do find the controller very slow getting up to speed. I’m sitting waiting for everything to come on the controller. It never used to be like that. ❤️👍

I might have to wait to get this one when its cheaper because the newer one comes out

I totally agree with you when it comes to return to home .. It should update the home point automatically when the controller changes position. And there should be covers on the card slot and the USBC port. All that being said though this drone is so much fun to fly.

@DMProductions

19 күн бұрын

it sure is and it can only get better!

Definitely, love the Mini 4 Pro. I personally think that the active track sucks for the terrain where I use it, unfortunately. Better than the Mini 3, though.

The controller does not have GPS .. the UAV does so how can the mini track the controller anyway ?

Great video

mini 2 fly more combo owner since new. beside the battery depleting a bit quicker then the 25 mins flight per but I have 3.

New to drones. Mini 4 pro my 1st ever, thanks to this channel's candor. I'd like instruction without reading the manual - call me lazy:) I was trying to land in a tight spot but OA wouldn't let me. EZ way to override when want to manually land?

@DMProductions

18 күн бұрын

Yeah turn sensors off

hey, once again a great, informative video. The disadvantages of the hardware that you mentioned (i.e. props, non-watertight openings, etc.) cannot be corrected or only on future versions. On the other hand, I really hope that DJI will hear your voice and offer appropriate updates, as well as the one about the completely unsuccessful update for the RC2 ! (which I didn't do after your warning in the video!). Another solution that I use for the batteries and that might also be interesting for other users: Thanks to the combo, I have a total of 3 batteries. I also bought a FASTCHARGE ANKER 24,000mAh. As soon as the first battery dies, I fastcharge it immediately. By the time I've flown and drained the other two batteries, the first one is full again. Very efficient and practical.

@DMProductions

19 күн бұрын

yes Anker make some really good fast chargers ! Very good choice

Awesome video Darren, your right with what you said about update home point, not very ideal when you are cycling, by the way are you going to be uploading some vegas videos soon, from the NAB event, im asuming you are, it looked an amazing event

@DMProductions

19 күн бұрын

Yes lots more on way buddy!

@aaphotofilm

19 күн бұрын

@@DMProductions can’t wait. That sphere in vegas is a must see. I need to see that when I’m there lol

Great video !

@DMProductions

20 күн бұрын

Glad you enjoyed it

With my M3P the included screwdriver was worthless. If I’d kept trying to remove the screw from the prop the screw would’ve been stripped. I bought an inexpensive micro drive set that had the proper screw head.

Considering buying this as my first drone. The controller kind of concerns me, it was one of the primary attractions to the drone. I appreciate the heads up on the batteries and will get the fly more. Everything else is okay for me

@DMProductions

19 күн бұрын

Once the controller is switched and the drone is in the air it fine, its just the start up time has been increased but great drone

Just have to have “return to controller” to solve rth problem when you are moving

One issue you have to mention is the network connectivity. Some times I get signal loss for 600 to 800 mtrs.

RTH should always be the controller, or there should be a shortcut button enabled to update the RTH to controller. It is quite easy to land the drone in the palm of your hand.

The mini 3 Pro has that one tiny screwdriver. I had to use it when I crashed into trees in follow mode (my stupid fault trying to hide the Rc😢). Static electricity causes the screws to move around. Attach the new screws (supplied) to the driver and into the props. Only then place the props onto the drone arm. Worked for me. Then I went online and bought a bigger 000 driver.

@DMProductions

19 күн бұрын

yes the 000 driver is much better but lets hope for push in props next time

I love my mini 3pro. I use it more than I use my air 3…which is an amazing quad! But the mini 3pro is just so great.

Be ok if, while your in tracking mode that you could press c1 or c2 to be able to update home point rather than pulling down and scrolling to find update home point.

@DMProductions

18 күн бұрын

Yes absolutely

Great video! I've seen enough to know that I'll be passing on this model. Like the Mavic, this seems like more problems than it's worth.

Isn't the home point issue the same on all DJI consumer drones? I don't think it is so much a Mini 4 issue, as it is a DJI drone issue. But I strongly agree with you about the props, DJI please get rid of the screw on props, and save the extra weight of the twist on props somewhere else. Great video Darren, and thanks for sharing.

Avata 2 or DJI mini 4 pro??????

As a first time user of drones i noticed all these points you made, im really hoping im able to attach a Mavic 4 pro later to the RC2. i really want to see camera swaps to these i wanted the triple lens mavic but i was afraid i would crash my first drone immediately so i went with the latest most affordable version.

@DMProductions

19 күн бұрын

yes future mavic drones should 100% support OC4

This is my favorite drone, but after recent updates I've noticed erratic flight in Normal or P mode. When flying forward the Mini 4 will regulate its speed causing erratic flight. This is with obstacle detection off. It's like someone getting on and off the gas.

I always wonderd why the remotecontroller itself is not the return to home unit automaticly

And the subject scanner Why do we need to turn it on with every flight Just leave it how I set it And the 360 wheel how do you use it when it’s so small My fat fingers can not get it to work But in some of the how to videos it appears to be a larger icon With no explanation of how to get it larger

Excellent video

@DMProductions

19 күн бұрын

Thank you very much!

I broke a prop on my Mini 4 Pro and absolutely could not get one of the screws undone with the supplied screwdriver. The screws have a thread locking compound on them which makes some of them almost impossible to undo without rounding out the head. My advice would be to buy a decent Phillips 000 screwdriver from Wiha or another good toolmaker and then heat up the screwdriver before use to soften the locking compound. I had to send my Mini 4 Pro back to DJI to get one of the props removed as both screws heads rounded out. Always use the new screws supplied when you’re replacing the props as they have fresh thread locker on them. Shit design tbh and very frustrating when compared to the simplicity of the Air 3.

I'm a drone pilot sinds the Spark. Much longer than that I'm an RC-plane pilot. With the Spark I could customise the control sticks in the way that pulling the stick is going up and pushing is down, same as with common (RC-) planes. The Mini 4 Pro offers several customisation settings for the control sticks, however, no option for pulling is up and pushing is down. As a drone- and RC-plane pilot it is very tricky to fly these types of aircraft with reversed up-down stick setting. Here too, DJI should offer an upgrade to the Spark feature.

Thanks for sharing... that's why I stick with dji mini 3 pro... regards from Denmark 👍

i have the rc2 and the rc pro and i much prefer the rc pro because it's quicker, can install 3rd party apps and feels more premium in the hand. the rc2 feels cheap imho.

I often fly from moving boats. The lack of a simple way to update homepoint is driving me mad, and I've had so many near losses because of it. It doesn't take more than somebody disturbing me for a short while and the drone is halfway to a spot where it intends to land on water.

My RC2 has a bunch of bugs, it is May 2024, not fixed, the RC2 boots up, the screen is backlit, after the boot-up, the backlight is gone. Newest FW...

The charging port and card holder are quite easy to cover with a piece of tape.

Other than return to home, it’s all due to the weight limit enforced by regulation. Still, a great informative video summarize everything a buyer should know. Personally I decided to upgrade to the Air 3 and I’m much happier. But for people who cannot exceed 249g this is still the best choice.

Hi Darren, Thanks for Highlighting THE MOST Infuriating Flaw in the M4Pro's Firmware, ie, the Fundamentally Flawed RTH Function when Tracking! So if DJI gives the operator the facility to have the Drone Follow them in or on a Vehicle, do they expect them to just drive around in a Big Circle so as not to get out of range of the original homepoint? I just can't see the point of having this facility when it fails the moment the Operator sets off in one distinct direction! When the RTH kicked in my first reaction was to Cancel it, but then I kept getting Onscreen messages that my Battery will explode if I don't RTH Right Now!.. So, I had to Stop everything and Land the drone there and then. So next time I will be prepared, But there doesn't seem to be an easy way to manually update the homepoint in the App? You have to go through the Safety options until you eventually reach the 'Update Homepoint' screen, which when everything at that moment is time critical, it just seems counter intuitive which goes against everything DJI has stood for thus far! I haven't attempted to use the Tracking Function since! I really can't see the Reasoning behind DJI's decision to omit an absolutely necessary Safety Function in Tracking Mode.

@DMProductions Great review Bro!! I might have to skip that firmware update, and wait for the next one. “World’s smallest screwdriver” 😂😂😂 I think there may be smaller ones, but definitely agree with you on keeping it all in your bag. That’s why for everyone watching I highly recommend getting the Fly More combo if it can be afforded

Very valid criticism and DJI should take action‼️

I just purchased the 4 pro About a month ago It does have some great features But I had to go find it yesterday As it was following me through a canyon as I was getting close to 30 percent battery I knew of a nice flat spot just ahead of me but by the time I got there I was 28 percent and the return home feature was activated I tried to stop it and get the drone to come to me but the low battery and return feature kept popping up I was not sure of the drone’s exact location and there were several large rock formations in between us so I pointed the camera down and picked a clear spot and put it down Ok it landed but were Turns out about 600 meters around a big bin in the canyon I can tell you the find my drone feature works As I walked to it the dots got closer and closer until I saw it setting their waiting with the camera still on With that said Would not a come to the controller button be the best option rather then constantly updating a home point I think it would be a better choice Return home or return to the controller location Look how many people use these drones off shore and they are constantly in motion and they have to fly their drones back to them for a handicap or land on a deck. If the drone considered the controller to be the home location wouldn’t that work out the best?

My rc 2 is back to being fast in the last software update but might just be me

I had to saw and cut the propellers off and use pliers to get the screws off lol

In France for all of May with my Air 3 and Mini 4 Pro…….very frustrating that the altitude on the Mini4 is limited to 120m when using it in rising terrain. I’ve tried to unlock the altitude limit by following your videos but all it does is directs me to a link to supply a ‘Class 0’ sticker. It’s a 2023 drone so I was under the impression I could unlock the altitude limit…….

@Donuts-rw2if

20 күн бұрын

Declassifying the drone was only possible till the end of 2023. Now your only option would be to get it certified as a C1 drone to be able to set the max altitude to higher than 120m above starting point.

My biggest problem with DJI is pre-existing software features not included in products. For example, on the DJI Mini 3 standard, I cannot turn off artificial sharpening, which makes the footage look worse. This is a common theme on DJI products. Sigh. I sent a request asking DJI to update software to allow me to turn off sharpening, but they don't do anything.

DJI should make a RC Pro2 that's compatible with all dji drones....o4 (Air 3/Mini4Pro) and 03+ (M3 series, Mini3 Series) with all the bells and whistles. I've always wanted the RC Pro because of its 32Gb on board storage, 1000 nit screen, and because it has buttons galore for an insane amount of customization. I'm kinda on the fence on either picking up one or the Mini4Pro Flymore Plus kit

@DMProductions

19 күн бұрын

I’d be happy with this controller with a better brighter screen and slightly faster. Having the lightweight size is a good advantage

Thanks for sharing... that's why I stick with dji mini 3 pro...👍

When’s the Mavic 4 due?

@DMProductions

19 күн бұрын

not sure,,,,,

The RTH bit has some confusing bit. How does it drain your battery life so badly when it thinks you're super far away?

@dereksmith9448

20 күн бұрын

He explains why in the video , the further the drone is away from you the more battery it thinks it needs to be able to get back to you

Good

From sarawak borneo malaysia watching🤝

My biggest complaint with the Mini 4 Pro is that the auto tracking consistently does not work. Why can't the drone stay within 20 or 30 feet from the controller? My testing with auto tracking this winter while skiing is that the drone stays close (desired) to a skier only for a few seconds; even when there are no trees, twigs, or obstacles between the drone and the skier/controller. The drone responds by flying higher and higher until it loses tracking contact with its controller. I believe that water or snow sensing maybe the culprit for my poor tracking issue? Mini 4 users tracking themselves also need a RC screen lock feature (similar to the Osmo Action), so they can fly hands-free. It is way too easy to touch or bump the controller screen settings and halt the hands-free ongoing tracking recording. And yes, an updating home point feature would be great for this type of drone use as well!

great video all the point are really on point for me I have issues with the drone as well make me dasapointed to be honest for a drone that still not quite cheap. I just got it and I was flying in sports mode I was coming back fast to home position and leave the stick to stop lolol... the drone never stoped I had to switch fast to cinema so the sensor turned on and ufffff its stop just right on the front of that Jesus big cross cimetary otherwise the drone would just have never stop I guess... and the stick was in the middle.... big fail and also with the sensor in normal mode its not going to stop its going to crash into those trees... and the hyper lapse I start on my face and do a pull back shot kind of fly away and when I start the process it comes back to me but like 2 feet aiming on the side of me in diff angle not even how I set it up so my shot is pointless... To me for now its ok but I bought this drone for some feature like way point and well it does not perform the way I thought it would If I knew this I would never have buy this drone... and stick with my mini 3 pro that was totally fine!

Hi Darren, I share a lot of your frustrations despite loving the Mini 4 pro, but I don't think it is fair to compare to the Air 3 :) That is a different category of drones altogether. Having said that, yes, the firmware is very slow to load, a bit sluggish and it has locked up and restarted at times while I was in the air!!!! I have lost a few shots because of this. The active track is great, but again, obstacle avoidance is not the best with it either. I have crashed and had the drone replaced under Care Refresh because of this. Battery life is what you can expect from the current technology, but yes, I wish I could get the extended one. Otherwise, I love the Mini 4 because of all the freedom you have as opposed to the Air 3. I actually struggled at the time to decide between them, but since I do a lot of photography in cities or around tourist attractions, the Mini 4 was the winner. I hope they fix the bugs in the firmware and make it load faster, it has been frustrating. Thanks for the video.

🤣🤣🤣🤣🤣😂 , little bart - WTF ??....... brilliant👌

@DMProductions

20 күн бұрын

Haha 😂

Amazing video keep it up Darren

@DMProductions

19 күн бұрын

thank you buddy

The “PH000” is suitable as a replacement screwdriver. Used by electricians

hi i had a hubsan zino pro it was horrid but it had tracking centered on the transmitter i now have a mini4 dji need to implomentit if poss happy flying

A video on what you don't like on the 4 is a good indication that the mini 5 is soon to be released

@DMProductions

19 күн бұрын

haha unfortunately not

I've actually flown the mini 4pro while I had my 3pro serviced at dji and I didn't like the behavior of it... The mini 3 pro to me is a better drone....

Haha love the Simpson graphics 😂

@DMProductions

20 күн бұрын

haha yes

For me..all I want is a variable aperture DJI Air 3..that would be my "perfect" drone..lol

@DMProductions

20 күн бұрын

Haha yes I have to agree although I’d take a 1inch sensor too on the wide ☺️

@ldmndz4652

19 күн бұрын

@@DMProductions yes..plus what you mentioned!..haha at this point for some of us who do not have an Air 3 yet..in the time frame..should some us just actually wait for the update Air 3S? Air 4?..which maybe coming in the next year?..or do you think tis too early an update for DJI's usually time frame when updating drone models?..every couple of years they do?..

Note this may be true of all Drones I don't know but, beware of bugs! live ones, they will empale on the sensors and interfere with many flight functions.

Can u still use this to make money

@DMProductions

18 күн бұрын

Absolutely yes !

That sharpness issue can be nullified if you use ND filters

@DMProductions

20 күн бұрын

Not necessarily, if you use pro settings and lower the shutter speed yes but if you shoot in auto and stick a nd filter on it’ll still look too sharp without changing that settings I mentioned

@DanieleRacca

18 күн бұрын

@@DMProductions I cannot find the sharpness settings you mentioned.. I think they removed it with the new software update