Thanks for watching. Don't forget to Like, Comment and Subscribe. #markdanielsjr #aluminumboat #tinrigboat #rangerboat Social Media: Instagram: markdanielsjr Facebook: Mark Daniels Jr.
Жүктеу.....
Пікірлер: 45
@TinboatTom4528 Жыл бұрын
I agree. In a tin boat you need to run sheathed wire. I ran 10gauge 3wire in mine. If a wire wears through you can make the hull live.
@MAB1907 Жыл бұрын
Sure enjoy your videos Mark, hope to meet ya some day, good luck 🍀 sir !!!
@keithkristoff9419 Жыл бұрын
Mark The wires that you guys ran can potentially burn an aluminum boat to the ground, if you don't install a fuse, or a circuit breaker at the Battery for every positive wire that you added. The fuse/circuit breaker is to protect the wires, not the graphs. The graphs will have their own fuse. If the insulation rubs off against a sharp piece of the aluminum hull, the wires will glow red and burn the boat down.
@MassReelFishing Жыл бұрын
Just bought a 106SV and LVS34 for my kayak! Picking it up today!
@Max-hz9vu4 ай бұрын
I have the same boat and was thinking about rigging mines myself but after watching this video I am looking for the nearest rigging shop 🤦🏿♂️ hellllllllllllppppp
@bill-qv3er Жыл бұрын
Try the Sea Clear wiring, you will be amazed !!!!!!!!!!!!!!!!!!!
@scychaser Жыл бұрын
What size is the garage... Yikes!!!
@troutnut01
Жыл бұрын
His garage is half the size of my house😂 “GOALS”
@martygreeson2032 Жыл бұрын
THATS A AWESOME SET UP...
@PHATBASSASSASSIN Жыл бұрын
That’s why you don’t use black and decker pecker wreckers 😂
@spencershenley6833 Жыл бұрын
I just got my 2022 188p finally working right. It's a great platform for the lakes in Michigan. I have four 12 inch helix. Mega live and target lock. I had electronics issues most of the summer. This is going to be a great boat for the next few years until I retire south.
@dfox7777 Жыл бұрын
Looks clean Mark! That's my fav part of a new boat!
@chantzbirch1151 Жыл бұрын
Will be doing this DIY soon once I figure out the best option for me and my old school rangey!
@keithawhitley Жыл бұрын
Might not want to put zip ties on the live scope transducer cable. Garmin recommends tape
@Chiefdixon Жыл бұрын
Nice nice setup Mark😊
@joereyes5700 Жыл бұрын
Your shop is legit!
@troutnut01 Жыл бұрын
Dude, your garage is TOO CLEAN. 😂
@DHW448 Жыл бұрын
It's a very nice setup, Mark. You will love it. I love mine & it is set up similar. These Ranger tin boats are awesome.
@larrytidwell4866 Жыл бұрын
I can't wait to see what you put in the boat this year....Good luck bruh
@whitebass16 Жыл бұрын
I had to rewire my last boat and it was a pain in the butt. I swore I wasnt gonna do it again also. Well I bought a ranger z522 and I upgraded my wire from the battery to the front deck for my solix and ultrex. Another pain in the butt, but I'm glad I did it
@mikehigh4321 Жыл бұрын
Happy for you bro now let’s go fishing put a few dollars on the line and let me give you your first loss on that guy lol
@justlooking2013 Жыл бұрын
Mark you seem to be in a new garage man congratulations, can’t wait to see you get it together
@JimGrady67 Жыл бұрын
Mark great tip about removing the side panel! As others said, I would suggest you use marine wire Its tinned and multi-stranded o give you better electrical flow. Check out the type of wire Seaclear or Westmarine use. I learned the hard way on my last boat with voltage drop and corrosion using hardware store wire. But if its all you could get you have to go with it for now to get on the water.
@TheCarhartt1 Жыл бұрын
This many years an man still got the Chevy he started with!
@troutnut01 Жыл бұрын
Marine wiring is different than the 8 gauge wiring you bought at the hardware store. Prepare to replace it soon. Boats are electricity friendly. Marine wiring is tinned with a solder in an oxygen free environment when manufactured to prevent corrosion. You may start to see weird interference on your graphs as the first sign. They also use a different coating. Hopefully your wire is copper, marine wire is pure copper and stranded, a lot of wiring made for the home is solid. Also, when pulling wires thru the boat, you can make it slide better just by either wiping the wire coating with wire pulling lube ( or water based KY 😂😈) . You need a breaker at the battery for that wire, it is so large it will burn a hole through your boat before you can get back and cut them. I would have individual fuses at the graphs and livescope box to protect them. $1 fuses vs $3k screens… a.co/d/gnQhAHS
@jt3ventures598 Жыл бұрын
Keep dropping vids man hopefully this year you are more active on the tournament vids. All #Bulletproof love 🖤
@jasonmausteller2488 Жыл бұрын
What charger for the starting battery? I only saw a 3 bank?
@P50302 Жыл бұрын
What rod racks are those in the background?
@MarkDanielsJr
Жыл бұрын
Custom build
@jdubya3498 Жыл бұрын
Coincidentally, mine is already hooked up to the truck, so just curious what time I should bring it by? Or come to Guntersville and trade all my waypoints 😎😇
@TheIceman101 Жыл бұрын
Brother I would have installed it for you. I installed my live scope and my friends.
@petecook1611 Жыл бұрын
Why didn't u just use sea clear harness mark? Curious
@notsogood6249 Жыл бұрын
You have to have the cleanest garage around. I noticed a NOCO 10x4 battery charger box...did you also do a battery swap to the NOCO?
@MarkDanielsJr
Жыл бұрын
Running Noco chargers this year
@batfreak6897 Жыл бұрын
Mark!!! No zip ties on the Garmin livescope ducer cable!!!! Use electrical tape.
@ronaldbryant8457 Жыл бұрын
I know these boats cost a fortune nowadays, and this would be an additional cost, but the boat manufacturers could pre-wired for all these graphs. Everyone orders their boats already knowing what type of electronics they will run. This is a lot of work that could be done in the boat build...
@katiedolfman6496 Жыл бұрын
Looks great! What foot pan is that? Love the cup holder. Will you post a link for the graph mounts and foot pan please?
@MarkDanielsJr
Жыл бұрын
Foot pan come with the boat and I’ll send you the link to graph mounts
@katiedolfman6496
Жыл бұрын
@@MarkDanielsJr thank you very much
@MarkDanielsJr
Жыл бұрын
@@katiedolfman6496 www.bassboattech.com
@mikegiles5162 Жыл бұрын
Garage so big you got an echo.
@jdubya3498 Жыл бұрын
Btw good luck upcoming ‘23 season! I see and forecast 2 BPT trophies 🏆 this year and a RedCrest top 3. Not sure if it’s a 1st 2nd or 3rd but it’s a top 3
@sleetherookie2929 Жыл бұрын
Mark be on top of his A game forsure lol. Great video bro. So I challenged TODD CASTLEDINE to a flipping and pitching heavy cover from the bank, best 5 fish, he agreed to that challenge but now I’m over here like what happened to a challenge that he agreed on and now it’s like he plead the fifth. Man I just wanted to see what you think about that because he said that he’s down for it. it’s all for fun as creators and anglers. I know you got that dust pan ready to SWEEP everyone up and hold that trophy bro…👊🏻
Пікірлер: 45
I agree. In a tin boat you need to run sheathed wire. I ran 10gauge 3wire in mine. If a wire wears through you can make the hull live.
Sure enjoy your videos Mark, hope to meet ya some day, good luck 🍀 sir !!!
Mark The wires that you guys ran can potentially burn an aluminum boat to the ground, if you don't install a fuse, or a circuit breaker at the Battery for every positive wire that you added. The fuse/circuit breaker is to protect the wires, not the graphs. The graphs will have their own fuse. If the insulation rubs off against a sharp piece of the aluminum hull, the wires will glow red and burn the boat down.
Just bought a 106SV and LVS34 for my kayak! Picking it up today!
I have the same boat and was thinking about rigging mines myself but after watching this video I am looking for the nearest rigging shop 🤦🏿♂️ hellllllllllllppppp
Try the Sea Clear wiring, you will be amazed !!!!!!!!!!!!!!!!!!!
What size is the garage... Yikes!!!
@troutnut01
Жыл бұрын
His garage is half the size of my house😂 “GOALS”
THATS A AWESOME SET UP...
That’s why you don’t use black and decker pecker wreckers 😂
I just got my 2022 188p finally working right. It's a great platform for the lakes in Michigan. I have four 12 inch helix. Mega live and target lock. I had electronics issues most of the summer. This is going to be a great boat for the next few years until I retire south.
Looks clean Mark! That's my fav part of a new boat!
Will be doing this DIY soon once I figure out the best option for me and my old school rangey!
Might not want to put zip ties on the live scope transducer cable. Garmin recommends tape
Nice nice setup Mark😊
Your shop is legit!
Dude, your garage is TOO CLEAN. 😂
It's a very nice setup, Mark. You will love it. I love mine & it is set up similar. These Ranger tin boats are awesome.
I can't wait to see what you put in the boat this year....Good luck bruh
I had to rewire my last boat and it was a pain in the butt. I swore I wasnt gonna do it again also. Well I bought a ranger z522 and I upgraded my wire from the battery to the front deck for my solix and ultrex. Another pain in the butt, but I'm glad I did it
Happy for you bro now let’s go fishing put a few dollars on the line and let me give you your first loss on that guy lol
Mark you seem to be in a new garage man congratulations, can’t wait to see you get it together
Mark great tip about removing the side panel! As others said, I would suggest you use marine wire Its tinned and multi-stranded o give you better electrical flow. Check out the type of wire Seaclear or Westmarine use. I learned the hard way on my last boat with voltage drop and corrosion using hardware store wire. But if its all you could get you have to go with it for now to get on the water.
This many years an man still got the Chevy he started with!
Marine wiring is different than the 8 gauge wiring you bought at the hardware store. Prepare to replace it soon. Boats are electricity friendly. Marine wiring is tinned with a solder in an oxygen free environment when manufactured to prevent corrosion. You may start to see weird interference on your graphs as the first sign. They also use a different coating. Hopefully your wire is copper, marine wire is pure copper and stranded, a lot of wiring made for the home is solid. Also, when pulling wires thru the boat, you can make it slide better just by either wiping the wire coating with wire pulling lube ( or water based KY 😂😈) . You need a breaker at the battery for that wire, it is so large it will burn a hole through your boat before you can get back and cut them. I would have individual fuses at the graphs and livescope box to protect them. $1 fuses vs $3k screens… a.co/d/gnQhAHS
Keep dropping vids man hopefully this year you are more active on the tournament vids. All #Bulletproof love 🖤
What charger for the starting battery? I only saw a 3 bank?
What rod racks are those in the background?
@MarkDanielsJr
Жыл бұрын
Custom build
Coincidentally, mine is already hooked up to the truck, so just curious what time I should bring it by? Or come to Guntersville and trade all my waypoints 😎😇
Brother I would have installed it for you. I installed my live scope and my friends.
Why didn't u just use sea clear harness mark? Curious
You have to have the cleanest garage around. I noticed a NOCO 10x4 battery charger box...did you also do a battery swap to the NOCO?
@MarkDanielsJr
Жыл бұрын
Running Noco chargers this year
Mark!!! No zip ties on the Garmin livescope ducer cable!!!! Use electrical tape.
I know these boats cost a fortune nowadays, and this would be an additional cost, but the boat manufacturers could pre-wired for all these graphs. Everyone orders their boats already knowing what type of electronics they will run. This is a lot of work that could be done in the boat build...
Looks great! What foot pan is that? Love the cup holder. Will you post a link for the graph mounts and foot pan please?
@MarkDanielsJr
Жыл бұрын
Foot pan come with the boat and I’ll send you the link to graph mounts
@katiedolfman6496
Жыл бұрын
@@MarkDanielsJr thank you very much
@MarkDanielsJr
Жыл бұрын
@@katiedolfman6496 www.bassboattech.com
Garage so big you got an echo.
Btw good luck upcoming ‘23 season! I see and forecast 2 BPT trophies 🏆 this year and a RedCrest top 3. Not sure if it’s a 1st 2nd or 3rd but it’s a top 3
Mark be on top of his A game forsure lol. Great video bro. So I challenged TODD CASTLEDINE to a flipping and pitching heavy cover from the bank, best 5 fish, he agreed to that challenge but now I’m over here like what happened to a challenge that he agreed on and now it’s like he plead the fifth. Man I just wanted to see what you think about that because he said that he’s down for it. it’s all for fun as creators and anglers. I know you got that dust pan ready to SWEEP everyone up and hold that trophy bro…👊🏻
First
Lmao “tin boat” hahaha