Dude you are my hero for posting this. Super good info!

@kapeldiy7482

2 жыл бұрын

Glad to hear that, hope my video helped you !

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger*

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger*

Most PD-USB power supply chips drop the power to 10W per port if multiple ports are used. If you need QC for every port you will need an independent chip per port on the trigger board

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger'

I think I will get this to convert my portable 60w solar panel 18v-15v DC to this

A great review. I bought some of this from Ali. Thanks a lot. :-) Five thumbs down from hate people, I think!

Hi, thank you for your video. Could you tell me if I can use this module for a DIY powerbank? Is it bidirectional?

@kapeldiy7482

2 жыл бұрын

Hi, its not bi-directional, so its not suitable for powerbank as a standalone solution, You will need separate cells charger

12.07 plus voltage loss equals 11.5 to the module. So at best the module was using 9V PD.

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger*

50c is very hot, especially considering it is free air right now. Think how hot it will get if it is concealed inside a vehicle behind the dash or enclosed in some housing without fans.

@kapeldiy7482

2 жыл бұрын

Indeed it's hot, I recommend using this module in vented environments, or using good heat dissipation. From the other hand my macbook charger is getting really hot when its charging the battery - I believe it can also reach 50c inside or even more

@lifeai1889

2 жыл бұрын

Actually it's fine It can handle 65w just don't use actual load use dummy load it can even deliver 100w with heatsink

I saw my Mac switch to 100w charging while using this module with a high power C to C cable. I'm not sure the module could handle 100w constant load but it probably has internal thermal throttling but might be bad to heat shrink wrap it and cover the chips without a heat sync first

@BeriNaafal

7 ай бұрын

Input voltage?

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger*

what can i do for a 12v motorcycle battery to get at least 2 amp???? is sooooooo slow whit my xiaomi reminote 9s, it dont charge just i can get a slow discharge :( helppp

When using usb a the module switches to 5 v it said in the institution’s

Is it hot when used with qc 3.0 or 18w?

Do you know what IC it using?

Nice module charger... 👍👍 Any 3D printing for this module? What CTP2?

@kapeldiy7482

2 жыл бұрын

Couldn't find any 3D printings for that module so far.. CTP2 its the only name given by manufacturer to this product :)

@ptbambich

2 жыл бұрын

@@kapeldiy7482 please let me know if any.... Thanks a lotssssss.... 😉

@emrekeremozyurt296

Жыл бұрын

@@ptbambich are u still interested? I designed non-professional case for it. I plan to upload it to printables or thingiverse. When I upload, I'll type here again.

@ptbambich

Жыл бұрын

@@emrekeremozyurt296 wow... Thanks a lot....pls do ASAP... 😉 How many channel you design? 2/4?

@emrekeremozyurt296

Жыл бұрын

Here is the link. As I said before it is not a professional design :) www.printables.com/model/281005-ctp2-charger-board-case

If i solder a battery to this circuit, can i chanrge and discharge with this module or is it only one way?

@4Mi360

Жыл бұрын

No

19V output charging smartphone with need 5V. This PCB can regulate volts whiting explode dispositives?

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger*

Pm me can you to install do solar panel of charger'

Can this be used as a replacement for a cellphone charger? assuming daily use

@aleksinvest7

Жыл бұрын

Yes, you can use this modul everyday, for charging your phone

Hi how much input Voltage and Amperes Needed to function it’s PD charging.

@kapeldiy7482

2 жыл бұрын

Hi ! It depends - PD can be activated at 9V 12V 15V and 20V on output, but the rule is, that input voltage should be at least 3V higher then expected on output. So If you have a device which runs on 20V PD - you should consider 23V or higher on input

is the module working on,,,input DC 20V/4.5A -> output PD Type C laptop ??

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger*

I have power bank 5v with usb step up 12v. if I use step down 5v 4a can it work?

@Thekiloslaundry

Жыл бұрын

sorry the goal is to increase the amperage at the output of the power bank because the power bank only runs on 5v 1a capabilities

last week i buyed this module but work only 10 watt when i use more than it is shut down and very hot

@kapeldiy7482

Жыл бұрын

So probably you have a defective module, I got a bunch of them, and all charging without issues

@ibrahimyildirim252

Жыл бұрын

@@kapeldiy7482 i fixed, little component was broken now no have problem thanks

@AnasAnsari_7

Жыл бұрын

@@ibrahimyildirim252 hey my board is behaving like yours can you tell me what you fixed

@ibrahimyildirim252

Жыл бұрын

@@AnasAnsari_7 next the +positive terminal have little component you need skip this komponenet or make short. If still not work when shut down check the component temperature same one need be so hot .good luck

Does it have a galvanic isolation from the PSU?

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger*

Could you test it with xiaomi supported QC4 or QC4+?

@kapeldiy7482

2 жыл бұрын

I will try, need to find some phone with it

im powering this with 12v but i keeps on and off..do i have defective board?

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger*

What does the less indicate? If i may ask?

@anwin85alon

Ай бұрын

Pm me can you to install do solar panel of charger*

Hi, what you used as the power input source?

@kapeldiy7482

2 жыл бұрын

For testing purposes I used Lab power supply, but you can use any DC power supply. Check my other video kzread.info/dash/bejne/qKWCsLOCocy4qtI.html&ab_channel=KapelDIY in which I'm building the charger based on old laptop power supply, if you wish to use PD with 20V you have to use 25 volts or above on the input

does this module support fast charging vooc 3.0 oppo/realme?

@kapeldiy7482

Жыл бұрын

nope it doesn't, realme, oppo are charged with max 15W using this module

@wahyusetiawan5832

Жыл бұрын

@@kapeldiy7482 oke thanks you.

Can it charge which support quick charge 3 device

@kapeldiy7482

2 жыл бұрын

Yes it can, it supports QC from 1.0 to 4+

@steavekamei2013

2 жыл бұрын

@@kapeldiy7482 okay

Is this good for powerbank

@kapeldiy7482

9 ай бұрын

I don't think so, module itself is consuming some power even not charging anything, and it will drain the cells

@BeriNaafal

7 ай бұрын

​@@kapeldiy7482 How about adding an on/off button? Like.. only switch-on when using the powerbank. Will there be another problem?

Can it charge fast on "one plus " phones?

@kapeldiy7482

Жыл бұрын

Yes I think so, as long as the phone is comliant with PD standards - probably PD 3.0 or 4.0

@rabbippfx

Жыл бұрын

@@kapeldiy7482 " one plus " has a unique charging protocall, 'dash, wrap etc ' . These phones cannot charge fast with any fast charger, they just need the "one plus charger" . That's why I'm asking. It needs to be checked physically with this module. Only then you can get the right answer. If it's possible, please make a physical test ..... Then reach a certain decession. Thanks

@kapeldiy7482

Жыл бұрын

@@rabbippfx You are absolutely right ! seems like One plus is out of PD standard ! What you can expect is 15W of charging power according to manufacturer, checked by other people.

Can it boost from 12v to 20vPD?

@kapeldiy7482

2 жыл бұрын

Nope - the input voltage have to higher then expected PD voltage at the output

@infiniteoffset

2 жыл бұрын

It can do 20V 5A, but it needs like 24V input. Also it gets really really hot, so some additional cooling might not be bad idea to consider.

@yoyatech4800

Жыл бұрын

@@kapeldiy7482 thanks, nice info, so it's like only able to step down the voltage right?

@kapeldiy7482

Жыл бұрын

Yes, exactly