DIY induction heater by welding machine
make your diy induction heater
this video help you to build simple induction heater by welding machine , coil and capacitors .
the variable resistor replace to resistor in pin 9 of uc3846 ( pwm ic ) to change the frequency.
Пікірлер: 165
Terima kasih atas ilmu pengetahuan Yang di berikan nya 👍🙏🙏
Нифига! Вот это вот классный способ охлаждения конденсаторов
thats really neat wish i understood how you did that thanks for sharing
a good project, you are very good, the welding machine has many uses
This project is very good!
very nice video my friend.. thanks for sharing this video 💗 big like 👍 👍 👍
That's so cool I have a 600V 3 phase old Miller Welder will use it for this
@funwithelectronic4140
Жыл бұрын
What kind is that , inverter or transformer ?
@matiasdiazduran5806
Жыл бұрын
@@funwithelectronic4140 It's old so it could be transformer might not work for it :\
@funwithelectronic4140
Жыл бұрын
Transformer not work . But you can find old inverter and make this .
Incredible! Do you connect the black wires of the toroid to the output of the chopper transformer that powers the welder?
Great project! It'd be even nicer, with a little more detail, like a block diagram.
Awesome! At what point do I dunk the entire set-up into the water as I'm having a bath?
Creative video, thanks for sharing :)
Ainda não tinha visto desse jeito
Good video🙂🤝🤝🤝
Can You put a block diagram of all connections?
@funwithelectronic4140
Жыл бұрын
Yes . I do as soon as possible.
@1lt3r
Жыл бұрын
I'm waiting too
@carloshenriquekampine1821
Жыл бұрын
Assim que tiver ficaria agradecido também.
@mksimo70
9 ай бұрын
It's been almost a year where is the diagram block
@Key_Capz_
6 ай бұрын
the welder is just a power supply. You still need the rest of the switch and caps to create the right frequency. or just buy it made ond use the welders as a power supply.
That Good and Number one ❤❤❤
Hi! Please, I don't understand, that new toroid pirmer wire connected you, to original transformator primer wire with paralell? FET can it use 2 paralell primer transformer? Thank your answer!
Good job
Does the section where you heat the metal plate suggest that the field is strongest at the edges in the work coil??? Thanks for the great video!
@funwithelectronic4140
Жыл бұрын
No. The strongest field is in the middle.
@dalenassar9152
Жыл бұрын
@@funwithelectronic4140 ARE YOU POSITIVE????? There is mathematical proof, also numerical and computer simulation (based on the BIOT-SAVART LAW) that strongly suggest it is nearer the inner edge, more specifically, being at a locus of points forming the "circle of MAXIMA" around the exact inner center of the coil. In fact, the weakest flux density is at the very end of the 'centers' of the coil (two points), where the flux here is exactly half that at the middle center axis.
@dalenassar9152
Жыл бұрын
I see that where you place a piece of sheet metal over the coil, it heated far more along the outer coil area. I think this isn't just from a hot coil, but from the much stronger magnetic field at the edges of the inside of the coil. To test this very simply, insert a fireproof sheet between the coil and sheet (or just hold it slightly above the coil). You should see that the max. induction heating is due to the field being much more intense at the INSIDE perimeter of the coil.
The max temperature it can rich is ?
Nice work... I need some help for building the sam machine.. kindly reply
Nice video, and thanks for sharing. Can I use another means in place of welding machine. And what is the energy consumption. Thank you
@funwithelectronic4140
Жыл бұрын
You can use any chopper. 4 kw
@yusifsuleiman5502
Жыл бұрын
@@funwithelectronic4140 thanks for the reply
Good work .. Can this idea help me to melt platinum ? Could the temperature reach to 2500 Celsius? Thanks
@funwithelectronic4140
Жыл бұрын
Yes . It can
Can be melting 2Kg Cooper? block diagram pls thanks Bro.👍
What temperature can it reach?
Perfect video. How much output power?
@funwithelectronic4140
Жыл бұрын
4kw
can it melted the steel?
Ha a vörösréz csövet felmelegíted ,hideg vízzel gyorsan lehűtöd (mint ha edzenéd ) azonnal meglágyul , Könnyen hajlítható .Kívánt hajlítás után felmelegíted újból ,de nem hűtöd le ,újból vissza keményedik .
very interesting! how many consecutive hours can it heat? I want to use it for a hydrothermal reactor (~12H of non-stop heating). do you think it's possible? THANKS
@mksimo70
9 ай бұрын
لا أظن ، لأن ماكينة اللحام معمولة فقط للعمل لبضع ثواني
Perfect
Bro, you are Nabeghe!😉, you will have an awesome channel! So is that tap water you used for cooling?
@funwithelectronic4140
Жыл бұрын
Yes . By 12v simple water pump
@rahasia_allah
Жыл бұрын
how many smd resistor code did you throw away?
Me pregunto que pasaria si conectaras un nucleo de flyback de tv en lugar de esa bobina 😮 sacaria un Arco como de 30cm😮😵
@Slawek_EU07
Жыл бұрын
Connecting the TV flyback transformer is possible, but it will probably burn out when trying to obtain an arc due to the high power of inverter welder. El posible conectar ed TV flyback transformador pero probablemente se quemará al intentar obtener un arco debido a la alta potencia de la soldadora.
Yeah yeah, you skipped the most important part at time stamp 3:39 where you pass the thick tube through the ferrite core, and all of a sudden there are two turns wrapped around the core a second later with the video skipping the critical part! Thanks a lot!
@paradiselost9946
Жыл бұрын
wha? whats so critical about seeing some pipe get bent? if you cant figure out how to wind a bit of pipe through a toroid (and anyway, its better to used a gapped ferrite core, not a toroid) then maybe you shouldnt be contemplating projects that require dealing with copper pipe...
Mais gostei muito
parabéns precisa ver se isto procede cadê o esquema das ligações corretas
@yuriperes83
10 ай бұрын
Misteeeeerio, kkkkk
ما شاءالله 😮
hi 👋... great ! can you upload the full video please ?
@funwithelectronic4140
Жыл бұрын
Hi . Which part do you want information about
hey, please tell me, what is that black kind of wax... that melts by heat and glues the wires together? what is it called? it seems extremely useful! Thanks!
@funwithelectronic4140
Жыл бұрын
Hi . It is black hot glue. Usually Used by hot glue gun.
mantaaaaaaaaaaap kreatif
@rahasia_allah
Жыл бұрын
Abang paham cara buatnya ya..tolong bntu sya bang 🙏
Congrats
2:38 how much H or uH is that inductor? Should two parts of inductor be separated ( I mean starting and ending point of winding)?
@funwithelectronic4140
Жыл бұрын
Hi . I don't measure the inductor . Inductor is 7 turns. two turns wire belongs to transformer. Transformer is 20:2 .
The resonant circuit is series resonant. Affected by load. The inductance and characteristics of the important toroidal transformer are unknown.
Inverter welding machin sa spot welding karsaktahu kaea sir
"DIY SIMPLE INDUCTION HEATER WITH WELDING MACHINE - RECALIBRATION" on KZread has parallel resonance. Which has better results: series resonance or parallel resonance?
هل يمكن لاحد ان يفسر لي كيف ان هذا السلك الاسود الضعيف الذي قام بلفه على الملف الحلقي يتحمل كل هذا التيار وكيف ان ملف الفيراييت لا يسخن
Gostei 👍 👍 👍 👍 👍
Good work, What is the Freq output of the coil and Is it a sine wave? thanks
@funwithelectronic4140
2 жыл бұрын
Hi . The freq is 60khz , yes sin wave
Sir Is the potentiometer that you installed to adjust the frequency or duty cycle? what pin did you connect it to?
@sateeshum394
11 ай бұрын
description clearly states its for frequency change...
hi you connect wire to chopper ...you mean transformer chopper or drive chopper its very unclear for me
@funwithelectronic4140
Жыл бұрын
Hi. Driver chopper doesn't have enough power . Wires connect to transformer output. Thanks for comment.
Pls make a video using induction stove modified in to induction furnace that can melt some gold
@funwithelectronic4140
Жыл бұрын
Hi . Thanks for watching and comment. I will if I find an old induction stove.
@marianodiaz461
7 ай бұрын
I have a old induction stove, the problem is that I have read that the coils are at potential....
ola amigo tenta derreter 800 gramas de FERRO puro ouaÇO por este precesso !!!
"wires connect to chopper output" Chopper or copper ? This confuses me..😂 Where are the two ends of the copper pipe coil connected? Which you put the capacitor on.
Very good DADASHAM DAMET GARM
😘👌
Sir this could be use for copper pipe?
@brutusmaximus5380
9 ай бұрын
Use a material that attracts magnets such as iron. Copper is non magnetic and takes a longer time and needs more power and higher frequency mainly because of the thermal conductivity of copper is so great.
like🙏👏👏
Hello sir. Could you please explain what is the small resistance that was replaced by the variable resistor. It was not clear in the video.
@funwithelectronic4140
Жыл бұрын
That resistance set the frequency of switching. the frequency must set to resonance frequency of tank RC.
Objects Buying link please share
❤❤
Frecuency and current without load?
@funwithelectronic4140
Жыл бұрын
Hi .no load Frequency 60khz and current 35A .
Work for copper orang not bro
Hello how long this diy induction heater can run continuously ?
@funwithelectronic4140
Жыл бұрын
There is no problem if capacitors and coil cooled.
Hi dear, this machine can be melting 100 g gold? and how much power (kw) is the device?
@funwithelectronic4140
Жыл бұрын
Yes . It can
@rahasia_allah
Жыл бұрын
how many smd resistor code did you throw away?
What is the maximum temperature it can produce?
@funwithelectronic4140
Жыл бұрын
2500 c
What is the function of the variable resistance.thanks
@funwithelectronic4140
Жыл бұрын
Hi . For freq adjust. See comments please.
@flstudio-bitcoin935
Жыл бұрын
@@funwithelectronic4140 pls schéma
please make a new video, friends, using the new inverter, I'm waiting for your notification to sound🙏🙏
Hamen yah project chahie
I wanna build one of these to refine metals. Your design seems like the best one on here, but I’m electrically ignorant! We need better instructions please!
@funwithelectronic4140
Жыл бұрын
I'll upload another video with full details in a month.
@user-sg1fs6vy4e
8 ай бұрын
@@funwithelectronic4140уже год прошëл,а где же видео?
how many smd resistor code did you throw away?
@funwithelectronic4140
Жыл бұрын
one resistor . freq adjust.
@rahasia_allah
Жыл бұрын
@@funwithelectronic4140 what is the voltage code for the resistor you unplugged?
@funwithelectronic4140
Жыл бұрын
Hi . The pwm ic is uc3846 in this machine. Pin 9 of ic is Rt for frequency adjustments. You must throw away this resistor and put the variable resistor .
@rahasia_allah
Жыл бұрын
@@funwithelectronic4140 that you connect to that output from negative positive ct or rd ?
Next to it you tray to snif to close🙏 Trai a litle more further please 🙏😍🙏😋🙏 🙏💜🙏
Where u add variable resistor
@funwithelectronic4140
2 жыл бұрын
Hi . Pin 9 of ic(uc3846) . For freq change to resonans
@fabriziobrutti1205
Жыл бұрын
@Mahmoud Raddad duty cicle it's fixed to 50%, about the frequency, give a look at the datasheets and use some math
how much frequency you needed
@funwithelectronic4140
Жыл бұрын
60khz
@ednietoz
Жыл бұрын
i will made it soon.....thx brother...great idea
Αγνοστο σε ποιο σημείο θά συνδεθεί στην ηλεκτροσυκολληση άγνωστη προέλευσης φερρίτης
En lugar de poner música mejor explica bien como se hace Que se necesita y diagrama Así no se puede 🤨
@funwithelectronic4140
Жыл бұрын
I dont know your language. Please ENG
How many turns, gauge etc should be mentioned in the video itself. Music is too loud and irritating.
@funwithelectronic4140
2 жыл бұрын
Hi . 20 turned in primary
@rahasia_allah
Жыл бұрын
how many smd resistor code did you throw away?
I want to buy it
@jonnybro..9999
Жыл бұрын
I want to heat it upto 700degree and want to add automatically timer switch to stop it
@jonnybro..9999
Жыл бұрын
Please reply
@funwithelectronic4140
Жыл бұрын
hi Please come funwithelectronics22@gmail.com
Can this melt copper?
@funwithelectronic4140
Жыл бұрын
Yes . Up to 300 gr copper .
@rahasia_allah
Жыл бұрын
how many smd resistor code did you throw away?
i see black and white cable conected to capasitor and work coil, what cable it is? and where is conected from?
@funwithelectronic4140
Жыл бұрын
Hi . Black and red cable connected to oscilloscope . For reaching max amplitude (by variable resistance tuning)
@funwithelectronic4140
Жыл бұрын
The black cable from chopper (300 vp-p)
@funwithelectronic4140
Жыл бұрын
And the white cable is secondary of transformer. Transformer is 20 : 2
@ednietoz
Жыл бұрын
choper out ussualy have 4 pin out, 2 red pin out and 2 black pin out, every two cable red or black is conected together? or you just put in one black and one red pinout? because if you jumper 2 black chooper output it will make double 475K red ceramic capasitor from mosfet or igbt
@ednietoz
Жыл бұрын
very clear explanation, i thinking before red and black clips is feedack current sensing...in fact it's connected to oscyloscope 😁
I just come here to have a rave
Sir .sho project diagram
Hello
do you have WhatsApp .. i really want to make it , please give details of the schematic .. thank you very much 🙏
@funwithelectronic4140
Жыл бұрын
Hi . Please comment your phone number here , for sending schematic.
@rahasia_allah
Жыл бұрын
I'm very happy .. thank you very much I make sure your audience will overflow soon.. thanks very much .. I'm very happy to communicate with you..whatsapp me +6285721885965
@rahasia_allah
Жыл бұрын
@@funwithelectronic4140 hope you contact me.. thank you 🙏
@rahasia_allah
Жыл бұрын
@@funwithelectronic4140 when does your friend give a schematic on my whatshap? 🙏
If you don't show any connections, how can we know what you are doing... 👎👎👎
@funwithelectronic4140
Жыл бұрын
Thanks for comment. I'll upload another video about induction heater with more details .
@chongshenchang9367
Жыл бұрын
@@funwithelectronic4140 Ok, Thank you
Feak
Insufficient explanation
Subtitles? And the music is awful. Just speak on your native language. Interesting but unwatchable
Fake 😃🖐️😃🖐️😃🖐️😃
Tebrikler
Hi, i am the owner of this welding macgine brand and factory owner, thanks for this video, please contact me if you need new samples for new videos
@funwithelectronic4140
Жыл бұрын
Hi . Please send your email. Thank you.
@hassanyaghouti601
Жыл бұрын
@@funwithelectronic4140 how many times I send reply to you , youtube delete
@hassanyaghouti601
Жыл бұрын
@@funwithelectronic4140 find our contact detail at our website spad.co.ir/contact-us/
@funwithelectronic4140
Жыл бұрын
Thanks
@ALLTNOR
Ай бұрын
@@hassanyaghouti601отличная техника , но в Украине ее не купить.
Apna contact number dijiye aap kahan se Hain
Good 🙏🙏 subscribe aur help Karen