I have no reason to watch this video, but yet I’m intrigued.

@EverydayHomeRepairs

9 күн бұрын

It is a interesting process 🙂

Having used an epoxy coating in two different garages I can't emphasize how important it is to properly prep your floor. The degreasing/acid wash method is not adequate. Grinding down the concrete is an absolute must. Failure to do so will ensure poor adhesion of any product. Scott does a wonderful job of explaining the process. Don't shortcut any steps. Good materials cannot overcome poor prep.

@EverydayHomeRepairs

8 күн бұрын

Amen, thanks for the feedback!

Just had a quote for this job from a professional company. $4200. This is well worth the effort for the savings and results! Well done!

@EverydayHomeRepairs

8 күн бұрын

Was the $4,200 for a 1 day project? There are some new-ish companies and processes that get in and out in 1 day.

@Busydadgarage717

8 күн бұрын

@@EverydayHomeRepairs yes. 1 day and done. That was their deal.

I'm loving the beetle or whatever it is, it's been with us through the whole process so far :)

@EverydayHomeRepairs

9 күн бұрын

😂, just hanging out the whole time

Great video Scott. After watching your video I'm going to hire it done. I'm old and not up for that much of a DIY challenge. Thanks for sharing.

@EverydayHomeRepairs

8 күн бұрын

You bet, at least now you have an idea of the different steps even if you get it hired out. Knowledge is power 👍

Another thing is you can use the angle grinder and grind the side concretewalls right below the drywall, and then use a paint roller and put on more epoxy + flakes, gives you a really nice clean look on the edges too! Plus its more waterproof kinda like caulking your corners in the shower!

@EverydayHomeRepairs

9 күн бұрын

I agree and would have done that exact thing if I didn't have the expansion joint all the way around.

@Vincent-rq4dx

9 күн бұрын

@@EverydayHomeRepairs oh wow that was a joint? Just looked like the edge my bad! Interesting spot they put it!

It ideally wouldn’t need to be said, but if you’re using a gas powered grinder, make sure you leave the garage door open and set up ventilation to blow the byproducts of combustion out. If you have living space above the garage, ventilate that too.

Great video Scott. Very informative.. What an awesome result.

Wow. It is definitely shows the best out of the three. You get what you pay for. Well done.

Thanks Scott, another perfect video as usual!

@EverydayHomeRepairs

7 күн бұрын

Thanks so much for the feedback and support 👍

Nice video. I did this when we bought our home seven years ago with a 3-car garage during a week when it poured rain the whole time in Seattle. The Oneida Dust Deputy was a good addition for the shop vac to help with concrete dust (yes, there's lots of it). Used a different product with only a single step epoxy but quite similar otherwise. It's held up great except for cracking using a floor jack to lift cars (added a plastic sheet to distribute weight under jack which solved that problem). I was surprised at how far what seemed like a small amount of epoxy spread on the floor. I do it myself again.

@EverydayHomeRepairs

8 күн бұрын

Thanks for the feedback. It is a nice project where if you follow the steps and take your time the results are awesome. Also, not bad saving $2,000 - $3,000 as compared to getting it hired out.

Very nicely done. Love your videos - they have helped me with so many household projects. But my conclusion at the end of this one is that I don't care about my garage floor all that much 🙂 I refinished a bathroom floor (over nasty saltillo tile with huge grout lines) using the rustoleum product. It's fine except that it's so dangerously slippery. Going to tear it all up and go with LVP next year anyways.

500 ft garage is 80% the size of an apartment here. Geez that much storage space would be nice

Great video and excellent results, thanks for this demo!!

@EverydayHomeRepairs

7 күн бұрын

You bet!

Yes, def worth the upgrade. Great job.

my Rustoleum lasted 10yrs, ended up thinning out, hot tires damaged it too diamond grinding off the old coating, and layering on the new epoxy+clear 5+ yrs ago; bombproof - and like others have commented; it the prep / grinding. also note; there's 2 different Rustoleum products being sold Rock Solid is the better option.

I *always* knew there were superior, industrial grade epoxy floor products available out there because I've seen really durable epoxy floors in commercial buildings that are definitely more durable and resilient than the Rustoleum product. If I ever do my basement I will be sure to use this far superior product. Here's a question: Are the flakes just for aesthetics, or do they actually add structure to the epoxy coating?

I think this is amazing. I had the DIY coating on a concrete floor and it did fail at the 6 month mark chipping etc.

@EverydayHomeRepairs

9 күн бұрын

Thanks for the feedback!

Looks amazing. Great video. I think its worth the extra money.

@EverydayHomeRepairs

8 күн бұрын

Agreed and thanks for the feedback!

Informative video, thanks.

@EverydayHomeRepairs

8 күн бұрын

You bet!

Yes. I watched a few videos from another channel. It was a professional doing the garage floor treatment. He said grinding is the only way to have a good long lasting epoxy coating. Your floor coating looks really good.

@EverydayHomeRepairs

8 күн бұрын

💯

Hmm I think I'll leave the concrete uncoated after all. The grungy look gives it character lol

Nice work. It looks like those spiked shoes really make it a lot easier not to mess up the sequence and flow of things.

@EverydayHomeRepairs

7 күн бұрын

Absolutely and those are a must have for this type of installation

Great Video mate. I have watched both the DIY version and this one, and just want to make sure - you mention not to wet the floor for the professional product. Is grinding the floor enough to get rid off the oil drip spot on the floor?

@EverydayHomeRepairs

9 күн бұрын

If you have oil I would get the specific primer they make for the oil problem spots to give you the best shot of it lasting. concretefloorsolutions.com/store/epoxy/cfs-oil-stop-primer/ and don't forget the promo code "ehr10" at checkout for a 10% discount 👍

This is a great video. Please let us know how it lasts. Great job in both the installation of the floor and the making of this video!

@EverydayHomeRepairs

7 күн бұрын

Thanks so much!

Great video! How does the time, energy and risk (no warranty) compare to a professional service?

Thank you. This convinced me to not use the Rustoleum product.

Any thoughts on cutting additional expansion joints before applying the product? 🤔

So is the epoxy inert when dry or does it continue to off-gas chemicals?

Awesome job!! Great info! Did you scrape or pickup any of the loose flakes before the clear coat? Is there any difference in the grinding profile between the hand grinder and the rental?

@EverydayHomeRepairs

9 күн бұрын

I left all the loose flakes in place. If I would have spread a bit more flakes I would have done a scrape and collection of the loose flakes prior to clear.

@EverydayHomeRepairs

9 күн бұрын

The grinding scratch/profile was pretty similar between the diamond cup wheel I had on the 4.5" and 7" grinders and the diamond pads on the rental.

@timhill5426

9 күн бұрын

@@EverydayHomeRepairs Awesome! All this info gives me the confidence to diy. Thanks!

HI Scott, Excellent video. How did you clean up the rollers between products? Or did you throw them away & use fresh roller for each product? Thanks again, dean

@EverydayHomeRepairs

6 күн бұрын

Fresh roller for each of the 3 layers 👍

@deanfiorentino6708

6 күн бұрын

How did you prep the corners?

Was there a sweep/vacuum after the flakes cured in? Wouldn't there be some amount of excess to remove before clear coating over it?

@EverydayHomeRepairs

8 күн бұрын

If you are doing a "Full Flake" there is often a scrape and collection of extra flakes. In my case I did a heavy flake and didn't do any collection of extra flakes and everything turned out great. You want to avoid clumps of flakes that would not be covered by the clear coat as that will change the final sheen and look of the surface.

Wouldn't it have been better to wait until the fall for temps that wouldn't risk a bad seal of the coatings?

Scott, what products did you use? We're doing this soon and do not want to go the kit way.

Do you have to grind all the time before applying the priner and epoxy? I watched a few videos on epoxy coating but i havent seen them do it

@nothingtoseehere93

9 күн бұрын

Chemical coating doesn’t last and it’s crap you always need to grind

How does the total cost of this project with pro-grade materials compare to the cost to hire the whole project out to the pros? I saw a video recently of a project hired out to pros in Alabama for a 3-car garage, polyaspartic, full flake, clear coat, that only cost $3600. I was shocked how low the price was!

Any reason why you did not beyonds the garage door?

Wow

Used the same rollers on all finishes?

@EverydayHomeRepairs

8 күн бұрын

Yep 👍 same type of roller from the kit but new roller for each of the 3 coatings.

Apologies if I missed it in the video. Total cost and square footage for this garage?

@EverydayHomeRepairs

9 күн бұрын

With grinding tools/rental and materials $5 per sq ft.

@jpalarchio

9 күн бұрын

@@EverydayHomeRepairs I'll have to confirm but sounds like about 50% to 75% of paying to have it done. Good to know!

Looks great!! That's A LOT of work for the avg DIYer. Not sure I would tackle that one. Given the cost of almost $2000 for materials, what would be and avg. cost of having a professional do it?

@ignacio..9

2 сағат бұрын

$7-$10 per sq ft.

how long was the curing time between the primer and intermediate coat?

@EverydayHomeRepairs

5 күн бұрын

I waited about 7-8 hours. Between 8-24 hours is ideal assuming temps around 80F

Being realistic, for a DYI how difficult would you call this medium, hard, pro, legendary?

@EverydayHomeRepairs

9 күн бұрын

I would say Medium to Medium-Hard.

@beanpotatoreviews184

9 күн бұрын

How many devices would you recommend renting rather than buying? You're putting a lot of confidence into someone who is newer into DYI ​@@EverydayHomeRepairs

If you don’t: * Diamond grind the floor?, * Test the hydration level seeping through? * Seal-Coat prime PRIOR to installing the epoxy, then flake, then Aspartic clear. Might as well not even bothering doing it.

Link to shoe covers?

@EverydayHomeRepairs

9 күн бұрын

concretefloorsolutions.com/product-category/accessories/ and don't forget the promo code "ehr10" at checkout for a 10% discount 👍

Coatings will only last a long time, if it’s a fresh concrete pad. The curing of the cement will absorb the coating to hold. And it will cure for months

So what would happen if you did the full grind, but the non commercial kit?

@EverydayHomeRepairs

9 күн бұрын

I think the results would be somewhere in the middle. The DIY kits usually don't come standard with a primer so if you get their primer as well and also used the clear coat you would have a much, much better shot of it lasting as compared to degreasing, etching, and apply the Epoxy/Flake which is the standard kit/process.

Did you look into any other companies for supplying the product? Curious if there was a specific reason you used concrete floor solutuons over someone else.

@EverydayHomeRepairs

5 күн бұрын

I had seen their videos and reached out as I liked the idea they were professional installers actually doing floors and also offering the same products they use for purchase. I worked with them on repairing a crack last year with their rapid set epoxy with great results. That is why I was confident in selecting their Epoxy floor Kit. 👍

@Flightless_Mike

5 күн бұрын

Thanks for the response! And nice work!

At the end of the video he stressed that the prep was the biggest difference between the products. Does that mean that the rustoleum is a good product if same prep was done?

@Casmige

9 күн бұрын

You really want 100% “solids”. The big-box store products are usually 50% or less (allows for longer drying and set-up time). If you go with the more solids mixture? Don’t leave it in the bucket you need to mix it in the bucket & then almost immediately start ribboning it out on the floor because it is vulcanizing in nature to set-up & the more concentrated it is (as in a bucket) the quicker it will set-up because it’s captured in such a small area…..Whereas ribboning it out onto the floor buys some more set-up time.

@GannDolph

9 күн бұрын

@@CasmigeThe main reason this happens is that the curing process is an exothermic chemical reaction (polymerization) that produces heat , and heat speeds up that same reaction. Thus you need to spread it out horizontally to avoid trapping and concentrating all that heat, which can basically cause a chain reaction of premature rapid curing. Same goes for bondo, quickset drywall mud, plaster of paris, RapidSet cements and mortars and so on..

A lot of work but worth it. Longevity is better than cheap way.

@EverydayHomeRepairs

8 күн бұрын

I agree for these type of projects where you are putting in some time it is nice to use the professional-grade products and have it last for a long time avoiding the same project coming up in 3-5 years.

You should have kept going onto the concrete driveway 😜

The Flakes make it hard to see dropped nuts and bolts.

@EverydayHomeRepairs

8 күн бұрын

Yes they do 💯

@n9wox

8 күн бұрын

Depends on the flake colors

Epoxy floor in basement, yay or nay? Why?

@mattp4079

9 күн бұрын

the off-gassing of these products is a concern for enclosed spaces.

@nothingtoseehere93

9 күн бұрын

Humidity would be a concern you would need to add a moisture barrier but if you have plenty of ventilation it could be fine. Would be a pain to clean

Pro grade ftw

@EverydayHomeRepairs

2 сағат бұрын

👊

22:46 The problem is, Scott, you grinded away the more budget friendly products before we could even see how well it held up. I respect that some people had it not last that long, but others did have it last. You usually are very good at doing things thoroughly and I would have liked to have seen how it fared for you over time. It would have been more beneficial to me at least.

@EverydayHomeRepairs

8 күн бұрын

Thanks for the feedback, unfortunately this house will be sold soon so I wouldn't be able to give the update in a couple years. Thanks for the feedback and I will keep that time of testing in mind for future garage floors 👍

10:22 I hope that bug didn't get in the epoxy!

@EverydayHomeRepairs

8 күн бұрын

We had 3 or 4 that made there way in but overall that was less than I was expecting.

This definitely does not seem DIY. And as others said on the last video- the tools and chemicals are so expensive you’re barely saving money over using a pro- who will almost certainly do a much better job. I still vote for buying rubber mats if you want to make the garage floor prettier. 🙂

@johnny8927

9 күн бұрын

Rubber mats seem like a good idea lol

$1800 isn't bad. To hire someone would cost $10000

Leave the cement ALONE!