You know, this squeak sound was desirable in japanese castle floors. The sound was an alert for enemies or strangers coming inside when walking throuh the corridors. Taking this squeak off makes your home losing security in case a samurai decides to break throuh.

@LongologoProductions

3 жыл бұрын

@Argean Comics: Yes! The nightingale floors in Nijō Castle (Kyoto, Japan)!

@vipka9

2 жыл бұрын

This will come in handy when I decide to go to Japan instead of meeting Monica in Paris were we promise to meet instead i bring my chandelier to my secret castle n the only way to get into the secret safe is to use the creamy floor board as audible tones to unlock the safe to stash the chandelier that I stole from Tiffanys causes it's priceless true fans will know my story of course I couldn't give the original perfect crime because then someone will know n it won't be perfect

@argeancomics3291

2 жыл бұрын

@@vipka9 😄😄

@LongologoProductions

2 жыл бұрын

@@vipka9 : 🤣

@Mars-zgblbl

2 жыл бұрын

Experienced invading ninjas would take off their belt, roll it up and then throw it to unroll it across the squeaky floor, spreading their weight

I used these screws about 8 years ago and they're still holding fine. I, also, bought some of the Minwax pencils, one lighter for holes in the light finish area of the board and one for the dark finish area of the board - matching the color of the area wherever the screw hole is drilled. The Minwax filler has held up fine also. My application was not perfect, could go back and put in some more screws, but overall, this screw kit took care of 90% of my hardwood floor squeaks. I decided at that time that I wasn't going to go crazy and drill/install a bunch of screws in one concentrated area. I could try that, but there was such an improvement in the squeaks, I decided to stop at a certain level of satisfaction. Thought about starting a business with this method, but homeowners are so picky, I really didn't want to get into all that. Some homeowner might try to get a free floor finishing job out of me if the job was not absolutely perfect. The kit I bought has screws for where the drill hole is directly over a floor joist and for holes in open areas (not directly over a floor joist). You can check to see if you've drilled over a joist or not by dropping a straightened paper clip into the hole. If the hole is deeper than the length you drilled then you know you have not drilled into a joist. I used the appropriate screw.

@jlv3x

2 жыл бұрын

Thanks for detailed info about the different sized screws and if they're over a joist or not.

@Unfinished_sentenc

2 жыл бұрын

@@jlv3x I agree. This video explains a lot. I certainly don’t know which parts are over a hoist or not, but now I do.

@Unfinished_sentenc

2 жыл бұрын

Can you use the paper clip method over carpeted wood floors? Thank you for your help.

@OGCJ10

2 жыл бұрын

Where did you buy this kit from?

FYI to anyone who wants to try this. YOU NEED TO SCREW INTO THE FLOOR JOISTS. The reason he needed so many screws is because he wasn’t screening into them. The squeak you hear normal comes from the middle of two joints. Intuitively you think that’s where you need to screw in… THATS WRONG. The noise comes from that area pushing out the nails on either side… where the joists are. When you screw into both joists surrounding that squeak, the noise will be fixed

@elcharro7403

8 ай бұрын

100% true

I have had a squeaky floor. I have not used snap screws as I have not had them. I used regular wood screws which I used on tasmanian oak wooden floor. In my case screws did not help. What helped is go under the floor measure distance between the beams. Cut plywood 17mm thickness 1 cm less then the distance between the beams and glue it with epoxy(you can use any good glue I just tried use epoxy) and put 5 screws 25mm to hold it untill it cures. I removed screws few days after epoxy cured. That's it. No more squeaking after that in that concrete place. With screws I only made the floor looking bad as the heads visible. I had to hide them after. Do not do my mistake. The screws do not work. I even put 2 screws onto floor board on each bearing it made slighly better but doesn't solve the problem. Gluing plywood from the bottom really helps. In my case the squeak was caused by wood planks but not the nails. I'm pretty sure as I was sitting on my knees pushing down by whole my weight 85kg the floor board and using impact wrench was running 40mm screws into 19mm tasmanian oak floorboards. The beams also were made of some hardwood, I pushed the screws 1mm deeper the surface. That did not work well. Now I'm struggling hide those screws. I do not think that snap screws would help in my case.

Thanks for getting straight to the point & explaining everything so clearly.

@LongologoProductions

3 жыл бұрын

@Mo Poppins: Thanks for the kind words!

This worked like magic for me. I bought the same kit u mentioned in the description. I had hardwood floor with horrible squeak that could wake up dead.. just put these 4 screws in.... can't believe it could be that easy..

@LongologoProductions

2 жыл бұрын

@Inderpal Singh: happy to learn that it helped! Great news!

i tried ages to get rid of squeek flooring, when i lifted the flooring up i found a mouse trapped, and it was squeeking from pressure etc it was so happy to see me, i gave it some cheese and warm bath and sent him on his way.

@daughterofzion778

2 жыл бұрын

🐭🔫

@charliebrownsdad178

2 жыл бұрын

lol

@deebodigital

2 жыл бұрын

😂

@redx11x

2 жыл бұрын

Your a kind hearted man

@CavanalK5

2 жыл бұрын

Well this guy just shot the little guy full of nails. Guess it did him in. The squeaking ceased.

Worked perfectly to fix the squeaks in on my floor with carpet. Instead of using the black took I drilled the nails deep into the floor and topped off hitting the head with a hammer. Easy, peasy. Thanks for the video.

@LongologoProductions

Жыл бұрын

@PM Channel: Thanks for commenting!

@lauradaniel2492

Жыл бұрын

Im definitely going to try this. If someone is looking that hard to see the holes, they dont need to be in my house. The squeaking is much more annoying.

@PMChannel.

Жыл бұрын

@@lauradaniel2492 I know right!!!

I have sampled the various tones that my squeaking floor makes and use the samples (with some processing) as percussion sounds in some tracks.

@LongologoProductions

2 жыл бұрын

@Piktor Music: That's cool -- the one good thing to do with a squeaky floor if you don't get rid of the squeaks!

@brandonmason388

2 жыл бұрын

I’ll have to try this!

Thank you my guy. I just did this on my staircase squeaks and it worked like a charm.

@LongologoProductions

2 жыл бұрын

@kasun611: Great! Glad it worked for you!

Nice, I'd rather have a floor with few small holes in it than having a squeaky floor. Thank you for sharing

Great vid, thanks dude. So many haters... everyone wants to act like they somehow know the objectively-correct or objectively-best way to do everything... I bet if you did bother to locate the joists before drilling the holes, you'd get comments like: "Why are you wasting your time finding the joists?! Just quickly put a few of these screws in the general area and the squeak will go away!" lol

@LongologoProductions

Жыл бұрын

@Daniel Alel: Right on! Thanks for the comment! 😁

@BrettonFerguson

Жыл бұрын

Also some houses have a sub-floor under the hardwood. Considering the boards in this video don't all line up where joists would be, I think there is a good possibility it has a sub-floor. If the squeak is occurring between the hardwood and the sub-floor and not by the joist, then putting screws in the joist will not help. While the perfect video in a Utopian society would have mentioned all these and other things, I don't see any of these other a**holes making the perfect squeak fixing video either. Also, most people who look up how to fix things on KZread will watch multiple videos before attempting to fix the thing. Between the different videos, they get all the information they need.

BEWARE ANYTIME YOU DRILL INTO YOUR FLOOR YOU HAVE THE POTENTIAL TO HIT ELECTRICAL LINES. AS AN ELECTRICIAN I HAVE SEEN IT TOO MANY TIMES.

@junespiritu3234

2 жыл бұрын

Thank you for that very important piece of information.

@in2indies333

2 жыл бұрын

Idk how you would hit electrical wires in a residential home. Power is at the breaker box which is mounted on a wall near the exterior. Everything else runs off of that and is run into the Attic and down the walls. Unless you have a receptacle mounted in the floor which you see in some homes you shouldn't have wires under the House

@Mycooloriginal

2 жыл бұрын

@@in2indies333 if you have a crawl space there could be.

@paulwilson2204

2 жыл бұрын

​@@in2indies333 2nd level of the house would have some wires in the floor.

@Mikewhitlock8113

2 жыл бұрын

@@in2indies333 u cant be serious 🧐

This is great, thank you. I think I'm going to share this with my landlord to get permission to fix our floors. We have the same floors as you have, so this is perfect.

@ahmctech104

2 жыл бұрын

Dear landlord, I tried something I saw on KZread and drilled into a water line. Sorry.

@openbookhardwoodfloors3882

2 жыл бұрын

@@ahmctech104 THAT MAY HAPPEN INSTED OF HAVE MANY HOLES ON THE TOP OF THE FLOOR WAT I DO BEST WAY IS GO UNDER THE HOUSE AND SECURE THE SUB FLOOR WITH GLUE AND SCREWS MUST OF THE TIME IS FIXED

@valleygirl5943

Жыл бұрын

Yep..hope they allowed. I have wanted my apartment manager to understand how the SQUEAK in apartment floor above me could in fact be resolved as shown, having driven me nuts. If she would have had to experience daily herself, it would have been taken care of. 😏

This is great! I’m gonna do the same to fix a super annoying squeak in my mud room.

Why are you using the dark wax on the light plank ? You can mix colors to blend areas to near perfection.

Put a little wipe-on-poly on the rag. It helps disolve the excess wax and matches the sheen of the surrounding area.

I went ahead and got those screws…It works very well!!! Thank you for sharing the video with us.

@stellaliang3067

2 жыл бұрын

Would you please share the link where you got these nails? I am not sure what kind of floor I have, do you think that works for all floors?

Man love this video will try these screws and stops these stupid squeaks

Very cool & helpful! Appreciate you for taking the time to teach!

Must be an older floor. Very fine looking Oak ... do not see many like that. I have a craftsman home built in 1939 . The floor looks similar ...

Helped me big time! Big thanks and thumbs up to you :) (I just screwed in 15 to 20 full girthier screws to fix 4 squeaking parchment pieces - did not care about messing up the looks as it will be covered by a rug anyway)

@LongologoProductions

2 жыл бұрын

@Edd M.: Wow! Glad the noise is gone (and that there will be a rug!). Thanks for the kind words.

Good enough, now back to life! Thanks

Excited to try this HUGE THANK YOU for sharing!

straight up wizard. thx for this. I don't have a basement. I'm on blocks. And I'm not able to squeeze underneath the house in the darkness looking for the right spot to tighten. Fuck that. This is brilliant.

You really should screw into a joist if you cam, but if you can't find a floor joist, you can use 11/4 pocket hole square-recess screws. Use a brad point drill bit the same diameter as the screw head and drill down slightly deeper than the screw head, then, in the same hole, drill down only through the hardwood just short of hitting the underlayment with a bit matching the size of the screw shank (these screws have about a 3/4" long smooth shank just above the threads). Then run your screw in until it seats snugly. The head should be slightly under flush with the flooring. Walk around and see if the squeak is silenced, if not you may have to tighten the screw a bit more. I fill the hole with a light colored wood putty until not quite full, allow it to dry, then camouflage the wood putty with artist's magic markers and seal with a drop of clear sealer. This method only works on 3/4 hardwood planks.

I don’t even have hardwood flooring but the video was good

Screw into the darker sections of the wood if possible. The wood filler will be much less noticeable

@spikefivefivefive

2 жыл бұрын

Use multiple filler colors.

I really appreciate you listing the items and order info

@LongologoProductions

Жыл бұрын

@PS Matthews: thank you and glad it was helpful.

OMG you save my life, i m not able the hear the sound, i will try your hint

Blend-Fil is ok, but eventually it will wear away b/c it's basically a crayon, as you note. Minwax tinted wood filler is an excellent and permanent alternative.

@samsngdevice5103

3 жыл бұрын

Check out wood wise patch. Used by the professionals.

@acaflooring

2 жыл бұрын

@@samsngdevice5103 still needs to be sealed wood wise will wipe out with a damp rag

Thank you for this excellent tutorial!

A buddy of mine went into the basement under his house and screwed upward. No holes on top. Not sure how he and his wife did this but it worked way better than drilling holes on top of the wood 60 year old hard wood floors.

@LongologoProductions

2 жыл бұрын

@EL34XYZ: it’s in other comments somewhere, but yes, if you do have access from beneath the floor that it obviously way better than having to drive in screws through the finished floor. In this video, however, it’s an upstairs room so no access from below, and the area would be covered by a rug anyway. You have to do what works best for your situation.

Best helpful video I’ve seen here!

@LongologoProductions

3 жыл бұрын

@melinageofashion: Thanks!

SO TO THE POINT! Awesome video!

@LongologoProductions

Жыл бұрын

@NY: Thanks!

I have carpeting in my rental but I want to fix these squeaking issues. Its everywhere and its so annoying. But I do not know what's under the carpet. I have to see if I can even try to remove the carpet to fix it. Thanks for the video.

@LongologoProductions

2 жыл бұрын

@Dee M: This can be done through carpet if you know what is underneath. (See the three-prong metal guide near the beginning of the video.) Perhaps ask the rental owner - they may be able to tell you. Good luck.

Did you consider drilling a slightly smaller hole and using a long, trim screw (typically using a Torx bit). These screws have very narrow heads that don't split the flooring, if the proper size drill is used to pre-drill the hole. Trim screws are designed so that you can drive the narrow head of the screw just under the top surface of the floor, but the head puts enough pressure on the sides and bottom of the pre-drilled hole to hold the floor board in place. With a 1/8" hole drilled into the floor, and the head snapped off, there's not much of the screw left to hold the floor board down and stop the squeaking.

@LongologoProductions

2 жыл бұрын

@Anonymous98: An interesting thought for sure. However, I also used a 1/8” drill bit for the screws used in this video. The screw heads don’t go all the way down, rather, they snap off at a scored part of the shaft. That scored part breaks off just below the surface of the floor. I think this is no wider than the option you describe. But still it is something else to consider. Thanks for commenting.

Me personally, I'd just live with the squeak. If it was one nail, fine, but to put 6 or 7 in one small area stops the squeak but leaves clear circular markings, so it's a case out out of the fire and into the frying pan. As for the video, I appreciate you showing us how it's done with that screw breaker gadget.

That’s awesome. Can I do that on stairs covered with a carpet?. Thanks for sharing 👍

@LongologoProductions

2 жыл бұрын

@Adan Arceo: Yes; yes you can. Near the beginning of the video I show the tool to use over carpet. Thanks for the kind words!

Wood glue works good to for a filler 👍✌️

I melt my crayons with a lighter and you don’t see the filler at all.

You can choose a color based on the wood color where the hole is and make them invisible.

I would have used saw dust to fill in the holes (with some type of glue)

@BrettonFerguson

Жыл бұрын

I've done that several times. When I didn't have any wood filler I used Wood Glue and saw dust. Also on drywall and plaster to fill nail and screw holes, When I didn't have any plaster, I've used Elmer's Glue and a small piece of toilet paper balled up. After it dried and I painted you couldn't tell there was ever a hole.

absolutely great tutorial.

@LongologoProductions

2 жыл бұрын

@DegenWoW: Thanks very much!

Appreciate your help on this!

@LongologoProductions

5 ай бұрын

@pizzanpepsi: Glad to know it helped!

I'd rather have the squeaking than drilling holes all over the floor myself.

@LongologoProductions

2 жыл бұрын

@Billy Ellis: Definitely not for everyone.

@SirDrago

2 жыл бұрын

I was thinking the same thing.

That's Ludacris

How will the wood expand and contract in changing humidity?🤔 I think this floor will have more problems in the future

@LongologoProductions

2 жыл бұрын

@rentatent85: How? The wood will expand when it absorbs moisture, as would occur in a high-humidity season like summer along the U.S. east coast, and will release that moisture during dry months like over winter. Although this may primarily occur from below the floor, assuming the top surface is sealed/coated. Depending on where you live and how consistent you keep your home temperature and humidity, you will notice that some squeaks may come and go with the season. Save this project for those really annoying squeaks that outlast several seasons and justify drilling a hole(s) into your floor.

I need to do that,thanks for the video

In the case of the hardwood plank..you don't have to hit the joist as you are screwing the hardwood to the subfloor... In the case of carpet...the subfloor needs to be screwed to the joist and the directions tell you how to do it....

@martinl470

Жыл бұрын

Hello, i have a area in my hallway that does not have open access to screw from below in my basement because it was sheet rocked. I wanna use the above method with drilling. You said you dont need to hit a joist? With the other area in my kitchen where i have squeaks, i had to drive screws straight through the subfloor into the hardwood planks to get the squeaks to stop. I tried glue, 2x4’s, shims, nothing stopped the squeak until I drilled directly in the subfloor into the hardwood planks.

The lo doesn't mean low torque it's actually more torque but less speed

@LongologoProductions

3 жыл бұрын

@nightmare in action: You are correct -- I misspoke. At 0:45 I should have said "low speed" setting. Thank you for catching that.

Great work 😁👍😎

Very nice!

looks like when you use the guide the holes are smaller. Must be when you bend the screw to snap it off makes the hole less clean. My floor has so many squeaks.

@LongologoProductions

2 жыл бұрын

@STRIKER YYC: The holes might have a *slightly* smaller diameter when using the guide, because it does facilitate 'snapping' the screw at the score markings and allows you to mostly just lift straight up to remove the upper portion of the screw. But in terms of noticeability of the filler in the hole I found that it really doesn't make that much of a difference so I have opted for the expediency of skipping use of the guide when I know there are going to be several screws needed, or when, as I mentioned in the video, the screw still does not fully "snap" off even when using the guide. However, as you noted, bending the screw back-and-forth to snap it off (when inserted without the guide) will inevitably push some of that wood away at the surface of the floor--just not by much if you're careful. Good point to consider nonetheless. Thank you!

Great thank you

So, what is the alternative? Tearing up all of the floor or would you be able to maybe get just the pieces up where the squeak is and replace them with new panels? I've got vinyl and I'm not sure if it would be easier to pull some of it up and fix the wood down underneath.

@LongologoProductions

Жыл бұрын

@Matt Liston: If possible, you could access the floor from underneath, for example an unfinished basement. Then you could take care of the squeak from below without putting holes in the floor from above. But that’s not always feasible for example like in an upstairs bedroom but having a finished ceiling on the first floor directly below. I definitely would not put holes in vinyl using the squeak-no-more kit.

@OngoGablogian185

Жыл бұрын

@@LongologoProductions Thanks, mate. Yeah I'm a flat with another family below me. The squeaks are pissing me off but I think it's maybe better to wait and fully soundproof the floor and replace the vinyl then.

The only problem is how long is the screw have to be because how do you know you're not going to bottom out into the concrete because all you have is 1/4 inch underlayment

@acaflooring

2 жыл бұрын

this is for flooring not on concrete but over crawlspace with wood joists

And what happens if the screw snaps higher than the laminate..how do you get the screw out with no head on...

@LongologoProductions

2 жыл бұрын

@Andrew Turnbull: If that happens, I would first try using a small screw extractor kit with the drill to back out the screw. You can get these kits on Amazon. If you’re not comfortable doing that, you could use a Dremel with an appropriate grinding head to (very carefully - because one slip and you will scratch the hell out of your floor!) remove the portion of the screw that remains above the level of the floor. Or, you can use an appropriate size nail punch and hammer to just pound the protruding portion of the screw shaft down below the level of the floor. Wear safety glasses when doing any of these because of the chance of metal fragments getting kicked up!

You always want to nailed or screw in the grain. It hides the holes better

@LongologoProductions

2 жыл бұрын

@Moices Mendoza: Good point to make strategic use of the natural grain variation to help hide the holes.

Nice work looks like he missed the electrical great video

@in2indies333

2 жыл бұрын

Lol. Give me a break. What electrical wires are running under the floor? Maybe if he was next to the breaker box. The majority of wires are run in the ceiling and down the walls not under the floor. Unless a specific appliance is installed.

Ah, I see another contractor whom doesn’t care about the quality of his work installed the sub floor half assed.

This is NUTS!!!

Time for me to start doing this all over the house, tired of the squeaking

Why not use a finish nailer smaller hole and not even noticable

Amazing. Do you happen to be in NYC anytime soon? I’ll hire you to do this for me 😂 Question - can you do this for any floor boards that are lifted? Just moved into an apartment with gorgeous hardwood floors, but some pieces seem to lift up a tiny bit

@LongologoProductions

2 жыл бұрын

@Claudia Rodriguez: 🤣 Lifted boards could be secured to the subfloor but I would be very careful because it could be a symptom of larger problems. See www.discountflooringdepot.co.uk/blog/2016/10/wooden-floor-lifting-heres/amp/. See also www.woodandbeyond.com/blog/common-solid-wood-floor-problem-bulging-and-lifting/?amp

If I had a concrete screed under the wood, would this screw be fine? I have a floating interlocking wooden floor, with a PVC carpet underneath and then the concrete base

@jaywebster2125

2 жыл бұрын

You don’t wanna screw into concrete

@en.guard.463

2 жыл бұрын

@@jaywebster2125 sure

Thanks for sharing.

Using different color fillers will mask the holes even more.

@LongologoProductions

2 жыл бұрын

@spikefivefivefive: Indeed. I noted that different colors can be used - see the description of the video and see around 5:38 in the video.

If you screw near the floor joist you moght not need as many screws

@LongologoProductions

2 жыл бұрын

@R: Sometimes that works but not always. This was unfortunately one of those times…

Great i will try it.

You might hit the electrical wires or pipes if you go that deep

@LongologoProductions

3 жыл бұрын

@Tung Nguyen: Always be careful where you are drilling. See other comments too.

can I use this on condo wood floor?

What’s the name of that tool you used as a fixture to break the screw in half. I have many squeaky areas in my home. Thanks in advance

@LongologoProductions

3 жыл бұрын

@JerFurk Spitszer: There’s a link in the description below the video for where to get the tool.

@supah_sonic9979

3 жыл бұрын

Thanks. Found it on Amazon

What kind of screws did you use? I did not hear you mention them. So excited about this! Will be fixing my squeaky floors soon!

@LongologoProductions

2 жыл бұрын

@Gabriela Maurier: The screws and other items are shown at 0:05. Also, I included a link in the description. And extra screws are part #3251. Good luck!

@psychakilla

2 жыл бұрын

did you end up fixing your floors?

@LongologoProductions

2 жыл бұрын

@@psychakilla : Yes - still as good as shown in the video.

My floors make a cracking sound when I walk on them. Any idea what that is? Just age? Its annoying...

@LongologoProductions

2 жыл бұрын

@Tkeyah Nicole: It could be a number of things. Floor boards against subfloor, or floor boards against floor boards, or floor boards flexing due to a gap underneath, etc. Hard to be sure without seeing/hearing/feeling them….

This has not been on the market for a long time, long enough to let a huge population to not be familiar with this. I used this many years ago, used multiple screws and did not stop the squeaking. What I did not know was the danger of hitting pipes and electrical. Thank goodness I avoided that hazard.

Cables / pipes could be a serious issue !!

You can leave it as-is for that unique drive-by-shooting appearance 😮

Question, I have a carpet over the hard wood floors, do I need to find floor joice to use this or can I just screw in like you did without carpet

@LongologoProductions

2 жыл бұрын

@Juddone1: In the early part of the video, I show the related tool for use going through carpet (it’s the one with the three spikes). Before screwing into anything, make sure to walk around the area to listen for noise and also to feel for any flexing of the floor. (I realize this may be difficult on a carpeted floor.) It might also be helpful to have another person to stand on or over the area of the squeak in the floor while you walk around adjacent areas to listen for whether the squeak moves or not. This can help you isolate where to place a screw or screws. Good luck.

Can this product use on engineered wood?

Watched this video, did this to my floor, there is still squick plus now I have bunch of whole on my floor, he should've mentioned first find the floor joints and then put those screws, otherwise it doesn't make any difference!!

@LongologoProductions

Жыл бұрын

@Ben Shojaei: Often, but not always, the floor joists. It makes a difference when the squeak stops. And if you watched the whole video, you’ll note I wasn’t particularly concerned about the holes or color matching since I was going to have a rug over it anyway. YMMV.

Can you sand and stain floors after doing this method and applying the pencil?

@LongologoProductions

2 жыл бұрын

@WestCircleBitchez: Yes, but I would not use the pencil-type filler in that situation. I would instead use a regular wood filler that hardens and can be sanded/stained. Then when you are done sanding, staining, and poly/protective coating you shouldn’t be able to see anything. Good luck!

Will these screws work on laminate floor? We recently put new laminate floor in kitchen but the board underneath is starting to squeak alot

@LongologoProductions

Жыл бұрын

@ngawang Paldon: I would not use this on laminate.

Do they make them for headboards?

@LongologoProductions

3 жыл бұрын

@Joseph Robison: 🤣

Thanks for the video! Would you recommend doing this before we sand our floors or after?

@LongologoProductions

2 жыл бұрын

@christopher halloran: definitely after but before refinishing.

@jamiefisher8411

2 жыл бұрын

Exact question and answer I was looking for, thanks gents.

In the video, you made few holes, but you did not put any screws to the holes r before you fill the them with the Winmax wood filler.

@LongologoProductions

2 жыл бұрын

@Huaping Luo: At about 1:30 you’ll see putting in one of the screws. For brevity, I did not show drilling and inserting the screw for every single hole although I explained it verbally in the video.

How thick is the underlayment?

The ceiling is exposed in the basement, can I just do this from the bottom?

@LongologoProductions

2 жыл бұрын

@Hapablap: Yes. This is discussed in some of the other comments. Also, you wouldn’t need screws this long. It would be much better to work from underneath if you can do that. In this video, I’m in an upstairs bedroom and the floor will be covered with an area rug. It was better for me to do it this way than to cut a hole in the ceiling below on the first floor.

A better way would be to find the joist normal they are 16inch apart for better results less holes and try not to create the holes on the soft grain.

@LongologoProductions

2 жыл бұрын

@Juan Guido: Definitely work directly over the joist if possible. However, the example in this video is an egregious squeak in between joists. Sometimes it can’t be avoided. But yes: less holes are better if possible.

Does the crayon harden

@LongologoProductions

Жыл бұрын

@mtn dew: maybe a little bit over time but still softer than the wood.

My house was built almost 100 years ago... My entire floor is about to be screws... Which I might just deal with the squeeking because you can absolutely still see that there are giant circles filled with wax in that floor...

@LongologoProductions

2 жыл бұрын

@Sgt Nooodle: 😅😂🤣. I know what you mean….

Can you pls tell me, if I put laminate on top of the squeaky wood floors, wd they still be squeaky? Or I have to fix the squeak 1st and then put the laminate?

@LongologoProductions

2 жыл бұрын

@Emilia Manda: Definitely have to fix the squeaking first.

@EmiliaManda

2 жыл бұрын

Thank you !

Thank you for this!

So you did not have to hit a floor joist?

@LongologoProductions

2 жыл бұрын

@juddone1: some people say you always have to be over a floor joist, but that’s not always the case in all situations.

I need to do this but my problem lies with my floors extremely high gloss finish (wet look). Hiding the patch would be nearly impossible. Ideas?

@LongologoProductions

2 жыл бұрын

@SharpEdgeStandard Official: that’s a tough one. What about using a more traditional wood filler that hardens (instead of the soft wax I used in the video) and then using a stain pen or something to match the color. For the high gloss / clear finish, you could use a tiny paint brush (like for painting plastic models) and lay down the tiniest amount of the high gloss clear coat on top? It would be extremely tedious but it would be precise if you were concerned about visibility. However no matter what it won’t be perfect like the original. How old are your floors? Any existing nails in them that are visible under the gloss?

@SharpEdgeStandardOfficial

2 жыл бұрын

@@LongologoProductions hi. They’re Bruce 2.25” installed in 2001. Basement is fully finished with drywall ceiling so can’t see underneath otherwise if fix from below. No visible nails or screws under finish, it’s tongue and groove install.

@LongologoProductions

2 жыл бұрын

@SharpEdgeStandard Official: But you CAN access it from underneath! Given the high gloss finish on the floor, it would be so much better to just cut out a small piece of the basement drywall ceiling and take care of the squeaking with some shorter regular screw(s) from below. It sounds like you have an identified area of concern for squeaking. You could measure out from two walls to note that area, and then repeat the measurements in the basement directly below so you will know where to cut out a small piece of the drywall ceiling. And before you start inserting some screws, you could have someone else stand on the floor from above and flex it to make sure you hear the squeaking directly below. Then, with that person standing still with their weight on the area of the squeaking, you should be able to run in one short screw or a few short screws from below to take care of it. After that, wait a couple of weeks to make sure the squeak is gone to your liking before you repair/paint the drywall section. So, unless your basement ceiling drywall has some stucco or textured pattern, I really think it would be so much easier/better to repair a small drywall hole and repaint that part of the ceiling. After all, it's just a basement. Worst case, you get frustrated with a few drywall holes in your basement ceiling. That would be a better alternative than being frustrated with holes in your high gloss floor that you may never be able to perfectly hide.

@SharpEdgeStandardOfficial

2 жыл бұрын

@@LongologoProductions very true. Thanks for the insight I’ll probably just do as you suggested. Thanks and stay safe my friend.

Would you recommend doing this before or after sanding and refinishing hardwood floors?

@LongologoProductions

2 жыл бұрын

@Mayte Bautista: definitely before! Then you can fill any holes with a traditional wood filler, do your sanding, and then refinish without having to worry about matching filler in the holes to an already stained /finished floor.

@Maytebayy

2 жыл бұрын

@@LongologoProductions thank you!!

@vinniscarboni4095

2 жыл бұрын

Don't do it

Is it not necessary to find the joists underneath?

@LongologoProductions

2 жыл бұрын

@Ese Snoopy: It can be helpful in some situations but not necessary in all situations.

I’m having a hard time understanding why are you screwing those screws 😓😫… can someone explain to be how that works? 🙉… I have a few areas that I would like to repair 🙏 thank you!!!!

@snetsab

2 жыл бұрын

Arcelia, The part of the screw that remains after breaking off the head of the screw has the thread imbedded in both the board and the joist underneath it. The thread of the screw ensures the board and the joist remain in a fixed position without any movement in the board when someone walks over it. Try screwing two pieces of wood together and you will get the idea.

@arceliaherrera663

2 жыл бұрын

@@snetsab ok, that makes sense. Thank you!

I drove the drill bit in fine, but when I tried drilling the special screw through the fixture it won’t go all the way down. Any advice?

@LongologoProductions

3 жыл бұрын

@C C: back the screw out, and then take a long thin nail and see if it will go into the hole and further than the screw goes in. If it doesn’t, you may have an obstruction immediately below the hole that you drilled.

@robertplummer5015

3 жыл бұрын

No..the screw is designed to only alow the threads to enter the flooring and into subfloor/joist... Then you 'snap' off the head of the screw with the tool provided. That allows for a wood filler to hide the hole that was drilled...

After you were done were the wood boards all even with each other

@LongologoProductions

2 жыл бұрын

@Brian Hansen: Yes. All even with each other.

@1718HULK

2 жыл бұрын

@@LongologoProductionsthank you