DIY Extension Mechanism for extendable table using drawer sliding channel
Жүктеу.....
Пікірлер: 20
@TweetyMae-br2yu5 ай бұрын
I’m excited to do this! Exactly what I need for a diy table bookcase!!!!
@kathleenelaniejames80837 ай бұрын
The exact video I am looking for! Thank you thank you thank you!!
@TweetyMae-br2yu5 ай бұрын
Thank you! 🤗
@s.zander62115 ай бұрын
Thank you. 😊 Is it even possible to put a strain on this in the long run? Is quite a lot of weight due to the additional plates and the place settings....
@johnburns2940 Жыл бұрын
I enjoyed this video. I liked how the music was beautiful. It's a grand idea. You did a mock up table to test the mechanism. Very nice. I can use this idea. This looks very good. Did u build the table. That would be interesting adding more and more leaves over time 😄
@smartmadehome
Жыл бұрын
Glad you enjoyed it! Yes I built the table as well. Its in another video.
@papa-dt1cv Жыл бұрын
Where to buy?
@Danielajtoro Жыл бұрын
Hi! Any way you can install these without drilling?
@smartmadehome
Жыл бұрын
I guess not. Any tape or glue won't be able to bear the weight.
@denissumikaela11 ай бұрын
What's the length of the slider mechanism that you used?
@smartmadehome
11 ай бұрын
I used four pairs of 16 inch telescopic channels. In extended form it spread out to 80 inches.
@gsmash0012 жыл бұрын
Hi.can you make a DIY recliner mechanism
@smartmadehome
Жыл бұрын
That would be really great if I could. Have to ponder over it.
@KanrApocalypse2 жыл бұрын
How long are the bolts you used to connect them?
@smartmadehome
Жыл бұрын
5 mm. But I would suggest to test with multiple sizes. It would depend on thickness of your sliding channel.
@viking442696 Жыл бұрын
How much weight can it take?
@smartmadehome
Жыл бұрын
I had put around 12 kg. Haven't tested more than that. Channels are usually capable to bear much more than that, but joints are week points. I even considered welding channels together. Haven't done that though.
Пікірлер: 20
I’m excited to do this! Exactly what I need for a diy table bookcase!!!!
The exact video I am looking for! Thank you thank you thank you!!
Thank you! 🤗
Thank you. 😊 Is it even possible to put a strain on this in the long run? Is quite a lot of weight due to the additional plates and the place settings....
I enjoyed this video. I liked how the music was beautiful. It's a grand idea. You did a mock up table to test the mechanism. Very nice. I can use this idea. This looks very good. Did u build the table. That would be interesting adding more and more leaves over time 😄
@smartmadehome
Жыл бұрын
Glad you enjoyed it! Yes I built the table as well. Its in another video.
Where to buy?
Hi! Any way you can install these without drilling?
@smartmadehome
Жыл бұрын
I guess not. Any tape or glue won't be able to bear the weight.
What's the length of the slider mechanism that you used?
@smartmadehome
11 ай бұрын
I used four pairs of 16 inch telescopic channels. In extended form it spread out to 80 inches.
Hi.can you make a DIY recliner mechanism
@smartmadehome
Жыл бұрын
That would be really great if I could. Have to ponder over it.
How long are the bolts you used to connect them?
@smartmadehome
Жыл бұрын
5 mm. But I would suggest to test with multiple sizes. It would depend on thickness of your sliding channel.
How much weight can it take?
@smartmadehome
Жыл бұрын
I had put around 12 kg. Haven't tested more than that. Channels are usually capable to bear much more than that, but joints are week points. I even considered welding channels together. Haven't done that though.
How to purchase?
So how many 🪑 does that fit?
@smartmadehome
Жыл бұрын
Upto 8.