DIY Blacksmith Block Brush (how to make)
Blacksmith Block Brush or known as Butcher Block Brush is a tool that is used in blacksmithing for quickly and effectively removing the forging scale on a piece of steel when it's being forged.
So as the title says I'm gonna show you how you can actually make one for yourself.
have fun.
My Instagram: / apurak.co
Feel free to contact me if you want to say something, I will get back to you.
Thank you for watching!
Masoud
Пікірлер: 35
This past Sunday someone at my blacksmith group was talking about this same video. I meant to look it up and forgot, then lo and behold, it just pops up in my feed! Looks time consuming, but a simple concept - very awesome! You got my subscription.
@Apurak
2 жыл бұрын
thanks for your awesome feedback my friend
Oh you beat me to it! Nice video!
@Apurak
2 жыл бұрын
glad you liked it ☺️
Awesome 😍
@Apurak
2 жыл бұрын
thanks man
Very nice!🍻
@Apurak
2 жыл бұрын
Thanks! 👍
Apurak ki jaya
Excellent
@Apurak
2 жыл бұрын
Thank you so much 😀
خسته نباشید خیلی خوشحالم که از این هنر تولید محتوا میکنید
@Apurak
2 жыл бұрын
سلامت باشین،خیلی ممنون
An adjustable bristle length is needed when blacksmithing. This can be achieved by adding another layer of wood with holes drilled as holes previous spacing and leather straps each end. this extra wood then can be raised for softer or lowered for a more course brushing strokes.
Nice
@Apurak
2 жыл бұрын
Thanks
خیلی عالی
@Apurak
2 жыл бұрын
مرسی حمید جان
@hamidrahnama9322
2 жыл бұрын
@@Apurak مخلص
عالی و خیلی مفید بود یه سوال داشتم این فنر چیه ؟از کجا تهیه کنیم؟
@Apurak
Жыл бұрын
فنرِ سیمکشی برق ساختمون هست، فروشگاه های لوازم برق برای فروش دارن.
Where did you get the Spring wire I've been searching all over the Internet and I can't find it I think I'm just stupid but still how did you get it
@Apurak
2 жыл бұрын
you're not stupid my friend, I had the same problem but I finally figured it out. in my country this kind of spring wire is used to pass electric wire through the wall you should look for it in electrical supplies.
@BurntMushroomBlacksmithing
2 жыл бұрын
Enough bailing wire might do the trick. Though it would probably be mild steel, and might wear faster than these spring ones. Get thick stuff and only use it for hot work? 🍻
@Apurak
2 жыл бұрын
@@BurntMushroomBlacksmithing if you use bailing wire it would bend at the first touch. it should be some kind of spring wire.
@nathanheng8954
2 жыл бұрын
www.thespruce.com/what-is-a-fish-tape-1152557 Heres what you need if you didn't find it yet.
@EduardoSVA
2 жыл бұрын
@@Apurak Great idea! I made one brush for me, but I usedSteel wire: the brush got so heavy that I have to rest after use it! Greetings from Brazil!
What is the size of the spring steel used ?
@Apurak
2 жыл бұрын
the cross section is 1*3.5 mm , but it could be anything close to this size. the length of the wire is also optional, depending on how soft or harsh you want the brush to be like, I picked about 12cm each, so when i bent them in half it would be 6cm, and 2cm of it would be in my first wood block, so I end up with 4cm of wires that sticks out of the block.
@teun7923
2 жыл бұрын
@@Apurak Thank you for the response!
@Apurak
2 жыл бұрын
@@teun7923 my pleasure
For what this brush
@Apurak
Жыл бұрын
it's for removing the forge scale when you're forging steel
@all4tech738
Жыл бұрын
@@Apurak ok thnaks