tp4056 1w led 2x 2000mAh battery A1019 *10k resistor are connected to transistor base, but without resistor, LED light brighter
Жүктеу.....
Пікірлер: 267
@TheGrkBoy Жыл бұрын
This panel can put out close to 100 watts kzread.infoUgkxOqI2yqX0XVrhR2BMJciTWrHJpG8FhJyg when positioned in the appropriate southernly direction, tilted to the optimal angle for your latitude/date, and connected to a higher capacity device than a 500. The built in kickstand angle is a fixed at 50 degrees. Up to 20% more power can be output by selecting the actual date and latitude optimal angle.The 500 will only input 3.5A maximum at 18 volts for 63 watts. Some of the excess power from the panel can be fed into a USB battery bank, charged directly from the panel while also charging a 500. This will allow you to harvest as much as 63 + 15 = 78 watts.If this panel is used to charge a larger device, such as the power station, then its full output potential can be realized.
@Kleponturbo3 жыл бұрын
This is correct pin for A1015 : OUT+ (emiter/pin1), LED+ (collector/pin2/middle), IN+ (base/pin3)
@zulkarnainzamin1183
3 жыл бұрын
meaning?
@arazmamedzade81104 жыл бұрын
Collector max Current: -0.15 A for A1015 transistor and current of 1W LED is: 1W/3,3V= 0.3A. We have to add resistor(may be 10-12 Ohm) between collector and anode pins. It"ll be save LED"s life (and battery, too).
@ronaldd.1355
4 жыл бұрын
Why do you need a resistor? in my calculations it is not needed. The batteries when full charged 'll be: 4.20, the LED is about 3.3v, so you have to reduce: 0.9v, so (0.9v / 300ma) = 3OHMS. Not 10000, Am I right?
@arazmamedzade8110
4 жыл бұрын
@@ronaldd.1355 Dear Ronald, there is such a thing as "instantaneous current value", which affects the moment the load is turned on. This current exceeds the rated current by 5-6 times. In order for the LED (load) to not burn during switching on, we take a resistor 3-4 times more. In all other respects - of course you are right.
@adrianmoone67373 жыл бұрын
GREAT VIDEO! can you show us how to change a pre-made outdoor solar security light? maybe how to make them turn on & off when we WANT instead of being motion detected? and maybe add a ?? dial if possible? to turn them up brighter or down for lower lighting? Then finally my biggest question! Is there any way to use these solar power lights for an alternative purpose? by maybe taking OUT the light, probably double up the batteries? and add a USB charger? I have 8 brand new ones, and I've already separated 3. Placed the solar on my outside & the light on my inside for motion detected lighting inside, but really they're brighter than I need. They stay going 3 days now so far with overcast! Free lighting! Yay!! (free solar phone charging would be AWSOME!
@jemarvalencia3544 жыл бұрын
I tried this and the led is not turning off when there is current from solar panel. I used A1015 GR331 transistor, whats the problem?
@alexeydudin38495 жыл бұрын
Я не парю мозг а сразу собираю подобную схему в уличный светильник вместо лампы на 220 в. Просто красиво экономично. И схема у меня сложнее с четким переключением на стабилизаторе tl431 и естественно с дополнительной бмс для 18650. А тут уж больно дешманский вариант из бокса для обеда😎
@sergeyboitsov8643
Жыл бұрын
А чём разница между тем что в видео и tl431? правильно ли я понимаю, что tl431 как раз будет включать нагрузку когда темнеет?
@jonnymorillo14843 жыл бұрын
Your 2x 1watt 6 volts solar panel are verry weak to charge 2x 2000mAh lithium battery. Cuz your 2 panel can only produce 0.333 amps of current, not much. (P/E or V=I) you do the math. And the TP 4056 will ignore it. Cuz TP4056 have a minimum accepting current of 37% battery capacity. So if you have 2x 2000mAh battery, you need 0.740amps of current from the panel to charge your battery. It means u need 5watts 6volts solar panel that can produce 0.833 amps of current enough to charge those 2x 2000mAh battery. But overall, i love the video. You work clean.
@davidgraemesmith19805 жыл бұрын
Nice tip with the nail varnish, not seen that technique since my high school years 91-96
@AlamoCityCello6 жыл бұрын
Excellent DIY Video. Very practical sourcing of readily available materials. Smart design. THANKS BRO!
@adrienrandall9483
3 жыл бұрын
You all prolly dont give a damn but does someone know a tool to log back into an instagram account?? I was stupid lost the password. I would love any help you can give me
@bowenowen5818
3 жыл бұрын
@Adrien Randall instablaster ;)
@adrienrandall9483
3 жыл бұрын
@Bowen Owen thanks so much for your reply. I got to the site thru google and im trying it out atm. I see it takes quite some time so I will get back to you later with my results.
@adrienrandall9483
3 жыл бұрын
@Bowen Owen it worked and I finally got access to my account again. Im so happy! Thanks so much, you saved my account :D
@bowenowen5818
3 жыл бұрын
@Adrien Randall No problem =)
@edmundbrisenio22865 жыл бұрын
Cool. Same as my circuits. Good Job
@cinderelladreamshop1310
3 жыл бұрын
is it working same as video? With tp4056 charger module also? Need any diode?
@hiendrianto Жыл бұрын
Mantap mas bro Creative bikin lampu solar cell nya
@christophergalero5053 жыл бұрын
What is functioning of resistor...
@zainal8512095 жыл бұрын
What's the resistor for?
@samwallin9694
2 жыл бұрын
it was not used when i made this i used a 20 ohm resistor inline with the negative side of the led and that drops down the voltage as i was worried about burn out
@HeroCP7 Жыл бұрын
This is a pnp transistor. Shouldn't the base be connected to the negative of the solar panel? Wouldn't connecting the base to the opposite polarity be causing a short? It should honestly still work since electrons move from the negative to the positive terminal so it'll eventually reach the base but still i can't help but think it is causing a short somewhere.
@ALEFILES
8 ай бұрын
Not at all. The base is connected to the right pin (+), because when the sun lights the panel, the +V of the panel _BLOCKS_ the PNP transistor, and _when the night comes,_ the voltage of the panel fall to zero, activating the transistor, and driving current from battery to the Led across the collector... Understood? Greetings from Argentina!❤
@luisfernandezm.18724 жыл бұрын
Hola...cual transistor debo usar?...a1015 o a1019...gracias
@emre-uc1zh2 жыл бұрын
Does the value of the resistor depend on the current drawn by the connected load? Does the life of the battery depend on the resistance? What is the maximum current drawn by the load in this circuit?
@ALEFILES
8 ай бұрын
The maximum current _DEPENDS_ of the maximum current the transistor can drive...If you use a small transistor, don't expect to connect a BIG led light, because you will burn the transistor...I suggest to use a BD140, TIP42C or similar, BUT REMEMBER: anything transistor you use MUST be PNP, otherwise the light won't turn on by night... It will be better If you use a MOSFET P-CHANNEL instead a bipolar transistor (e.g. IRF9640)... Greetings from Argentina!❤
@energycrafts82066 жыл бұрын
Nice but you did not show the 10k resistor on schematic or where to solder. I assume this is the base current controlling resistor?
@xlines
6 жыл бұрын
EnergyCrafts the 10k resistor is more likely for the base of the transistor.
@judeareola6026
6 жыл бұрын
kzread.info/dron/EfGr5XZvclJliyoFwT9n_g.html Check this one out.
@nikhilganguly546
5 жыл бұрын
10 k resistor should be added in the transistor b
@kalamatagames26316 жыл бұрын
you can look for cable box 10cm×10cm cost about 1 $ per box that kind of box used indoor or outside the house kind of waterproof
@phitrow4 жыл бұрын
Out battery - 4,2v. LED in 3,3-3,4v. Need resistor for stabilisation carrent LED...?
@FargothPL
3 жыл бұрын
There's no need. You're losing some voltage across the transistor. I recreated a similar project (I found where I made a mistake when I previously use his scheme) and the voltage on the diode was 3.17V (so for white LED is ok), while the battery voltage was 4.1V
@phitrow
3 жыл бұрын
@@FargothPL ok
2 жыл бұрын
Is the transistor working as some sort of current regulation there, or is the LED straight up getting the full battery voltage? If the second thing is the case, use a 3.3v regulator (if it‘s a linear one, it can still waste up to 800mW with a 3W LED but the LED will get a constant current).
@samwallin9694
2 жыл бұрын
its working as a switch it turns off the leds while the solar pannel is providing voltage which charges the batterys, but when the pannels are not producing voltage the leds turn on and use the battery voltage
2 жыл бұрын
@@samwallin9694 I know, it‘s a PNP type transistor. I just don‘t know if it has a internal resistance, because it‘s the only thing between the LED (2.6 to 3.3V) to the battery (2.6 to 4.2V).
@ALEFILES
Жыл бұрын
@@samwallin9694 How does the current flow from batteries to the 1W Led (+) lead at night? The PNP transistor turns ON when it is night? If it is, the 2SA1019 transistor doesn't drive much current, just 0.05A, and the 1W LED needs at least 0.300 A... Greetings from Argentina!
@sshutupurface8345
Жыл бұрын
i use 1k resistor with 18650 so the current is 4.2 milliamps and the led emits 0.017 watts good as night light lasts 55 days + permanently on
@amritswagatadityaraj11114 жыл бұрын
But where you have used that 10k resistor
@DigitalIP4 жыл бұрын
Clear Coating would also help with protection, instead of using nail polish etc.
@Dhirenswain776 жыл бұрын
Mine working reverse, as the panel charges the led glows. Whats wrong i did?
@rimbang_
6 жыл бұрын
Dhiren Swain yah me to
@amigoselvador2786
5 жыл бұрын
Dhiern swain same here
@omnidive3416
5 жыл бұрын
make sure to use a PNP transistor, NPN transistors turn things on when current is applied and PNP transistors turn things off when current is applied. This means that with a PNP transistor, the solar panel will give current to the transistor base, turning off the LED. When the panel is not producing power (night), there is no current and the LED turns on.
@katchupoy016 жыл бұрын
Albert. I prefer you talking on your videos. Its way better than music. Para ma explain mo nang mabuti.
@wessiez11 ай бұрын
Goodday. What a simpel and great solution for this application. Is there a way to make the LED go on when it is a bit more dark? Mine is going on very soon...
@exobox7582 жыл бұрын
Can I use any other npn transistor
@hiranukwatta7076 Жыл бұрын
great video , can you do video about 6/10w led light circuit
@electroumit3 жыл бұрын
The box is not resistant to sun. Box life is 1 or 2 year. Nice job.
@albertnario4877
3 жыл бұрын
it's enough time for it.
@solderist4 жыл бұрын
Hi, question: solar panel input is 1w/6v =. 17A. Two panels =. 34A. Is that enough to charge the battery for whole day? Or is the TP4056 can boost amp? Sorry for the question if it's stupid or easy. Thanks
@ALEFILES
Жыл бұрын
The TP4056 only DRIVE the current from the panel to charging batteries, don't boost voltage or amp...Greetings from Argentina!
@cuncunyusman69013 жыл бұрын
Where is the resistor??? 🤣🤣🤣
@markangelosegurola
2 жыл бұрын
Bro read the description
@bangladesh2365
2 жыл бұрын
10k........😂😂😂😂😂
@miteshdhanani
Жыл бұрын
@@markangelosegurola show the description
@satriyobaru9451
Жыл бұрын
what is the resistor for?😂😅😅
@desainalf
9 ай бұрын
@@satriyobaru9451for seLLing.. 😂
@jayracpan98315 жыл бұрын
Emitter should be connected to ground and collector connected to negative of the led .
@amigoselvador2786
5 жыл бұрын
could you please explain more in a simpler way thank you
@Petardozord4 жыл бұрын
Will it work with singel 5vpanel and single 18650 lithium battery?
@yavuzcan233
3 жыл бұрын
it works
@the_moto_monk_ey3 жыл бұрын
Can you double check your circuit diagram ? I made it like you showed in circuit diagram but it is not working.
@samwallin9694
2 жыл бұрын
the diagram is incorrect use kzread.info/dash/bejne/Y32C0MqOYa3Tlto.html for the correct orientation
@SantianoBe Жыл бұрын
I followed the video to a T, but still something is wrong. The light won't turn off during sunlight. It's just on all the time. Anyone know why? It's really bugging me.
@herisantoso9040 Жыл бұрын
Bang apa gk perlu di pasang dioda dari panel surya nya ke modul
@miteshdhanani5 жыл бұрын
On of switch is to be connected then
@raghubhaibharvad67155 жыл бұрын
Bhai .. 12v solarpanel & 12v battrey me use karsata hu ...
@SanjayKumar-bb3sy2 жыл бұрын
1. बैट्री को parellel जोड़ना है या सिरीज़ में 2. बैट्री कितने वोल्ट और कितने mah की होनी चाहिए l 3. Solar पैनल कितनी वोल्ट और कितनी वॉट के होने चाहिए l
@dj_sorra8605 Жыл бұрын
C 1815 IS GOOD FOR THIS PROJECT?
@affalahpramudiasesutio71314 жыл бұрын
How To Make This Than Brighter
@mickcarson85044 жыл бұрын
Good video but the music is a freaking nightmare. Show the video without the Disco.
@andypratamasamudera32512 жыл бұрын
I can use the transistor TIP31C ?
@tossancuyota78488 ай бұрын
huh.....all goods but i think u need to add a resistor to that chonk led or else itll burn out itself
@jcadventurehd6 жыл бұрын
nice video i might try this out
@amigoselvador27865 жыл бұрын
the scheme showing in the video is belong to Edmund Brisenio
@albertnario4877
5 жыл бұрын
yes your right, I have permission from him.
@dj_sorra8605 Жыл бұрын
BC547 or BC557 IS GOOD?
@pieqienenergy5 жыл бұрын
cant work, if I placed the solar board under the sun on the light and if I closed the solar board the lights went off
@solderist
4 жыл бұрын
Must be the transistor
@user-su1go1if5z Жыл бұрын
هل يوجد بديل للترانزيستور ومهو نوعه nbn .؟
@prasoonprashant85872 жыл бұрын
what if i have a 9 volt 3 watt solar panel??
@SanjayKumar-bb3sy2 жыл бұрын
बैट्री को parellel जोड़ना है या सिरीज़ में
@bishalbarua76862 жыл бұрын
how long it can provide lightning?
@mati211p4 жыл бұрын
How did you set current? I can't see any limitations? How much power did you get without resistor? Does it still work well without any resistors?
@generalawareness101
3 жыл бұрын
There is a lot wrong with this circuit, and you spotted one of the issues. The other issue is that there were no diodes used to prevent backflow energy. Normally 1 or 2 Schottky diodes are used to prevent that in 1 or two places in the circuit. The thing is you don't actually have to have a way to set the current in this setup since the 18650's are 3.7v nominal (but can go up to 4.2v) while the 1w led wants about 3.5v. Personally, for longevity of the LED, I would use an XL4056E right before the LED and set the current there so no matter what voltage hits it the current is what is driving it (which is what we want).
2 жыл бұрын
@@generalawareness101, i also thought about the LEDs getting a too high voltage. Even a 3.3V linear regulator possibly would do a good job here while still being more efficient. I don‘t know if the TP4056 already acts as a reverse current protection.
@generalawareness101
2 жыл бұрын
@ It does not and why a diode has to be inserted.
@tupai624 жыл бұрын
what the both solar panel output voltage?
@watchfullbird6381
4 жыл бұрын
6V this is shown at 18secconds in.
@wenzuken222 жыл бұрын
can u teach me the wiring for the transistor its not clear
@abhishorts94775 жыл бұрын
Cool thing can you tell from where to buy these things
@djamad88062 жыл бұрын
bro, why is the 10k resistor not used?
@alittlebitanimation87713 жыл бұрын
where did u connect the transistor
@darman22402 жыл бұрын
Tahan berapa lama tu lampu gan 2 batre... panel suryanya kalu 1 bisa kah.. tks.
@user-uc4kp7rt2e3 жыл бұрын
Que tipo de modulo usaste?
@ALEFILES
Жыл бұрын
TP4056 con protección contra sobrecargas...Saludos desde Argentina!
@anoopanand76194 жыл бұрын
Is possible to connect 6 volt DC LED?
@marcomartins9845 Жыл бұрын
Hi, what type of resistor for a 3w LED? Thanks
@Mister.Doodler Жыл бұрын
Where to buy these
@aml-ph47662 жыл бұрын
where is the 10k resistor?
@ekas90814 жыл бұрын
If a larger LED will be installed, around 5 watts, do the transistors need to be replaced? If replaced, what type of transistor is appropriate?
2 жыл бұрын
These transistors commonly are rated for 300-600mA. A 5W LED could draw 1.5A at 3V. So just look for one that has such current capabilities and is PNP. Also, don‘t connect the LED straight up to the TP4056s output and use a buck regulator instead.
@tabaccopuro5 жыл бұрын
10k resistor missing in your video.
@TheAnical
4 жыл бұрын
I was thinking his large copper wires were resistors somehow?
@zocdelrosario27953 жыл бұрын
failed po ito sa akin ayaw mag off yung led pag may panel na
@hdjdjdjdsjsksisjcjj4 жыл бұрын
it didn't work transistor got super hot and it burn up light never turn off when ligh hit the solar panel
@javijee_
4 жыл бұрын
You must have made the wrong connections.
@jonathanmcalees9223
4 жыл бұрын
I've just made this and I has the same trouble. Sun light doesn't turn mine off. Followed your wiring diagram to the letter.
@schubi1286 жыл бұрын
I tried with 3 such small solar panels in parallel but the TP4056 ciruit never got any reasonable charge even in a single 18650 cell. When I plugged in a USB Charger into the TP4056 board it charge but even with this stable Current supply it took more then 2 hours from 4.1 Volt to 4.2 Volt. I think the TP4056 boards are unable to manage the erratic power supply from the solar cells.
@albertnario4877
6 жыл бұрын
I used it five months before the fruit was struck from the tree, and damaged and i never encountered an issue like yours.
@judeareola6026
6 жыл бұрын
Use a 6v 3.5w solar panel.
@paranormaledits952611 ай бұрын
but does it actually work? Can anyone confirm?
@sarveshpednekar74602 жыл бұрын
Total cost of making?
@rachealleong3712 жыл бұрын
what about the resistor?
@azmilulum32804 жыл бұрын
Sorry, where is the Resistor located
@ضياء63 жыл бұрын
can i use the 2n2222 transistor?
@davidzammit93594 жыл бұрын
For how long it stays on during the night?
@FargothPL
3 жыл бұрын
Until the battery dies. If you use a big enough battery and solar panel, then it will shine all night.
@muhamadhusen8932 Жыл бұрын
where's the resistor bro?
@ekoharyanto20462 жыл бұрын
Resistornya utk apa / dikemanain.??
@adikalijaga55783 жыл бұрын
Alhamdulillah dpt ilmu baru, padamkan api merah , mampir kak
@markskise6 жыл бұрын
where connect a 10k ohms resistor?
@JodBronson
5 жыл бұрын
10k resistor is connected to transistor's base.
@JodBronson
5 жыл бұрын
Transistor Base = Pin #2
@hellofotoo5 жыл бұрын
1015? 1019? and where is the resistor?
@the_moto_monk_ey3 жыл бұрын
since battery is in parallel then it becomes 4000mah.. how much time the led keeps on at night ?
@electrojessy4270
3 жыл бұрын
4ahx 3.7 = 14.8w so around 15 h when full
@astronic45222 жыл бұрын
Nice project
@Nappakoutdoorcamp3 жыл бұрын
pakai cairan apa itu broo? boleh inta link pembeliannya?..
@afzalmusani59434 жыл бұрын
Project success because battery 4.5v connect but not a backup this problem ok pls solw now.
@mayurpawar5623 жыл бұрын
A1015 ka transistor ki but link dedo Nahi mil raha hai
@ucokcupu15 жыл бұрын
How is led 30watt?
@Darkryoka6 жыл бұрын
i buy transistor A1015 online and try to do the same thing but din't work.. it's that a specific A1015 need to use? hope i get the best answers.. tq..
@abbasalimohammedrashed5915
6 жыл бұрын
transistor pn is wrong in diagram
@Darkryoka
6 жыл бұрын
+Abbas Ali Mohammed Rashed tq.. i did it.. ✌✌
@16emmi6 жыл бұрын
Got it 😍thank u
@satryapratama32244 жыл бұрын
Tanya resistor ya di taruh mana bos
@mydrive15323 жыл бұрын
Transitor A9013 ?
@SS3Badminton5 жыл бұрын
How do I use the battery in the morning and the battery charge in the battery and in the evening, do I use the battery?
@DigitalIP
4 жыл бұрын
The solar panels charge the batteries during the day, at night the light uses the batteries. If using a usb cable to charge the batteries the solar panels are pretty much just used to turn the light off during the day.
@dr.jogindersaini7384 Жыл бұрын
Very nice
@tonygriffiths786410 ай бұрын
major overkill on the solar connections, use what you got i suppose
Пікірлер: 267
This panel can put out close to 100 watts kzread.infoUgkxOqI2yqX0XVrhR2BMJciTWrHJpG8FhJyg when positioned in the appropriate southernly direction, tilted to the optimal angle for your latitude/date, and connected to a higher capacity device than a 500. The built in kickstand angle is a fixed at 50 degrees. Up to 20% more power can be output by selecting the actual date and latitude optimal angle.The 500 will only input 3.5A maximum at 18 volts for 63 watts. Some of the excess power from the panel can be fed into a USB battery bank, charged directly from the panel while also charging a 500. This will allow you to harvest as much as 63 + 15 = 78 watts.If this panel is used to charge a larger device, such as the power station, then its full output potential can be realized.
This is correct pin for A1015 : OUT+ (emiter/pin1), LED+ (collector/pin2/middle), IN+ (base/pin3)
@zulkarnainzamin1183
3 жыл бұрын
meaning?
Collector max Current: -0.15 A for A1015 transistor and current of 1W LED is: 1W/3,3V= 0.3A. We have to add resistor(may be 10-12 Ohm) between collector and anode pins. It"ll be save LED"s life (and battery, too).
@ronaldd.1355
4 жыл бұрын
Why do you need a resistor? in my calculations it is not needed. The batteries when full charged 'll be: 4.20, the LED is about 3.3v, so you have to reduce: 0.9v, so (0.9v / 300ma) = 3OHMS. Not 10000, Am I right?
@arazmamedzade8110
4 жыл бұрын
@@ronaldd.1355 Dear Ronald, there is such a thing as "instantaneous current value", which affects the moment the load is turned on. This current exceeds the rated current by 5-6 times. In order for the LED (load) to not burn during switching on, we take a resistor 3-4 times more. In all other respects - of course you are right.
GREAT VIDEO! can you show us how to change a pre-made outdoor solar security light? maybe how to make them turn on & off when we WANT instead of being motion detected? and maybe add a ?? dial if possible? to turn them up brighter or down for lower lighting? Then finally my biggest question! Is there any way to use these solar power lights for an alternative purpose? by maybe taking OUT the light, probably double up the batteries? and add a USB charger? I have 8 brand new ones, and I've already separated 3. Placed the solar on my outside & the light on my inside for motion detected lighting inside, but really they're brighter than I need. They stay going 3 days now so far with overcast! Free lighting! Yay!! (free solar phone charging would be AWSOME!
I tried this and the led is not turning off when there is current from solar panel. I used A1015 GR331 transistor, whats the problem?
Я не парю мозг а сразу собираю подобную схему в уличный светильник вместо лампы на 220 в. Просто красиво экономично. И схема у меня сложнее с четким переключением на стабилизаторе tl431 и естественно с дополнительной бмс для 18650. А тут уж больно дешманский вариант из бокса для обеда😎
@sergeyboitsov8643
Жыл бұрын
А чём разница между тем что в видео и tl431? правильно ли я понимаю, что tl431 как раз будет включать нагрузку когда темнеет?
Your 2x 1watt 6 volts solar panel are verry weak to charge 2x 2000mAh lithium battery. Cuz your 2 panel can only produce 0.333 amps of current, not much. (P/E or V=I) you do the math. And the TP 4056 will ignore it. Cuz TP4056 have a minimum accepting current of 37% battery capacity. So if you have 2x 2000mAh battery, you need 0.740amps of current from the panel to charge your battery. It means u need 5watts 6volts solar panel that can produce 0.833 amps of current enough to charge those 2x 2000mAh battery. But overall, i love the video. You work clean.
Nice tip with the nail varnish, not seen that technique since my high school years 91-96
Excellent DIY Video. Very practical sourcing of readily available materials. Smart design. THANKS BRO!
@adrienrandall9483
3 жыл бұрын
You all prolly dont give a damn but does someone know a tool to log back into an instagram account?? I was stupid lost the password. I would love any help you can give me
@bowenowen5818
3 жыл бұрын
@Adrien Randall instablaster ;)
@adrienrandall9483
3 жыл бұрын
@Bowen Owen thanks so much for your reply. I got to the site thru google and im trying it out atm. I see it takes quite some time so I will get back to you later with my results.
@adrienrandall9483
3 жыл бұрын
@Bowen Owen it worked and I finally got access to my account again. Im so happy! Thanks so much, you saved my account :D
@bowenowen5818
3 жыл бұрын
@Adrien Randall No problem =)
Cool. Same as my circuits. Good Job
@cinderelladreamshop1310
3 жыл бұрын
is it working same as video? With tp4056 charger module also? Need any diode?
Mantap mas bro Creative bikin lampu solar cell nya
What is functioning of resistor...
What's the resistor for?
@samwallin9694
2 жыл бұрын
it was not used when i made this i used a 20 ohm resistor inline with the negative side of the led and that drops down the voltage as i was worried about burn out
This is a pnp transistor. Shouldn't the base be connected to the negative of the solar panel? Wouldn't connecting the base to the opposite polarity be causing a short? It should honestly still work since electrons move from the negative to the positive terminal so it'll eventually reach the base but still i can't help but think it is causing a short somewhere.
@ALEFILES
8 ай бұрын
Not at all. The base is connected to the right pin (+), because when the sun lights the panel, the +V of the panel _BLOCKS_ the PNP transistor, and _when the night comes,_ the voltage of the panel fall to zero, activating the transistor, and driving current from battery to the Led across the collector... Understood? Greetings from Argentina!❤
Hola...cual transistor debo usar?...a1015 o a1019...gracias
Does the value of the resistor depend on the current drawn by the connected load? Does the life of the battery depend on the resistance? What is the maximum current drawn by the load in this circuit?
@ALEFILES
8 ай бұрын
The maximum current _DEPENDS_ of the maximum current the transistor can drive...If you use a small transistor, don't expect to connect a BIG led light, because you will burn the transistor...I suggest to use a BD140, TIP42C or similar, BUT REMEMBER: anything transistor you use MUST be PNP, otherwise the light won't turn on by night... It will be better If you use a MOSFET P-CHANNEL instead a bipolar transistor (e.g. IRF9640)... Greetings from Argentina!❤
Nice but you did not show the 10k resistor on schematic or where to solder. I assume this is the base current controlling resistor?
@xlines
6 жыл бұрын
EnergyCrafts the 10k resistor is more likely for the base of the transistor.
@judeareola6026
6 жыл бұрын
kzread.info/dron/EfGr5XZvclJliyoFwT9n_g.html Check this one out.
@nikhilganguly546
5 жыл бұрын
10 k resistor should be added in the transistor b
you can look for cable box 10cm×10cm cost about 1 $ per box that kind of box used indoor or outside the house kind of waterproof
Out battery - 4,2v. LED in 3,3-3,4v. Need resistor for stabilisation carrent LED...?
@FargothPL
3 жыл бұрын
There's no need. You're losing some voltage across the transistor. I recreated a similar project (I found where I made a mistake when I previously use his scheme) and the voltage on the diode was 3.17V (so for white LED is ok), while the battery voltage was 4.1V
@phitrow
3 жыл бұрын
@@FargothPL ok
Is the transistor working as some sort of current regulation there, or is the LED straight up getting the full battery voltage? If the second thing is the case, use a 3.3v regulator (if it‘s a linear one, it can still waste up to 800mW with a 3W LED but the LED will get a constant current).
@samwallin9694
2 жыл бұрын
its working as a switch it turns off the leds while the solar pannel is providing voltage which charges the batterys, but when the pannels are not producing voltage the leds turn on and use the battery voltage
2 жыл бұрын
@@samwallin9694 I know, it‘s a PNP type transistor. I just don‘t know if it has a internal resistance, because it‘s the only thing between the LED (2.6 to 3.3V) to the battery (2.6 to 4.2V).
@ALEFILES
Жыл бұрын
@@samwallin9694 How does the current flow from batteries to the 1W Led (+) lead at night? The PNP transistor turns ON when it is night? If it is, the 2SA1019 transistor doesn't drive much current, just 0.05A, and the 1W LED needs at least 0.300 A... Greetings from Argentina!
@sshutupurface8345
Жыл бұрын
i use 1k resistor with 18650 so the current is 4.2 milliamps and the led emits 0.017 watts good as night light lasts 55 days + permanently on
But where you have used that 10k resistor
Clear Coating would also help with protection, instead of using nail polish etc.
Mine working reverse, as the panel charges the led glows. Whats wrong i did?
@rimbang_
6 жыл бұрын
Dhiren Swain yah me to
@amigoselvador2786
5 жыл бұрын
Dhiern swain same here
@omnidive3416
5 жыл бұрын
make sure to use a PNP transistor, NPN transistors turn things on when current is applied and PNP transistors turn things off when current is applied. This means that with a PNP transistor, the solar panel will give current to the transistor base, turning off the LED. When the panel is not producing power (night), there is no current and the LED turns on.
Albert. I prefer you talking on your videos. Its way better than music. Para ma explain mo nang mabuti.
Goodday. What a simpel and great solution for this application. Is there a way to make the LED go on when it is a bit more dark? Mine is going on very soon...
Can I use any other npn transistor
great video , can you do video about 6/10w led light circuit
The box is not resistant to sun. Box life is 1 or 2 year. Nice job.
@albertnario4877
3 жыл бұрын
it's enough time for it.
Hi, question: solar panel input is 1w/6v =. 17A. Two panels =. 34A. Is that enough to charge the battery for whole day? Or is the TP4056 can boost amp? Sorry for the question if it's stupid or easy. Thanks
@ALEFILES
Жыл бұрын
The TP4056 only DRIVE the current from the panel to charging batteries, don't boost voltage or amp...Greetings from Argentina!
Where is the resistor??? 🤣🤣🤣
@markangelosegurola
2 жыл бұрын
Bro read the description
@bangladesh2365
2 жыл бұрын
10k........😂😂😂😂😂
@miteshdhanani
Жыл бұрын
@@markangelosegurola show the description
@satriyobaru9451
Жыл бұрын
what is the resistor for?😂😅😅
@desainalf
9 ай бұрын
@@satriyobaru9451for seLLing.. 😂
Emitter should be connected to ground and collector connected to negative of the led .
@amigoselvador2786
5 жыл бұрын
could you please explain more in a simpler way thank you
Will it work with singel 5vpanel and single 18650 lithium battery?
@yavuzcan233
3 жыл бұрын
it works
Can you double check your circuit diagram ? I made it like you showed in circuit diagram but it is not working.
@samwallin9694
2 жыл бұрын
the diagram is incorrect use kzread.info/dash/bejne/Y32C0MqOYa3Tlto.html for the correct orientation
I followed the video to a T, but still something is wrong. The light won't turn off during sunlight. It's just on all the time. Anyone know why? It's really bugging me.
Bang apa gk perlu di pasang dioda dari panel surya nya ke modul
On of switch is to be connected then
Bhai .. 12v solarpanel & 12v battrey me use karsata hu ...
1. बैट्री को parellel जोड़ना है या सिरीज़ में 2. बैट्री कितने वोल्ट और कितने mah की होनी चाहिए l 3. Solar पैनल कितनी वोल्ट और कितनी वॉट के होने चाहिए l
C 1815 IS GOOD FOR THIS PROJECT?
How To Make This Than Brighter
Good video but the music is a freaking nightmare. Show the video without the Disco.
I can use the transistor TIP31C ?
huh.....all goods but i think u need to add a resistor to that chonk led or else itll burn out itself
nice video i might try this out
the scheme showing in the video is belong to Edmund Brisenio
@albertnario4877
5 жыл бұрын
yes your right, I have permission from him.
BC547 or BC557 IS GOOD?
cant work, if I placed the solar board under the sun on the light and if I closed the solar board the lights went off
@solderist
4 жыл бұрын
Must be the transistor
هل يوجد بديل للترانزيستور ومهو نوعه nbn .؟
what if i have a 9 volt 3 watt solar panel??
बैट्री को parellel जोड़ना है या सिरीज़ में
how long it can provide lightning?
How did you set current? I can't see any limitations? How much power did you get without resistor? Does it still work well without any resistors?
@generalawareness101
3 жыл бұрын
There is a lot wrong with this circuit, and you spotted one of the issues. The other issue is that there were no diodes used to prevent backflow energy. Normally 1 or 2 Schottky diodes are used to prevent that in 1 or two places in the circuit. The thing is you don't actually have to have a way to set the current in this setup since the 18650's are 3.7v nominal (but can go up to 4.2v) while the 1w led wants about 3.5v. Personally, for longevity of the LED, I would use an XL4056E right before the LED and set the current there so no matter what voltage hits it the current is what is driving it (which is what we want).
2 жыл бұрын
@@generalawareness101, i also thought about the LEDs getting a too high voltage. Even a 3.3V linear regulator possibly would do a good job here while still being more efficient. I don‘t know if the TP4056 already acts as a reverse current protection.
@generalawareness101
2 жыл бұрын
@ It does not and why a diode has to be inserted.
what the both solar panel output voltage?
@watchfullbird6381
4 жыл бұрын
6V this is shown at 18secconds in.
can u teach me the wiring for the transistor its not clear
Cool thing can you tell from where to buy these things
bro, why is the 10k resistor not used?
where did u connect the transistor
Tahan berapa lama tu lampu gan 2 batre... panel suryanya kalu 1 bisa kah.. tks.
Que tipo de modulo usaste?
@ALEFILES
Жыл бұрын
TP4056 con protección contra sobrecargas...Saludos desde Argentina!
Is possible to connect 6 volt DC LED?
Hi, what type of resistor for a 3w LED? Thanks
Where to buy these
where is the 10k resistor?
If a larger LED will be installed, around 5 watts, do the transistors need to be replaced? If replaced, what type of transistor is appropriate?
2 жыл бұрын
These transistors commonly are rated for 300-600mA. A 5W LED could draw 1.5A at 3V. So just look for one that has such current capabilities and is PNP. Also, don‘t connect the LED straight up to the TP4056s output and use a buck regulator instead.
10k resistor missing in your video.
@TheAnical
4 жыл бұрын
I was thinking his large copper wires were resistors somehow?
failed po ito sa akin ayaw mag off yung led pag may panel na
it didn't work transistor got super hot and it burn up light never turn off when ligh hit the solar panel
@javijee_
4 жыл бұрын
You must have made the wrong connections.
@jonathanmcalees9223
4 жыл бұрын
I've just made this and I has the same trouble. Sun light doesn't turn mine off. Followed your wiring diagram to the letter.
I tried with 3 such small solar panels in parallel but the TP4056 ciruit never got any reasonable charge even in a single 18650 cell. When I plugged in a USB Charger into the TP4056 board it charge but even with this stable Current supply it took more then 2 hours from 4.1 Volt to 4.2 Volt. I think the TP4056 boards are unable to manage the erratic power supply from the solar cells.
@albertnario4877
6 жыл бұрын
I used it five months before the fruit was struck from the tree, and damaged and i never encountered an issue like yours.
@judeareola6026
6 жыл бұрын
Use a 6v 3.5w solar panel.
but does it actually work? Can anyone confirm?
Total cost of making?
what about the resistor?
Sorry, where is the Resistor located
can i use the 2n2222 transistor?
For how long it stays on during the night?
@FargothPL
3 жыл бұрын
Until the battery dies. If you use a big enough battery and solar panel, then it will shine all night.
where's the resistor bro?
Resistornya utk apa / dikemanain.??
Alhamdulillah dpt ilmu baru, padamkan api merah , mampir kak
where connect a 10k ohms resistor?
@JodBronson
5 жыл бұрын
10k resistor is connected to transistor's base.
@JodBronson
5 жыл бұрын
Transistor Base = Pin #2
1015? 1019? and where is the resistor?
since battery is in parallel then it becomes 4000mah.. how much time the led keeps on at night ?
@electrojessy4270
3 жыл бұрын
4ahx 3.7 = 14.8w so around 15 h when full
Nice project
pakai cairan apa itu broo? boleh inta link pembeliannya?..
Project success because battery 4.5v connect but not a backup this problem ok pls solw now.
A1015 ka transistor ki but link dedo Nahi mil raha hai
How is led 30watt?
i buy transistor A1015 online and try to do the same thing but din't work.. it's that a specific A1015 need to use? hope i get the best answers.. tq..
@abbasalimohammedrashed5915
6 жыл бұрын
transistor pn is wrong in diagram
@Darkryoka
6 жыл бұрын
+Abbas Ali Mohammed Rashed tq.. i did it.. ✌✌
Got it 😍thank u
Tanya resistor ya di taruh mana bos
Transitor A9013 ?
How do I use the battery in the morning and the battery charge in the battery and in the evening, do I use the battery?
@DigitalIP
4 жыл бұрын
The solar panels charge the batteries during the day, at night the light uses the batteries. If using a usb cable to charge the batteries the solar panels are pretty much just used to turn the light off during the day.
Very nice
major overkill on the solar connections, use what you got i suppose
Hi can you post the diagram of the pcb please
link please where to buy
Dada solar panel ka kitna rupee
Excellent 👌
Awesome 😀👍👍👍👍
R 10k ต่อเข้าตรงไหน
esoknya hilang di curi orang...😀😂🤣
Achhaa he ♂️