This video is a part of our dishwasher series in our members section
Жүктеу.....
Пікірлер: 25
@mikepeters6953Ай бұрын
I've been fixing my own appliances for > 50 years with tons of trial-and-error. I wish I had this info. Excellent work and great teaching! Thank you.
@fixitfelix718 Жыл бұрын
Rich never disappoints hes a real "technician " some people are "repair men" ..nothing wrong with being a regular repairman but everyone should try to get to the level of being able to teach the thing they do and get to expert level
@Ashroyer86
Жыл бұрын
Close, but hes the technician's teacher.
@BC-ms3zsАй бұрын
Love this!!
@douglasduda6890 Жыл бұрын
Excellent teacher, excellent class. First rate. Thank you.
@TMMApplianceRepair
Жыл бұрын
Thank You
@YOGiiZA Жыл бұрын
Excellent , Thank yo for publishing this
@sandrasegrest35965 ай бұрын
You are best source of information ….
@pipi77312 ай бұрын
Well I have a GE Adora Dishwasher that want drain. So now I got a good idea about what the problem may be. I have already changed the float switch as it was bad and the drain pump. Everything else works. So, that would eliminate the door switches I think. Got to be the board I think. Any suggestions?
@natepeterson7145 Жыл бұрын
@TMM Appliance Network can you please raise the volume there's a LOT of your videos I can't watch unless I'm in a library. Please address this and this channel will be as big as it should be.
@seanstrickley3992
Жыл бұрын
That is exactly why I bought a fm transmitter for the work truck so I can hear it while driving but it's still a little hard cause it's not the clearest it could be
@riz65
Жыл бұрын
I ordered lapel mics, will see if it's any better
@natepeterson7145
Жыл бұрын
@@riz65 it should be better because when you're closer to the camera it's much better. Thanks Rick
@emilioescobedo30248 ай бұрын
Where does 12vdc come in,or is everything 12vdc,shows 120v going into the dishwasher
@fixitfelix718 Жыл бұрын
Wouldn't a temp sensor or thermistor be a control for example a bimetal just a bimetal switch that controls a function? As opposed to a load like the heater it controls
@TMMApplianceRepair
Жыл бұрын
Well a thermistor is a resistor that changes its value based on temperature. Yes the board uses this resistance and calculates the temperature. The reason I call it a load as it does not directly turn anything off like a switch does, the control board does that. it is a fine line between the two and could be called a control but indirectly.
@fixitfelix718
Жыл бұрын
@@TMMApplianceRepair ah understood..what about a defrost bi metal that will open and cut off the heater in a freezer? The resistor makes sense to me now thanks
@fixitfelix718
Жыл бұрын
I assume bimetal is a control and thermistor going through board is.more of a load.
@riz65
Жыл бұрын
@@fixitfelix718 yes, the board does usually supply 5vdc through the thermistor, very similar to a load
@fixitfelix718
Жыл бұрын
@@riz65 thanks makes sense
@PrincernPrince11 ай бұрын
Excellent Teaching!! But LOL some of these guys are going to be technicians? Don't get me wrong, I have never had any experience in this, but after sitting through the whole session all of the sub diagrams addressing the door switches, dispenser and drain motor and then teach draws a diagram circuit through the heater and thermostat and asks "What one thing you should test first?" and dude said Rinse Level Sensor with no lines anywhere near it 🤣Please don't send him to my house.
@broncheemims8493 Жыл бұрын
Where can I go to get all the service manuals to down load on my ipad?
@riz65
Жыл бұрын
Appliantology costs for yearly subscription but they have lots of diagram and manuals, otherwise uou jave to be factory authorized servicer
@sbryan409 ай бұрын
where is a good website to go and get diagnostic mode for appliances or schematics?
Пікірлер: 25
I've been fixing my own appliances for > 50 years with tons of trial-and-error. I wish I had this info. Excellent work and great teaching! Thank you.
Rich never disappoints hes a real "technician " some people are "repair men" ..nothing wrong with being a regular repairman but everyone should try to get to the level of being able to teach the thing they do and get to expert level
@Ashroyer86
Жыл бұрын
Close, but hes the technician's teacher.
Love this!!
Excellent teacher, excellent class. First rate. Thank you.
@TMMApplianceRepair
Жыл бұрын
Thank You
Excellent , Thank yo for publishing this
You are best source of information ….
Well I have a GE Adora Dishwasher that want drain. So now I got a good idea about what the problem may be. I have already changed the float switch as it was bad and the drain pump. Everything else works. So, that would eliminate the door switches I think. Got to be the board I think. Any suggestions?
@TMM Appliance Network can you please raise the volume there's a LOT of your videos I can't watch unless I'm in a library. Please address this and this channel will be as big as it should be.
@seanstrickley3992
Жыл бұрын
That is exactly why I bought a fm transmitter for the work truck so I can hear it while driving but it's still a little hard cause it's not the clearest it could be
@riz65
Жыл бұрын
I ordered lapel mics, will see if it's any better
@natepeterson7145
Жыл бұрын
@@riz65 it should be better because when you're closer to the camera it's much better. Thanks Rick
Where does 12vdc come in,or is everything 12vdc,shows 120v going into the dishwasher
Wouldn't a temp sensor or thermistor be a control for example a bimetal just a bimetal switch that controls a function? As opposed to a load like the heater it controls
@TMMApplianceRepair
Жыл бұрын
Well a thermistor is a resistor that changes its value based on temperature. Yes the board uses this resistance and calculates the temperature. The reason I call it a load as it does not directly turn anything off like a switch does, the control board does that. it is a fine line between the two and could be called a control but indirectly.
@fixitfelix718
Жыл бұрын
@@TMMApplianceRepair ah understood..what about a defrost bi metal that will open and cut off the heater in a freezer? The resistor makes sense to me now thanks
@fixitfelix718
Жыл бұрын
I assume bimetal is a control and thermistor going through board is.more of a load.
@riz65
Жыл бұрын
@@fixitfelix718 yes, the board does usually supply 5vdc through the thermistor, very similar to a load
@fixitfelix718
Жыл бұрын
@@riz65 thanks makes sense
Excellent Teaching!! But LOL some of these guys are going to be technicians? Don't get me wrong, I have never had any experience in this, but after sitting through the whole session all of the sub diagrams addressing the door switches, dispenser and drain motor and then teach draws a diagram circuit through the heater and thermostat and asks "What one thing you should test first?" and dude said Rinse Level Sensor with no lines anywhere near it 🤣Please don't send him to my house.
Where can I go to get all the service manuals to down load on my ipad?
@riz65
Жыл бұрын
Appliantology costs for yearly subscription but they have lots of diagram and manuals, otherwise uou jave to be factory authorized servicer
where is a good website to go and get diagnostic mode for appliances or schematics?
@pipi7731
5 ай бұрын
Great question.