it must great going under your trucks in AUS, so clean and very little to no rust, here in uk its a nightmare looking under the truck, keep up the good work.

@OUTBACKDiscovery

2 жыл бұрын

Definetly nice being able to get bolts undone 🤣 have seen some horrendous rusty vehicles on the discovery 3 and 4 pages and always European 🤣🍻

That was relaxing for me in front of the TV. Normally I am in that position. Winter clothes? I saw none. Christian

@OUTBACKDiscovery

2 жыл бұрын

That's how I feel when I watch your videos 🤣 always making up tools on your lave and getting me jealous haha

Man. We out here struggling with this disco life😂. Mine is coming together now. And here is a fact for all of you . Changing the turbo is actually a bitch even with the body of. Give this man the respect he deserves.

@OUTBACKDiscovery

2 жыл бұрын

Haha thanks kami how far away are you now mate ?

😅👍My winter clothes look definitely different. I'll bet your camshaft seal is leaking because you didn't push it in the LR Time style. We'll we had a leak too on that camshaft seal because we didn't push it in correctly. Hope everything worked out for you. I am finally going to appreciate that Christian is putting a high lift into our driveway. So if my Turbo goes one day, it will be a body-off repair. 💪😃🙋‍♀Vera

@Vera_and_Christian

2 жыл бұрын

Well, we screwed up a camshaft seal as well and we did use our high end LR Time push in tool. Problem was the tool slipped into the chamfer. Arg. Had to open it again on Veras car. Christian

@OUTBACKDiscovery

2 жыл бұрын

@@Vera_and_Christian 🤣 what's wrong with the that's about 1mm approach 😅🤣 could be a high possibility I'll be wearing a t shirt and socks with my crocks whilst kerry is wearing her heated jacket and socks Still not to cold here I think it hit 0 degrees the other day 🤣

@OUTBACKDiscovery

2 жыл бұрын

Also trying to budget in a hoist when I extend the shed still a few years away though

Thanks grate wideo 👍👍👍

Good job.

Thanks for the tip on making the tool i was so temted to just pull the moter today i cant thank u enougth But on the one im working on they weld an nut on one of the pipes also giving me an headace

@OUTBACKDiscovery

2 ай бұрын

Man it's such a pain in the butt haha honestly such a hard engine to work on, have you got it out yet

Always doing some major work man! Those TDV6s need the extra love huh! Over here in the states, I got the gas V6 4.0, pretty solid engine, all I’ve ever done is an EGR, damn gas hog though!

@OUTBACKDiscovery

2 жыл бұрын

🤣 it's never ending woukd live to get the v8 petrol over here but super rare to find one Only other thing with the v6 4ltr its timing chain guides from memory but as you said a solid engine

Good time to change your AC pump as well!! Hope that's not next. Same age as ShaneShed's. Your car is super clean underneath!!!!!

Well if I ever need to change my turbo I know who to see to borrow the specially tools...

Great job looking forward to part 2 👍 socks with crocks 😱let's hope Christian doesn't get his Lederhosen on 😱😱😱OMG

@OUTBACKDiscovery

2 жыл бұрын

Hahaha 🍻🤣

Hi great video sometimes the rod on the actuator becomes lose and jams on one of the nut heads what I do is take the heat shielding of in the wheel arch . I have 2 hack saw blades glued together you only 4 inches of it the2 make it stiffer and shave 2 mill of the top nut head the arm can’t jam then I’ve done 8 of them now a lot easier than doing a turbo

@OUTBACKDiscovery

2 жыл бұрын

Hey William great advice I'd went through all these checks before hand spent alot of time going through everything before committing to the job 🤣 actuator was nice and free with very little play I misaligned the actuator when replacing the turbo cartridge during my engine rebuild unfortunately

Well I might end up having to do a turbo replacement on my D3. Actuator is sticking and playing up resulting in bugger all boost

Extra 10 minutes for the cross member. Mine took about 6 hours.

@OUTBACKDiscovery

Ай бұрын

🤣 I'm guessing your in the UK or Europe somewhere ?🤣 Dropped that cross member on a fair few over here in Australia and because rust isn't to much of an issue here there always friendly to me when doing so haha

I respect the work u are doing, will u tap thread in the top 2 exhaust stud holes and put bolts with anti seize on then in?

@OUTBACKDiscovery

2 жыл бұрын

The new turbo actually had no thread in the turbo so I just passed a bolt through with a mechanical lock nut of the other side * metal style rather then rubber *

Brilliant mate, thats one hell of a job, would you mind doing a quick view on the actuator on the bench, mine i think is goosed i would appreciate that or in Insta, excellent as always mate

@OUTBACKDiscovery

2 жыл бұрын

Hey John not currently home sorry but if you skip through to the disassembly of the turbo on this video it will give you a good view it's from when I replaced the cartridge on the one I remove in this video kzread.info/dash/bejne/aIKFwaVsYcjVdpM.html

Hello Mate, i was having a Engine System Fault message on my dashboard so i decided to remove the Turbo on my 2005 Range Rover Sport 2.7TDV6 and cleaned the internal Turbo Vanes to ensure free movement of the Turbo Actuator Arm. Before removal of the Turbo i was getting error code P132B-00 - Turbo/Supercharger boost control A performance (permanent), now after cleaning up the Turbo, i also decided to reAdjust the adjustment screw settings for the actuator arm to have more room for movement. After re installing the Turbo back in the car the Engine System Fault error was gone and there were no more error lights on my dashboard. I am now getting DTC P138E Turbocharger boost control position sensor A - minimum/maximum stop performance with no error lights on my dashboard. I am also experiencing power loss on high rpm with these DTC's "B1B02-28 Low Frequency Coil" and "B1C57-14 Unused relay drive". Could you please help me solve the problem with my car. It is a 2005 Range Rover Sport 2.7TDV6. Thanks

@OUTBACKDiscovery

Жыл бұрын

Morning brakelyn Cleaning the vanes would of helped the actuator move freely and helped get rid of that code Unfortunately these are pretty sensitive to adjust and I misaligned mine I also got the control position a fault after doing mine and occasionally the a couple of other faults I can't remember the name of to go with it Once I replaced the turbo with a new unit they all went away Chances are your turbo actuator is out of adjustment now that you have played with the adjustment screw

Ive got shed envy! How's that floor?! Something is wrong with your Disco. It's missing the air suspension 😢 Hat off to you on this job. I just did the coolant inlet and did a comparatively crappy yt vid on it. Found it pretty difficult tbh.

@OUTBACKDiscovery

Жыл бұрын

🤣 floor doesn't look like thay any more all stained and chipped Unfortunately she's the base model which was factory coil sprung so no choice in the matter Quality of the video doesn't mean much anyway dude just focus on getting the correct information out there and people will appreciate it I no my videos are boring to watch but I no it helps others so I keep doing them haha Good luck with your channel

Just as a side question, at the end did turbo replacement fixed the issue you had with engine error in 6th gear, or was it something else?

@OUTBACKDiscovery

11 ай бұрын

Hello yeah the turbo fixed the problem, the only reason it faulted in 6th gear was because of where it sat in the rev range so the auto had nothing to do with the fault if that what you were thinking I just had to keep the revs high to stop the turbo actuator closing off which ment not using 6th gear at 100kmph Hope this helps

@serpentonline

11 ай бұрын

@@OUTBACKDiscovery i have manual one but with the same issue. On/off and the error is gone, but it comes back when i accelerate in low rpms or when over 3k overtaking. Changed the intercooler hoses and cleaned MAP, EGR is vlanked off, so my assumption is turbo (i checked and actuator seems to move as expected visually)... :(

@OUTBACKDiscovery

11 ай бұрын

@@serpentonline true what fault codes are you getting ? Is it something along the lines of boost actuation C or similar wording

got a SWMS for the angle grinder & multis hehehe

@OUTBACKDiscovery

2 жыл бұрын

🤣 definetly not a mine site approved approach that's for sure 🤣🍻

It is the same on range rover sport 2.7 tdv6?

@OUTBACKDiscovery

Жыл бұрын

Sure is Valentin 🍻

For some reason, it looks like you have more space than I do to undo the turbo bolts….😢

@OUTBACKDiscovery

24 күн бұрын

@alinvlaic191 looks can be deceiving there was very little 🤣 off camera I was swearing alot 12 years in the trade can also make things look a little smoother then normal also pretty used to working in annoying situations like that now Have done 1 more turbo since with the same tool felt pretty similar have you pulled all the head shields off

@alinvlaic191

24 күн бұрын

@@OUTBACKDiscovery I tried building a tool like yours but I did not have enough space and then I built another one with half an inch drive and still not enough space so then I welded a spanner end and then it worked perfectly

@OUTBACKDiscovery

24 күн бұрын

@alinvlaic191 as long as you got it done in the end 💪 Mine was 3/8 drive and half of the 3/8 head had to be cut off for it to fit in the gap if that makes sense

Would you be interested in doing a turbo swap job$$$

@OUTBACKDiscovery

Жыл бұрын

Hey brendo I would be however the time frame would be an issues as I'm currently booked up for the next couple of months What engine is yours the 2.7 or 3ltr