You save my life Today! I needed to replace fuser unit. With this tutorial I did it in 20min. Thank You!

This is the best instruction.

Excellent video. Thanks.

TNKS

Thank you

@viandant5 great video! I have CLP 320 (no wifi)- can I replace motherboard from CLP325W (with wifi module)? It this will work?

@viandant5

3 жыл бұрын

No, I think it will not work

Hello, thank you for your useful videos!! I have a problem with a used Samsung CLP-680 that I bought from eBay because the listing said that it was in excellent condition and had only about 800 printed pages. However the colors are not aligned. I cleaned it inside, I went on the tech menu and printed the Auto Color Registration page and the X-Offset and Y-Offset values are different numbers, and don't change when I run the Auto Color Reg or open and close the tray. The toners are the starter Samsung. Is there a way to manually change the offset values or the problem is caused by a faulty part? Could you help? Thank you

@viandant5

Жыл бұрын

If I remember well there is no method to manually change the alignment values. I think the problem is a faulty part, but it's difficult to say which part. May be even a deformation of the mainframe

@rorygt3

Жыл бұрын

@@viandant5 Thank you for your reply!! I will try a firmware update in case this can correct something, before sending it for service or keeping it as office decoration! Greetings from Greece, una faccia una razza 🙂

My similar printer CLP325 stopped working recently. It just would not power on. It was shut manually from the switch and then it never worked since. Do you think it is power supply? Are they simple to screw in if i buy new power supply or does it require any soldering etc. Thanks in advance

@viandant5

3 жыл бұрын

The power supply has screws. Before to change the power supply in this channel there is a video on how to do if the printer doesn't turn on

Where can I purchase the sensor to correct paper jams as in your video for a Samsung CLP-315?

@viandant5

Жыл бұрын

Try Aliexpress

It is possible for you to help me and teach me the voltage measurement of the main board and the format😊😊

@viandant5

4 ай бұрын

without the electrical scheme it's really difficult make an affordable and usefull meausurement

Hi, Nice video! I have a problem with my clp325w which I cannot solve... When powered on, after 2seconds the status led and the 4 toner leds go all solid red and stay endlessly red and none of the button (cancel/testprint, WPS or even OFF) will work. Also not possible to connect to printer from Lan or USB anymore. Does this sound familiar to you? Do you have any clue how I could bring it back to work? Thank you in advance for your help!

@viandant5

4 жыл бұрын

The manual says it could be a paper jam, a toner cartridge not correctly installed, no paper in the cassette or a broken paper sensor. Try to empty the waste toner box

@sandromigliardi9755

4 жыл бұрын

@@viandant5 Hi Viandant5, thanks for coming back to me. I had actually already tried that, cleaned it with water, let it dry and reinstalled it but it doesn't help. Also removed/reinstalled several times cartridges and imaging unit, checked for paper jam but nothing helps and printer will each time go red light after 2 seconds. The only possible 'action' is to remove the power cord :-( Thinking back, a few weeks ago I replaced empty genuine cartridges with new non genuine cartidges which were immediately recognized and I was able to use my printer normally until 3 days ago. Anyways thanks for caring. I was hoping to be able to hard reset the unit in a 'mechanical' way since I don't have access to the user interface. It seems to me that the unit is in a kind of 'protection mode'

Mine stopped working ,it started heating the fuser ,than went all off All it does now is making a clicking sound ,any help ?? Thanks in advance

@viandant5

2 жыл бұрын

It could hav lot of causes, sorry it's not possible to give an answer without checking the printer. It seems the current from the power supply does not arrive to the machine

Hello, could you help me to solve a failure in a Samsung ML-1710 printer, which for some time now began to print from the middle of the sheet downwards, I tell you that when it started to fail, the first two or three sheets It printed them with the fault and the next sheet already printed well, but now it no longer prints any sheet correctly, I disassembled it and cleaned the sensors with air and it still has the fault, what could you advise me to repair the fault? Where I live there are almost no qualified technicians or they charge very expensive. Thanks in advance. Sincerely: Jose Alberto P.S. I am using the translator, I am from Michoacan, Mexico.

@viandant5

4 ай бұрын

I think it's better if you use spanish language.could it be a setting problem?

@albertoquesada6356

4 ай бұрын

Por supuesto, y te agradezco la atención, te comento enseguida: Hola, podrias ayudarme para solucionar una falla en una impresora Samsung ML-1710, que de un tiempo hacia acá comenzó a imprimir a partir de la mitad de la hoja hacia abajo, te comento que cuando empezó a fallar, las dos ó tres primeras hojas las imprimía con la falla y la siguiente hoja ya la imprimía bien, pero ahora ya no imprime ninguna hoja correctamente, la desarmé y le limpié con aire los sensores y aun sigue con la falla, que me podrias aconsejar para reparar la falla ? donde vivo casi no hay técnicos calificados o cobran muy caro. gracias de antemano.

@albertoquesada6356

4 ай бұрын

Hola, podrias ayudarme para solucionar una falla en una impresora Samsung ML-1710, que de un tiempo hacia acá comenzó a imprimir a partir de la mitad de la hoja hacia abajo, te comento que cuando empezó a fallar, las dos ó tres primeras hojas las imprimía con la falla y la siguiente hoja ya la imprimía bien, pero ahora ya no imprime ninguna hoja correctamente, la desarmé y le limpié con aire los sensores y aun sigue con la falla, que me podrias aconsejar para reparar la falla ? donde vivo casi no hay técnicos calificados o cobran muy caro. gracias de antemano.@@viandant5

@viandant5

4 ай бұрын

@@albertoquesada6356 it could be the toner cartridge but it's difficult to be sure without checking the printer.