Thanks for posting this video. I’ve been researching diesel heaters for a few weeks and I finally decided to buy one. I received and hooked it up and the controller was abnormal. All of the videos I saw in the past were of the old controller. Thanks again for this video!

Like so many others here, your presentation was absolutely helpful. It helped that you illustrated the difference between the earlier controller and the one I now have. Before, I was looking for the signal bars that no longer exist on the newer controller. Your steps worked perfectly, even for my second controller. I really think they keep changing up these controllers to keep us foreigners constantly confused! Good job!

Thank you for saving the day I was looking I kept on finding all of the old controller videos and then I seen your thumbnail made my life easy getting the heater going in my semi just installed it last night thank you very much for the video

Man this was the best video on using the heater I have seen, saved it so can watch again another time but you made it so easy to callow along. Great work 👏

At long last, finally stumbled across the one I needed, I really appreciate you taking the time to post this tutorial,in a slow,and repetitive nature,to allow my three brain cells to absorb this valuable information. Thankyou.

Bloody fantastic video. Just installed my heater and was scratching my head on how this control works. You have made a great video that explains things that everyone can understand.

Thanks Mic, knowledgeable information. I've just done a test run in garage and all good. So I'm now confident to go to full boat install. I'll keep watching new developments.

Thank You. I just replaced mine heater and the new one has this very controller. Excellent job showing us how to get around this controller. Great video

this is the best explanation of hopw to operate this version of controller- been searching for this for weeks- well done- very clearly explained- Thank you!!😊👍👏

The best video I’ve seen for screen information, well explained and didn’t talk that fast you couldn’t understand it.

Thanks mic, I scratched a lot of hair before I found this…I was following instructions for a very similar looking controller, and I couldn’t prime my new install, until I found your video. It did worry me, I went back and checked all my wiring etc…..only to find that there were two similar controllers, that work completely differently.😜

Thanks for making this video. some great info that's almost impossible to get from the manual.

Thank you for this detailed video, this was a tough one to find. Now I get the controller process and I've saved your vid to share and reference.

This is absolutely helpful information I thought my controller was broken turns up I didn’t know how to properly use it looking at other videos I was getting wrong information because the controllers looked identical again thank you so much now I can sleep at night ;)

@johnb2044

Жыл бұрын

had totally same issue, happy to go retry in the garage tomorrow and make better use of it

Best explanation of the newer controller yet, thank you!

This video kept me from returning this unit! I was watching similar videos with the same looking display, trying to get into the settings to adjust fuel mixture. Now I know it's not possible ( would be nice) but for now I'll give it a try and see what happens!

Mate! Right now my young family and I are parked up on the Donegal coast, being battered by a storm. Your vid just made the difference between me worrying about having to set an alarm; to wake up and turn the heater on and basically getting zero sleep, to just setting and forgetting the auto heater function. Thanks for taking the time to make this video. I owe you a pint!

Couldn’t pair my remote up for love nor money having fitted several night heaters didn’t realise there was a new controller so thanks to your video it’s all sorted keep up the good work😊😊😊

Very Thorough video, just made my life alot easier. Instructions are hard to understand & when I seen the high internal temp I thought something was wrong but now I know that is OK. Thanks so much

Thank you very much, thought mine was broken, finally got it running with your instructions!

Thanks for this great video. Previously I found a tutorial about the old type. Good man. I appreciate.

For 2 years i have been cooking in my van, always set temp but had it on manual mode, temp would go up to 30c + but now in automatic mode i set temp to say 15c its comfortable even though goes a little higher, great video thank you

thank you very much for this. I was pulling my hair out searching the internet for the set up. The book they gave me had the wrong controls. Your video provided all the information I needed to get everything working and and understanding of how to work and navigate the unit. Thank you.

@baza6127

8 ай бұрын

Hi, just want to add, to turn on the timer after youve set timer, hold settings and the up arrow.

Yes, what I found was the pump changed its pitch after a period of time and I took that as an indicator it was primed. I stopped the pumping and tried to start the heater and it lit right up. All is good. Thanks for the controller review lots of good info there. I was going to use just the manual settings but switched to Auto and I think that will be my go to setting.

@2005mic

Жыл бұрын

Good to hear all worked out fir you

Excellent video, was getting really frustrated with this controller and about to send it back thinking it wasn’t working now it is. Instructions that came with the heater ware not good. Thanks for sharing

I wish I had found this video sooner... it was super helpful!

Done a practice run install of my heater today and eventually got the electrics done tonight , however i was trying to prime as in the other videos , so will try this tomorrow. Thanks for the video

@hawk1481

5 ай бұрын

Yeah that’s why I’m stuck at right now

Thank you so much for this, i kept watching other videos and could not understand what i was doing wrong, different screen as you have high lighted

Thanks, you're the only one on the Tube who knows how to pair my remote control 😅.

Thank you so much for the video. I was not able to prime the line using the manual or other videos, using yours I was up and going in a matter of minutes.

I just had one fitted today and I have the same interface, great video and very helpful. Thank you!

you're a life saver. i got one of these last week and the manual is useless its for the old style.

If anybody finds out how to change the pump and fan parameters pleace share the info! Really great video!

@trevor.h

7 ай бұрын

I guess we can't set pump frequency anymore... and even though it has a temperature setting, it will never actually turn off when it reaches the temperature you set. Appears to just go down to it's lowest pump setting that appears to be 2.0 hz. ...Off to buy an old style controller while I still can.

@electriclightbulb1232

7 ай бұрын

@@trevor.hJust bought this stupid controller and spent all that money on a new board just to find out I can’t change pump speed

@jeffery6810

6 ай бұрын

I hate this controller it's sucks the that's not get hot like the last one its l blows warm air

@jeffery6810

6 ай бұрын

Can we change the motherboard back to the old style so we run the old style controller

@hawk1481

5 ай бұрын

@@jeffery6810 what does the old style controllers look like mines red can’t find any information on it. It looks like the piece for the fan and the H is for the pump.❓❓❓😅😅😂

Brilliant, there’s no danger I would have got my heater working if it was not for yourself 👍👍

Fantastic help, very kind of you to share this info, thank you.

Thank you for this vid I was at a total loss thinking I done something wrong

Thank u for posting this matches my controller 🎉

Thank you man. You made it so easy

Thanks for this video, Well informative gave me all the info I needed

Finally the right info for my model, fairly clear explanations but should improve the "focus" of the image, thanks for this video, grazie.

Thanks for the video I will now try to start my own heater .

You just helped me to pairing remote mate🔥🔥🔥thank you so much 🥃💪🏻

Great video. I am doing a video on the new Suitcase heater and it has this controler on it. I am going to refer my viewers to this video as it is so well done. I do have one thing that you missed. When in the H1 to H6 mode, if you press it one more time it will go beyond 6 and display the preset auto temp and it runs in the auto mode. Thanks for the video.

@2005mic

Жыл бұрын

Thanks for the info. I'll check it out

@bobamos3628

Жыл бұрын

@@2005mic Yes, let us know what you find. I know mine is doing it but we all know that there are so many of these controllers it can be confucing. Also, hope it is okay to link your video on mine..

@2005mic

Жыл бұрын

@@bobamos3628 yes that's fine to link my video. Thanks. Will get to mine next week to check out setting past H6

@bobamos3628

Жыл бұрын

@@2005mic Thanks. Here is a link to my video. kzread.info/dash/bejne/aolhzNWFqZzbh7g.html

@bernswonger57

10 ай бұрын

But temp can't be adjusted from there.

Hey thanks allot for the video. I have been struggling to get the timer going and most the videos in KZread deals with a different control panel version. Even though they look identical. All the best!

Thank you so much. Extremely useful video 👍🍻

Brillent video just what I was looking as most videos are the other controller thanks! :-)

Thanks dude that is very helpful !🔥

Excellent. So easy to follow

Appreciate this video. Helped a lot.

I have this control on the 3rd 5KW all-in-one (red slim case) I bought in January 2023 from VEVOR. The two physically identical heaters I bought before in 2021 and 2022 had what was called "new Blue-style controller" with the elapsed- time. I do not like this control - NOT because it's in any way difficult to use, but because it connects to completely differently-programmed controller! This controller start-up routine idles the fan super low, and turns on the glow plug. When the plug reaches temp, it does a fan pulse with 3-shoots of fuel from the pump and then drops the fan speed back again. Then starts pumping the normal H3 pump rate before gradually increasing the fan speed to a high rate. This results in too much fuel and white smoke during start up and a fuel smell escaping from the air intake for about 5-10 seconds - until the flame in the burner can be heard noticeably increased and the glow plug goes out. After that, the fan comes up to a mid-range blowing lukewarm air until it reaches operating temp at H3 by default and the blower settles in. At shutdown the glowplug comes back on and the fan is slowed to almost stop - running at idle for about a minute or so - apparently with the idea of allowing the additional the burner chamber to burn off more unburned fuel residue. Then after hearing the exhaust pipe ticking from the heat, the fan finally comes back up to a useable speed to complete the cooldown. The identical unit with the earlier "New Blue Controller" did not attempt to reach near overheat conditions by virtually shutting off the fan on an already hot burner chamber with a lit glowplug. Instead it turned the glowplug on with the blower going immediately to a high speed until cooldown was completed. During startup, the fan ran at a slow but still functional CFM while the glowplug was on. On reaching ignition temperature the pump was started at a high rate, the fuel ignited and the fan speed was increased to force more air through the chamber. The result was no exhaust backflow and faster operating temperature air discharged from the outlet. I do not prefer this new style controller at all. However, it is both the controller and controlboard (and possibly the harness wiring) that would have to be retrofit to convert it to the timer-type Blue controller. (Unfortunately this same controller format with "H3" on the display is also being sold in the original blue controller shell! It is not to be confused with the black or blue "00:00" ones!) The start-up and shutdown procedures programmed into this "H3" controller do not compare favorably against the "00:00". This was not an improvement.😠

Thank you very much for posting this video instruction. I just installed my heater and could not figure out how to set this thing. Just till I came to find out it was a new type, as you described it. Too bad, it does not have a time display but still a good deal. And now I know how to operate it the proper way. Works like a charm. Do you know by any chance if there are any other type of controllers that are suitable for this heater?

Awesome video. On this stuff i prefer an older grown up person who uses a pointing stick to make sure u cant get it wrong. No clickbait easy explanation keep up the good work please ❤

Great video. Finally found a tutorial on the controller and remote that I have. Thanks

Nice informative video! Thanks!

Very clear and informative. Many Thanks

Thank you so much pal this helped loads

Brilliant video mate thanks 🙌

Thanks for the video. I whatched it to make sure i found all there is...i found the timer tutorial useful, thanks. I have this and the "old one" heters... in the old one i could programm the glow plug to take less power in the start up...in this there are less options...allso this timer is more complex, and im a simpel man 😃.

@2005mic

Жыл бұрын

Yes the "old" one has more options. Usually "new" means, more and better, but it doesn't seem that way with this heater controller

Thanks for the video. Good info!

I agree Thanks for the Correct information. Great video!

To try and reduce coking do you agree with running it at a lower heat setting (not over H3) and in Alpine mode? To get the combustion chamber staying hotter as there is less airflow over it. I realise the pump speed and fan speed automatically adjust. But what else can we do? Crazy the “new” model doesn’t let you adjust pump speed! I seem to only get 10hr before the atomiser basket in wrecked. Great video! I’ve been looking and looking for videos on this new controller. Yours is about the only one!

Thanks this video is a big help.

Great info. Thanks. AJ

Great video fella

Have my first heater, you have saved the day; brill

Kero added to the fuel, does that clear existing coke or only reduce new coking? I was thinking of running a high kero mix occasionally. What percentage? I heard these pumps need diesel to lubricate them, so they wear out fast running on straight kero.

Thanks very informative perfect ❤

Awsome Thank You SOOOOO Much!

Thank you!

Thank you great video

hi Mic, I don't understand the setting auto timers, can you do video for this section only , thank you

thank you for the information like to set timer on display to turn off so it will not burn out display

The missing switch left centre that is not installed just seems to prime the pump, same as up down together. It offers no extra function when long pressed with any of the other buttons.

legend.

Omg.. you saved my life

Great video, thank you,

Well done Sir 👍🙏

perfect video

Thanks so much for this

Thanks from Canada

Great video Mic, thanks. This is the best tutorial for these 'new' controllers. I got one of these with my '8'kW heater from Vevor recently. It works well but there are some doubts as to the effectiveness of the Temperature control mode in cutting back the burn rate once temperature is reached. There is a secret menu if you long press OK and On/Off buttons. It brings up a 3 digit PIN code screen but so far I don't think anyone has hacked it yet. Someone suggested 168 but I don't think it's right.

@2005mic

Жыл бұрын

Thanks. Yes setting the temp to Auto mode, it does work well just seems a bit slow to adjust to measured temp. I'm working on the code, will update if I find it

@andrewboese3541

Жыл бұрын

These 'new' controllers are a real nuisance. The old one with the 1688 password was a much more customizable controller.

@Toob41

Жыл бұрын

I just run mine on H1-H6 and it's OK. I guess we'll get the code eventually.

@mickeniotusen

Жыл бұрын

@@2005mic it is great. Like my oem Eberspächer it is also slow. No need for fast action at all. It adjust the temp more accurate and is more stepless with the fan.

@ryanfish1137

Жыл бұрын

Any word on the 3 digit pin!? My diesel heater is angry. I have it plugged into a 12volt outlet and it's unhappy. Says the voltage is to high, even though max voltage in manual is 16volt for the 12 volt model.

Just purchased an all in one Vevor heater hoping to heat my Van for the winter. This is great information. Can you change C degree to F degree in the settings some place. Thanks for your help.

@2005mic

Жыл бұрын

Not that I'm aware of sorry. These controllers seem quite basic. If I find something I'll let you know

Good job.

Thanks Mic, this video helped me with everything the manual did not state to good, but is the auto dim feature an option? My controller does not do that. Do you know if that is an option?? Thank you, good channel.

Question an what body temperature runs the heater ? On diverent power level ,the mine is on h1 or h2 under the 80 degreece an shut of

@2005mic

Жыл бұрын

Depends on size of room. As it’s a manual setting it will heat at a constant rate. If small room it will just get hotter. Set it onto automatic by pressing and holding the “setup” button to set a specific temperature. It will then hold the room at the set temperature

I already had two of these heaters with the blue display. Working as expected, I'm fully satisfied with them. They heat up to 210 - 212 Celcius on level 8. Then I bought another one and it has this black oblong display. Turns out this has only six levels in stead of eight. Np problem, but this heater does not get hotter than 184 Celcius. Is there a way to crank it up higher to at least 200 Celcius?

@johntartaggia2191

8 ай бұрын

I have same question. Is the black one too dumb to improve? Blue one and its ECU much hotter.

Hi, do you know the Code for the administrator Settings. I want to raise the frequency from the fuel pump.

Do you know if there's a way to tune the fuel mixture like there is with the controller that looks like this? Because mine is running super rich and blowing a lot of smoke

@2005mic

Жыл бұрын

No. Can't adjust fuel mix. Others say it's auto regulating. Run it for an hour on high and see if it clears

Thanks for the video, how do you enter (advance) menu on this?

Hello!, I got this new model few days ago. The problem was that i was trying to lover the "H3" to "H2" and it litteraly just stopped and said "E-05" So i checked the manual and it said it was overheating, but machine just stopped without cooling it down and i was letting it to cool down and when i pressed "start" again it said E-06, i have been the owner only few days.. i also have a old model wich had same error, but i bought new fan engine and still same problem..

Ty for info but my controller looks similar the steps you outline don't work.any info suggestions for units sold in US? I seem to be behind an access code that's not provided despite 2 calls to seller I saw on another video a code of 1688 but it doesn't work on my unit. Any help is appreciated ty.

@2005mic

Жыл бұрын

Sorry not too familiar with other controllers. They all look very similar so may be the rmolder controller.

How do i change the actual temperature? Its always blowing really hot and in manual mode ive been trying but it does nothing.

Is there any way to switch from Celsius to Fahrenheit?

Hi Mic, thanks for your informative video. Can I ask a question? I have the same 3 fan blade LCD with the round Settings button symbol, not the spanner symbol. I see that your max. case temp. was 178 Deg.C, and mine is about the same, 176. But my prev. heater, a Hcalory 2Kw (with blue LCD screen) gets to about 230 Deg.C. and so I need to find out why this one has far less heat O/P, and if any changes can improve it? I know that the LCD and ECU are a matched pair, but should I expect more from this heater? Thanks.

@2005mic

8 ай бұрын

That temp is the highest I have seen so I would say that is it’s design range. Different heater brands may have different temp ranges depending on their construction.

Hi Mic, I just got the vevor and it has the same controller I watched a few videos on pairing, I hold the up button but it doesn't change to HFA ?

@2005mic

Жыл бұрын

Did you sort it out. This controller is different. Watch the video again where it explains the remote control, it’s pretty simple

Hi Mic, is there anyway of showing Hz on the display? If not is there a way to work out what H-1 is in Hz so I can work out the diesel usage. Is H-1 equal to 1Hz and H-2 equal to 2Hz etc etc Thanks Dave.

@2005mic

Жыл бұрын

Hz is not available on this controller. To work out usage you would need to wait till heater has come to temp on each of the H1-H6 settings, count the pump pulses for 1 minute, and multiply by pump delivery amount, 0.02ml. Hope that helps

@cooltube

Жыл бұрын

@@2005mic thanks Mic, sure does.I get it to 144lml /hr on H1 (2pulses per second)

Hi, great & informative video - thank you! With the remote control can you change it to turn on in auto mode rather than manual? Thank you!

@2005mic

Жыл бұрын

Unfortunately no.

What does the red circle with a dash through it mean on the bottom left of the LCD screen?

@2005mic

Жыл бұрын

Just an indicator. Has no real function

Just thank you

Thank you very much for your informative video. QUESTION. Last night I tried firing up the unit but I didn't understand the buttons at that point, consequently I seemed to have over-primed the unit and when I set it in motion and it went into the heat stage I had an absolute smoke screen outside the van. I shut down the unit and I'm not a bit lost as to restarting the unit! Any suggestions would be appreciated... Cheers Brian

@2005mic

11 ай бұрын

Yes machine is flooded. Run it in alpine mode and let it run till smoke clears. I'm assuming it was white smoke. Alpine mode reduces amount of fuel it pumps