Thnak you so much for this video, i took my car to the shop and they told me that my car needs a new timing chain kit and that would could my $2250 for parts and labor, but after watching this i ended up only spending a $100 to get the tensioner replaced and its working perfectly fine now. Thank you again Mayo Cars DR

@MayoCarsDR

Жыл бұрын

you welcome,Thanks for comment

@foolishdreamer701

Жыл бұрын

Looks like they tried to rip you off....

@ashikchesust

4 ай бұрын

I checked it out. They also told me like 2200. Where can go to do it at cheaper price?

@ashikchesust

4 ай бұрын

Thanks. Changed the tensioner. During acceleration engine was getting very loud. Still the same.😢 Sound is there. Also check engine light came on. Any idea? I have exactly the same problem as you showed.

Thanks, my Yaris suddenly sounded like this today at 260,000 km. Idles fine, only hear it when I am driving and accelerating. Pretty sure it isn't water pump, and I know it isn't the bearings in alternator. I will give this try. I appreciate you taking the time to record the sound. Very helpful. Edit: I discovered that the 1.5 engine in a Yaris/Echo has an internal tensioner that is not the same as Corollas, Matrixes etc. One of the dealer techs agreed my engine sounded like a timing chain, but he'd also heard water pumps make this noise and he has never replaced a chain or tensioner on the 1.5 engine. So, I went for it today and jacked it up, and took the serpentine belt off. Yup, i could feel the rough bearing on the water pump right away. So, if others come across this sound, you can quickly narrow it down by removing the serpentine belt and feeling the alternator, water pump, and AC compressor bearings. If they feel a little rough or make any noise as you spin them, that's probably the culprit. If you can't tell, start the engine up for a minute with no belt and listen. If the sound is still there it isn't bearings driven by the belt - it is likely the timing chain slack hitting valve cover or dampener. I replaced the water pump as described by others and all is quiet again. Was about a 3 hour job and a little difficult to get at with big hands.

@MayoCarsDR

2 жыл бұрын

Thanks for comment

@makeit.primetime99

Жыл бұрын

Hey thanks for the comment, i have the same yaris 1.5 2009 and was wondering about this, I have replaced my water pump, so the tensioner in the yaris is different?

@redgreen610

Жыл бұрын

@@makeit.primetime99 When I removed the belt to water pump and turned it I could just barely feel rough bearing. When I started it up without pump connected, it was silent. It was the bearing after all. I was so sure it was the tensioner, that I'd ordered one one from Toyota. As soon as I saw it, I realized it was completely different. That 1.5 Yaris engine has an internal tensioner that is much more difficult to replace and that's why there are no YT videos on it. You have to pull the pulleys and timing chain cover off to get to it. So, I returned it at 10% restock charge, went to the local part store and bought a water pump. OOps so long ago, I forgot I've already gone through this above.

I had this same noise on my k24 and I changed the timing chain tensioner and the nosie is gone, thank God. Next I'm changing the vtc actuator gear plus timing chain, tensioner and guides

I'm having similar symptoms of engine noise after 2k rpm, the fiat Punto MjD, clocked 3.52 lakhs kms. Will check with chain tensioner. Thanks for the video

@MayoCarsDR

2 жыл бұрын

Thanks for comment,If you have a 2ZR engine, only the tensioner can be damaged. This engine has this problem

Very Helpful video, mine 2ZR 1.8 has the same noise under the same condition, will replace the tensioner. Thanks a lot!

@MayoCarsDR

2 жыл бұрын

Thanks for comment

@noahriedel801

2 жыл бұрын

Did the tensioner solve the noise ?

@JoseManuelCastillodamboo

2 жыл бұрын

@@noahriedel801 yes, it work.

@letmethinkv

Жыл бұрын

@@MayoCarsDR bro did you re use old valve cover gasket or new?

@MayoCarsDR

Жыл бұрын

@@letmethinkv It is best to use new gasket

0:53 9:54 comparison

Thank you for this informative video. My car also makes the same sound when starting the engine, will replace the chain tensioner

@MayoCarsDR

2 жыл бұрын

You welcome

Thank you Brother. Huge help.

@MayoCarsDR

8 ай бұрын

You welcome

Good job broz very informative for people looking for same symptoms. Doing also automotive basic Pms and repair maintenance., But inthe other channel. Going to check your other vids bro 👌

@MayoCarsDR

2 жыл бұрын

Thanks for comment

Cool slow house music wasnt annoying. Good vid ty.

@MayoCarsDR

2 жыл бұрын

Thanks for comment

@-mayorka-

Ай бұрын

​@@MayoCarsDRname song plz

log pakistan ma pagal banatai ha is awaz per puri timming chain vvti sub kuch change kr deta ha ya sir tensioner ki awaz hoti ha ap sirf wo replace kr lo ga awaz gayab ho jati ha ..goood work brother nyc information

@MayoCarsDR

2 жыл бұрын

Thanks for comment

Good job its a great work

@MayoCarsDR

Жыл бұрын

Thanks for comment

Good

Very well understood, nice video

@MayoCarsDR

6 ай бұрын

Thanks for comment

Thanks so much found the video very useful, just replaced mine and the noise has gone away

@MayoCarsDR

Жыл бұрын

Thanks for comment

Nicely done.

@MayoCarsDR

Жыл бұрын

Thanks for comment

This looks like it could be the same for 1.5 1nzfe? I'm starting to suspect my car has this sound but I never noticed

Very good KZreadr

@MayoCarsDR

Жыл бұрын

Thanks for comment

Muy Bien video ...gracias ,una pregunta ,cuando pones El chain tensioner ,no necesitas mover El crankshaft para que queden. Posicionados Las valvulas ..y la varilla del tensor tiene que quedar afuera o en su posicion normal ...gracias de antemano

@taz24787

9 ай бұрын

Al parecer el tensionador se coloca con la varilla (embollo) adentro y enganchado. A la hora que giras la cadena con el crankshaft manualmente, se libera el embolo cuando suena ese "click" que se demuestra en este video.

My car started making a slight noise on start up when the engine is cold.it stared after I changes the oring on my chain tensioner but I didn't put it back in at tdc could that be why. And I also when and bought a new tensioner from toyota today to see if it helps bur it still makes the same noise.its on the 1zz engine

Good video--thanks

@MayoCarsDR

4 ай бұрын

You welcome dear

On my 2010 Toyota Corolla repair manual said to release tensioner hook turn crankshaft to counterclockwise then clockwise. Now I have 2016 Toyota Corolla 2xr-fae should turn clockwise to release the hook

Brother my carolla 2017 making a ticking and knocking sound while acceleration and cold temp. I can barely hear this but it’s there and it’s annoying any idea what’s casting this sound?

اهلا هل يسبب هذا الجزء فقدان ضغط زيت المحرك او يعمل على تهريب الضغط

😊👍

Hi,I have 1zr Fe 1.6 liter engine ,having same problem,changed timing chain tensioner but sound still exists.what should I do?

I had the same sound and checked the timing chain tensioner, The plunger was stuck back in the body of the tensioner and the body was also cracked along its length. I am sure it would have broken along the crack lines and fallen into the engine. I replaced it and the noise is gone. But now, I have a whistling sound coming from the engine.

@selman044

Жыл бұрын

Did you get rid of this problem. If you didn't, here I am gonna tell you something. Because the timing chain tensioner failure, probably your engine's timing valves got into some different gaps. Check your valves' gaps, probably they need adjustment.

About engine movement, maybe a bad engine support?

Thank you so much for your helpful videos 🙏 What kind of product do you apply to the tensioner gasket, and is this the same product you use on the valve cover gasket?

@MayoCarsDR

Жыл бұрын

Yes

@janoycresva9903

Жыл бұрын

@@MayoCarsDR What is the product called?

I can’t afford to fix until end of week I have same problem will I be fine?

Music was too loud and unnecessary. More importantly you totally failed to mention. The engine crankshaft must be turned CLOCKWISE to allow the tensioner to extend to the proper length. It's in the instructions of the tensioner.

My 2nz 1300 cc engine also this noise is this a same issue sir plz reply???

One question to turn the crankshaft should the car be raised from both wheels? my car is a toyota corolla 2010 1.8

@MayoCarsDR

Жыл бұрын

No need to lift any tires to rotate the crankshaft

Mine has started to rattle just on start up. Changed oil and it stopped for a little but it's back again. I'll try change the tensioner.

@MayoCarsDR

Жыл бұрын

Thanks for comment

Looks like it also needs a motor mount.

A1

Hi, I have a question. What were you doing at the 4:27 - 4:47 mark? Thanks and great video!

@MayoCarsDR

2 жыл бұрын

I was checking how loose China is

@oriondragos5876

2 жыл бұрын

@@MayoCarsDR ahhh ok thanks

Not clear on new verses the old check of the tensioner. Not clear on the rotation to TDC.

is it a typical problem of toyota engines? why does the tensioner fail? Greetings from ARGENTINA

You need motor mount too

Other than rattling noise when in Driving, would there be any check engine light's error code? Thanks for the video.

@MayoCarsDR

2 жыл бұрын

There will be no error code,

@callmebackfriday2

2 жыл бұрын

@@MayoCarsDR Thanks for the information.

@MayoCarsDR

2 жыл бұрын

But if the slipper of the chain also breaks after the tensioner is bad, then the timing is out, then the check light is on.

@callmebackfriday2

2 жыл бұрын

@@MayoCarsDR Thanks again. I possible will notice the noise different but for my wife, I pretty sure she will keep driving until smoke come out from the hood.😜

Hi, is it better to put gasket maker (I want to use permatex ultra black) directly on tensioner mating face, or apply it on the black washer/gasket?

@MayoCarsDR

9 ай бұрын

Apply on the black gasket

@jacobd3290

9 ай бұрын

@@MayoCarsDR Thanks for fast reply. But what about the mating surface between tensioner and gasket on the outside? I am worried the gasket will only seal on the inside to the engine, but not on the other side between tensioner and the washer/gasket

@jacobd3290

9 ай бұрын

@@MayoCarsDR I see now on video that you put grey gasket maker on both sides of the black washer/gasket

any idea if the raised lip on the timing chain tensioner gasket goes towards the engine or away from it? Thanks

@MayoCarsDR

Жыл бұрын

kzread.info/dash/bejne/lYyjxJWElKy3eNI.html 6:17

@MayoCarsDR

Жыл бұрын

Engine Rebuild Repair Manual

Cool. Would you recommend replacing tensioner at 193k miles on 1ZZ-FE engine? Chain did seem a bit slack when changing valve cover gasket and there is a tiny 1 second rattle on cold start. I've heard it could also be the phasers. Car runs perfectly otherwise. Doing 5k OCI with full synthetic. Thanks.

@MayoCarsDR

2 жыл бұрын

Thanks for comment,The 1zz engine has no tensioner problem with this but if your car has traveled long enough you can change it.

@MarzNet256

2 жыл бұрын

@@MayoCarsDR Thanks

@drdelirious8899

7 ай бұрын

@@MarzNet256it’s not true 1zz has problems with the oring on the tensioner and can fail it failed on mine look behind motor and see if it leaking

@MarzNet256

7 ай бұрын

@@drdelirious8899 I checked it about 6 months ago, no leaks. The VVTi solenoid O-ring did have a tiny leak, so I replaced the solenoid/o-ring assembly.

Just ordered my tensioner, i have leak on mine and the mounting plate on my tensioner is completely rusted. It should make this rattle go away

I had corolla 2013 same issue Should I replace vvt cam gears also as i already purchased them please advise

@MayoCarsDR

5 ай бұрын

Yes

My Corolla engine is 2NZ-FE and the tensioner is inside the engine. Can I change the tensioner while the engine is on the car or should remove the engine completely

@MayoCarsDR

Жыл бұрын

You can change the tensioner without opening the engine

الترجمه للعربيه

Question ❓ I'm just trying to replace the gasket on the *timing chain tensioner!* (It has the only oil seepage I see on the whole entire engine) is it necessary to pull off the valve cover, and as an engine have to be top dead center?

@MayoCarsDR

2 жыл бұрын

It is not necessary to remove the valve cover, but it is better to fit the crankshaft pulley at zero mark.

Are change oil with 5w30 fix it?

@MayoCarsDR

2 жыл бұрын

This engine already has 5w-30 oil

Hello, in my toyota 2znfe with none vvti 1290 cc timing chain is slack what the problem is? Chain, sprocket or tensioner pls advise.

@MayoCarsDR

Жыл бұрын

It is difficult to tell without hearing the voice

@jaymungle9959

Жыл бұрын

Engine mileage is 230000km oil use 20w50 shell. Last year I renew the tapper cover gasket and notice that the chain is loose a little.

I wish I k ew this two days earlier. Just now KZread started to suggest them to me. KZread algorithm has failed me. I paid $700 in total to fix it with used spare parts otherwise it would be skyrocket cost.

@MayoCarsDR

Жыл бұрын

Thanks for comment

Seems like it also needs engine mounts.

Does this cause low power... My 2004 xb with 277,000 mi is sounds like this is

@MayoCarsDR

Жыл бұрын

Yes because VVTI does not function properly due to this

Hi brother how are you can you help me i have toyota corolla rpm problem i check timing chain all fine but problem is not sold

@MayoCarsDR

Жыл бұрын

When did this problem occur in your vehicle?

at 9:09 time in video. when engine starts first time , there is rattle sound of vvti . it is normal? i have same engine when start cold engine rattle sound for 1 sec coms from engine.

@MayoCarsDR

2 жыл бұрын

If the VVTi system is OK then the sound does not come

@femiamosu6953

2 жыл бұрын

You might have a damage vvti cam phasor

4zz-fe. Chain start to rattle after 5w30 regular change. Chain rattle after 1000rpm. Stop rattle under 1000rpm. I suspect the tensioner, but when i check it it was perfect. Any ideas?

The music makes it hard to hear the sounds you are listening for

@AllenMemeson

2 жыл бұрын

Do you not hear the ticking/rattling

@yodead369

2 жыл бұрын

Sounds like he's playing "Rush", on N64 😂

It is same 2nz ,2010 model I have changed tensioner . Novice not remove for my car. ?

@MayoCarsDR

2 жыл бұрын

Thanks for comment,You should first assess the sound of your vehicle where the problem is

@MsSajid83

2 жыл бұрын

@@MayoCarsDR thanks replying mechanics says change engine

@MsSajid83

2 жыл бұрын

@@MayoCarsDR please suggest me I have a change engine and change the gear box 6 speed transmission manual it is a possible or not I am waiting for your reply thank you

@michaelgerhart1888

2 жыл бұрын

@@MsSajid83 your mechanics could be wrong. If it’s just this rattle and not knocking noise it’s probably the cam gear. It has a TSB. Do some research.

What is that "rattle" noise #1 @9:07 and high pitch noise at the end of #2 @9:14. Is that starter issues? Thanks

@Fm-qf5dj

20 күн бұрын

Vvti gear

There’s any reason why did you remove the top engine cover? Is it necessary to remove?

@MayoCarsDR

2 жыл бұрын

Thanks for comment,Remove the valve cover simply because when the chain tension is bad, the small chain sleeper on top of it also breaks, to check it.

When my car on road rpm 1500 to 2000 then adjustor noice come. In 3 year i changed 3 adjustor any solution 😔

@MayoCarsDR

2 жыл бұрын

In addition to Chain Tensioner, check out Chain Sleeper،5:21

Turn clockwise or counterclockwise to hear click sound?

@MayoCarsDR

6 ай бұрын

Yes Ok

Same problem i got

@MayoCarsDR

2 жыл бұрын

Thanks for comment

is timing chain tensioner exist in 1nz-fe engine ?

@MayoCarsDR

Жыл бұрын

Yes

Timing chain tensioner in VVTi engine always produces noise on cold engine startup for a few may be 5 secs and some times less than that even after some hot engine startups. Kindly comment

@MayoCarsDR

2 жыл бұрын

In this case, the VVTi gear or chain tensioner may be damaged

@bernardrukwaro1585

Ай бұрын

Same to all vvti engine with 300000 mileage and above

i start the car than put D mode rpm coming down 700 then change parking mode rpm 1000. 1500 after very long time coming down please help me brother

@MayoCarsDR

Жыл бұрын

Clean the throttle body of your car

@MayoCarsDR

Жыл бұрын

And rest memory

@MayoCarsDR

Жыл бұрын

kzread.info/dash/bejne/nYiKzKeIfNexlaw.html

Where are you from my dear brother? 😊

@MayoCarsDR

2 жыл бұрын

I am from Pakistan

@user-zq3ub5cm1s

2 жыл бұрын

@@MayoCarsDR ماشاءالله تبارك الله 😊👍

@user-zq3ub5cm1s

2 жыл бұрын

@@MayoCarsDR To you, my dear brother, greetings to you and my family, Pakistan 😊👍

How much is the usual cost to change the timing chain and tensioner set? One mechanic asked for 2200. Is it that much costly?

@MayoCarsDR

4 ай бұрын

2200 ?

@ashikchesust

4 ай бұрын

Yes man. They asked for $2200, isn’t it too much?

I bet you can't diagnose my 2003 Toyota matrix that's sending code p300 and sounding the way it does wit the video a send to you if you read my comment and reach out if you do I'll subscribe just ask for the video. When you do diagnose the problem do a KZread video complimentary of me it's all yours, I'm waiting.

@MayoCarsDR

11 ай бұрын

The P0300 engine code indicates a misfiring cylinder problem in your vehicle. The misfiring happens when insufficient fuel is burned or when the spark plug gets damaged. In addition, it can damage your car's catalytic converter in extreme conditions.

السلام عليكم قمت بتبديل بآكن الرأس ولكن بعد تطبيق المكينة اشارت لمبة التشيك فحصتها عند كهربائي سيارات فقال ان التيمت غير موزون ولكن السيارة هادئة وكل شيء فيها طبيعي .. ما هو سبب إضاءة لمبة التشيك برأيك ............. Peace be upon you, I changed the head machine, but after applying the machine, the Czech bulb indicated that it was checked by a car electrician, and he said that the timt is not balanced, but the car is quiet and everything in it is normal. What do you think is the reason for lighting the Czech bulb

@MayoCarsDR

5 күн бұрын

Code?

what this sonung

@yannaing693

2 жыл бұрын

hi

Brother my carolla 2017 making a ticking and knocking sound while acceleration and cold temp. I can barely hear this but it’s there and it’s annoying any idea what’s casting this sound?

@MayoCarsDR

6 ай бұрын

How many kilometers has your car driven?

@MayoCarsDR

6 ай бұрын

Can you send me a video?