Bonne chance et bonne continuation Merci beaucoup 👍👍👍👍👍

@MrRicoh

3 жыл бұрын

Thank you. Our latest movies are even better quality and have subtitles. I invite you.

Good job

@MrRicoh

3 жыл бұрын

Thank You

Faz um vídeo mostrando como é a unidade developer por dentro, desmontando ela

@MrRicoh

3 ай бұрын

Salvei seu pedido, talvez possamos fazer isso.

thanks,,,,,

@MrRicoh

Ай бұрын

@kourushsafari Welcome

O erro c5603 pode ser causado pela queima dessa placa PWB-FR?

@MrRicoh

2 ай бұрын

Sim, esse pode ser o motivo.

Helpful video!! I have two bizhubs, a c454 and c554e. Is it possible to remove the cyan one (needs changing) from the c454 and replace it with the much newer one, which is in the c554e? Will it all register and sinc up ok?

@MrRicoh

8 ай бұрын

Hi, The most important thing is the appropriate grammage, you need to pour exactly 180 gr.

@ryanhill4091

8 ай бұрын

Can I just swap the whole developer unit, as I have a feeling the one in the c454 is faulty. The developer unit in the c554e is almost full I think

@MrRicoh

7 ай бұрын

This way you can replace the entire module. Just remember not to spill the developer powder. Be sure to write whether you succeeded with this operation. Best regards and I am waiting for your reply.

@ryanhill4091

7 ай бұрын

@@MrRicoh it was a success. All worked fine, BUT, my test page has too much cyan or green washed through the colour chart. Any solutions for this?

@ryanhill4091

7 ай бұрын

@@MrRicoh so basically, it fixed the huge cyan strip through every print, but the cyan output appears to be too heavy. I changed the charge output in tech mode to -2 cyan, against the Black magenta and yellow, but this didn’t change or fix anything

Good afternoon my friend, how are you? Do you have a video demonstrating the replacement of the sponges and seals of the konica line office. I have a piece of equipment that needs to be replaced, the sponge that makes the belt shim.

@MrRicoh

2 жыл бұрын

@Mx3 Design I do not understand what you wrote. Is it about the elements in the fuser unit?

Hi! installed new developer unit and When printing, a whiter strip appears at the edge of the sheet. When you take out the developer again, you can see no developer at the end of the cylinder. Is there a lack of voltage or something?

@MrRicoh

Жыл бұрын

You have to submit a claim for developing

Hey, I’ve a develop ineo 284e. Do u know if it is possible to upgrade it to cmyk?

@MrRicoh

Жыл бұрын

It's impossible

Hello, God Bless you, could you tell me where I can get the Mailan of the Developing Unit of a Konica c224

@MrRicoh

11 ай бұрын

The whole unit costs over $400 so it's very expensive. It's better to regenerate, or put in a new developer and chip. See it in my shop: copy-expert.com/pl/c/Deweloper-Unit/228/1/default/1/searchquery/c224 Good luck I encourage viewers to support my channel: kzread.info/dron/OHtXTtGHj33pUm8Gf2FH3A.htmljoin Videos only for supporters: kzread.info/head/UUMOOHtXTtGHj33pUm8Gf2FH3A

May God give you to please you

@MrRicoh

3 жыл бұрын

Thank you.

There's no need to take out the front door. It doesn't interfere with the lower panel. Just saying..

@MrRicoh

Жыл бұрын

Thank you for this information. I didn't know about it. I'll try to follow your instructions next time. Best regards thanks.

Good day sir, please sir am having issue with my Konica c554. I simply remove the developer from the developer unit and flush out the old developer and fill it with new developer and after that I install back the developer unit. Now when I print or copy, it see the developer spilling heavily on the drum/image unit which affects print papers and copies. Please I need your help and solution on this issue. Thank you sir

@MrRicoh

2 жыл бұрын

There is only one question. How much are you pouring a developer? How many grams?

Konica minolta c754e erreur code c-3b08

@MrRicoh

2 жыл бұрын

Code: C3B08 Description: IH input voltage error • While the IH heater was ON, input power was at the high voltage detection value or over for more than the predetermined period of time. • While the IH heater was ON, input voltage was at the low power detection value or under for more than the predetermined period of time Causes: • IH coil unit (IHC) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) Remedy: 1 Check the connection of the fusing unit. 2 Check the fusing unit, IHC, IHPU, NF1 and PRCB for proper connection and correct or change as necessary. 3 Check the marketing area of the fusing unit. If the marketing area is incorrect, replace the fusing unit for proper marketing area. 4 Check the marketing area of IHPU. If the marketing area is incorrect, replace IHPU for proper marketing area. 5 Replace IHC 6 Replace IHPU 7 Replace PRCB 8 Replace NF1

Konica minolta c654e erreur code c-2556

@MrRicoh

2 жыл бұрын

Code: C2556 Description: Abnormally high toner density detected yellow TCR sensor The TC ratio of the toner determined by the toner replenishment control is detected to be the predetermined value or over for consecutive times. Remedy: 1 Reinstall developing unit. 2 Reinstall toner cartridge. 3 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16, CN10 for proper connection and correct as necessary. 4 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 5 Replace the developing unit. 6 Replace FRB. 7 Replace PRCB.