Finished up the head, governor and did the tune up on the 2-53.:)
Жүктеу.....
Пікірлер: 22
@davidetroitdieselnaveia8937 Жыл бұрын
Full Power!!!!!!!!!
@detroitgarage9430
Жыл бұрын
All 40-45 HP.:)
@wazza33racer Жыл бұрын
Lookin forward to the Dyno session )
@PeterGort2 жыл бұрын
…and it starts without hunting! Beautiful!
@detroitgarage9430
2 жыл бұрын
That was a surprise to me, I realized after the video I never set the buffer screw.:) I turned in out by 1/2 an inch for the tune up and didn't have to reset it.:) Thanks for watching.
@prevost86862 жыл бұрын
We have to order Delo 100 or T1 down here in the Southeastern U.S. It’s not stocked anywhere anymore.👍
@detroitgarage9430
2 жыл бұрын
I used to order the T1 as well, but a local store now stocks it.:)
@rodneymiddleton96242 жыл бұрын
First!!!! Bring on the first start video!!!! Thanks!
@detroitgarage9430
2 жыл бұрын
:) Thanks and thanks for watching.:)
@rodmanrodgers714611 ай бұрын
You have the best detroit vids. Do you have any setting the gap for idle? I have a 353 that dies at idle when steering the wheels load.
@detroitgarage9430
10 ай бұрын
Thanks, I don't have one for setting the gap. .002"-.004" @ 1100-1300 rpm. I'll do one when I finish installing the 2-53 into my forklift. Been meaning to do one for the sw-vs governor.:) For the DW-LS I've used both the running method and the static tool to set it. Both work well.:) Thanks for watching.:)
@rodmanrodgers7146
10 ай бұрын
@detroitgarage9430 The one I have is a DW LS. Gov #5107132. I've never tried with it running or a static tool. If you rebuild for customers, maybe we'll send some to you!
@johnbrotherton4076 Жыл бұрын
nice vid especially on the valve and inj height, but not much detail on setting the racks. Do you have a better vid on that? or could you make one or direct me to some good instruction? thanks
@detroitgarage9430
Жыл бұрын
Thanks, yes I have a couple more, one for a 3-53T and 4-53T. Thanks for watching.:) Here's the 353 sw-vs, rack starts at 20:59.:)kzread.info/dash/bejne/mImGzY-GfdKodKw.html 4-53T:kzread.info/dash/bejne/p6p8p85qnLO3h7A.html
@spencerhigdon1428Ай бұрын
How do you get more power out of these
@detroitgarage9430
Ай бұрын
Depending on how much power you need they can make around 60 HP with a good tune up and injectors. I have mine tuned to around 35-40 HP for the forklift.
@doorcountybywater2 жыл бұрын
I noticed you set the governor gap when the engine was not running. Can you set the gap on a limiting speed governor the same way? The service manual states to hold the rpms between 800-1000 while setting the gap but it’s very challenging and I’m hesitant to attempt to adjust it.
@detroitgarage9430
2 жыл бұрын
On a LS governor you set the gap with the engine running. There is a tool that was made to set the gap while engine was not running. I use the static tool mostly as the results are the same as doing it with the engine running.:) I'll check today and see what the static gap is.:)
@doorcountybywater
2 жыл бұрын
@@detroitgarage9430 thanks! We have a commercial boat powered with 4-53’s and I believe we need to adjust the governor on one of the engines because the rpms bog down under idle load. From my research it sounds like a gap adjustment but I’m nervous to attempt it.
@detroitgarage9430
2 жыл бұрын
@@doorcountybywater Yes, that sounds like the symptoms. It's not such a big deal to set the gap, you just have to mind the engine rpm.:) I would recommend a full tune up before you set the gap.
Пікірлер: 22
Full Power!!!!!!!!!
@detroitgarage9430
Жыл бұрын
All 40-45 HP.:)
Lookin forward to the Dyno session )
…and it starts without hunting! Beautiful!
@detroitgarage9430
2 жыл бұрын
That was a surprise to me, I realized after the video I never set the buffer screw.:) I turned in out by 1/2 an inch for the tune up and didn't have to reset it.:) Thanks for watching.
We have to order Delo 100 or T1 down here in the Southeastern U.S. It’s not stocked anywhere anymore.👍
@detroitgarage9430
2 жыл бұрын
I used to order the T1 as well, but a local store now stocks it.:)
First!!!! Bring on the first start video!!!! Thanks!
@detroitgarage9430
2 жыл бұрын
:) Thanks and thanks for watching.:)
You have the best detroit vids. Do you have any setting the gap for idle? I have a 353 that dies at idle when steering the wheels load.
@detroitgarage9430
10 ай бұрын
Thanks, I don't have one for setting the gap. .002"-.004" @ 1100-1300 rpm. I'll do one when I finish installing the 2-53 into my forklift. Been meaning to do one for the sw-vs governor.:) For the DW-LS I've used both the running method and the static tool to set it. Both work well.:) Thanks for watching.:)
@rodmanrodgers7146
10 ай бұрын
@detroitgarage9430 The one I have is a DW LS. Gov #5107132. I've never tried with it running or a static tool. If you rebuild for customers, maybe we'll send some to you!
nice vid especially on the valve and inj height, but not much detail on setting the racks. Do you have a better vid on that? or could you make one or direct me to some good instruction? thanks
@detroitgarage9430
Жыл бұрын
Thanks, yes I have a couple more, one for a 3-53T and 4-53T. Thanks for watching.:) Here's the 353 sw-vs, rack starts at 20:59.:)kzread.info/dash/bejne/mImGzY-GfdKodKw.html 4-53T:kzread.info/dash/bejne/p6p8p85qnLO3h7A.html
How do you get more power out of these
@detroitgarage9430
Ай бұрын
Depending on how much power you need they can make around 60 HP with a good tune up and injectors. I have mine tuned to around 35-40 HP for the forklift.
I noticed you set the governor gap when the engine was not running. Can you set the gap on a limiting speed governor the same way? The service manual states to hold the rpms between 800-1000 while setting the gap but it’s very challenging and I’m hesitant to attempt to adjust it.
@detroitgarage9430
2 жыл бұрын
On a LS governor you set the gap with the engine running. There is a tool that was made to set the gap while engine was not running. I use the static tool mostly as the results are the same as doing it with the engine running.:) I'll check today and see what the static gap is.:)
@doorcountybywater
2 жыл бұрын
@@detroitgarage9430 thanks! We have a commercial boat powered with 4-53’s and I believe we need to adjust the governor on one of the engines because the rpms bog down under idle load. From my research it sounds like a gap adjustment but I’m nervous to attempt it.
@detroitgarage9430
2 жыл бұрын
@@doorcountybywater Yes, that sounds like the symptoms. It's not such a big deal to set the gap, you just have to mind the engine rpm.:) I would recommend a full tune up before you set the gap.
SAE40?
@detroitgarage9430
Жыл бұрын
Yes Shell Rotella T1 SAE 40.:)