Very cool! Great job!

Thank you for the video. You are awesome. I agree with you about having the rpm readout lagging is no good

I need one! That I need some wizard to hook up my Integra engine sensors to it here in Holland😎.

A very nice job! Did you get rid of lag between the real car speed and RealDash gauges

@winreboot

3 жыл бұрын

Yes, it's real time now. It's only delayed when the source is from bluetooth obd2 port, the issue is the ECU can't send the data fast enough, even if one would have the fastest/newest obd2 port reader. Dashbox module taps in to RPM signal on the gauge cluster and sends it real time (115200 baud rate)

Imagine someone connecting to your ECU and setting boost to 30psi and target 20AFR while waiting for a traffic light and he says: HEY MATE LET'S SEE HOW IT PULLS!

You're awesome! Thank you!! I got a question. My Turn signals rest on 12+ and trigger with ground. I can use a relay to switch but wanted to ask you if this unit takes both + and - signals? Should I use the analog pull up inputs?

@winreboot

3 жыл бұрын

Thanks! turn signals for my car activate with 12+ but my seat belt, door ajar, high beam etc.. activate with 12- It's been a while when I set this up and don't want to mislead you, ping them on FB, they are quick to respond. facebook.com/sp.leinonen.9 I know I used a relay to change the polarity on something but can't recall what it was now.

@betchipsandskill

3 жыл бұрын

@@winreboot Yup I know this Most Japanese vehicles use negative trigger for lights etc. I installed many aftermarket alarms so I know. It's not a big deal to change the polarity I just wanted to ask. I ordered the Dashbox and its on the way. I went ahead and wired my vehicle ahead of time. Thanks so much for your reply buddy. I would love to show you my custom dash once all is done. Cheers!

@winreboot

3 жыл бұрын

@@betchipsandskill awesome, yea when you get your dash setup running I would l like to see it for sure. There is a lot of customization possible and it looks so modern.

very good Is it possible to connect two devices to the tablet at the same time via Bluetooth? I mean OBD II and Dashbox? also when I use the ELM 327 Bluetooth I have a lag for the engine speed, where is the problem? Should I use the USB type? Will the log be removed?

@winreboot

3 жыл бұрын

Yes, you can have two devices connected. I have my obd2 elm device and dashbox. This allows more inputs displayed. Correct ELM or any obd port device has a delay, the ECU can't send pid data fast enough. Only solution is to use dashbox for that input instead.

@VasiliKali

2 жыл бұрын

how about connecting more dash boxes?

Does the connection still drops from time to time just as with (only) an obd plug? Because I only have the obdlink mx+ and I have a connection loss several times when it is in use.

@winreboot

3 жыл бұрын

I know the obd2 is always flaky and on a good day it's just slow but I have not notice it drops recently. Maybe because I'm relying on dashbox more and reading slow inputs like coolant, air temp intake form obd2, so I don't notice it.

@deanm5305

3 жыл бұрын

@@winreboot Thank you for your reply, bro. I appreciate it👍

@deanm5305

3 жыл бұрын

@@winreboot I will try it with an obd2 5.0 plug and see what it does with the stability of the connection.

hi i own a mini r56 jcw. im not able to use low beam high beam turn light left turn light right door open for example. im using OBDlink+ do i need realdash?

@winreboot

3 жыл бұрын

Realdash will not support those unless you have a dashbox to wire in the signal to it. So for example, you would tap in a wire to low beam, then run that wire to dashbox, dashbox will send the signal over bluetooth to realdash so it will be displayed in the app display. You can visit realdash forum on their website for support

@hkr4life

3 жыл бұрын

@@winreboot can we talk on whatsapp because its hard to understand for mr. so by OBD2 realdash cannot show me engine check light, engine oil pressure light, odometer too?

Bro is it possible to install dashbox to bmw e60 m5 2007

@winreboot

3 жыл бұрын

It should work as it's independent. The best would be contact the guys at www.spleinonen.com/ or message them on facebook, they are fast to respond

Does it have fuel level indicator?

@winreboot

3 жыл бұрын

Yes. You can configure it two different ways. Either wire in the fuel sender unit to dashbox and have live read out or use Realdash app to calculate the fuel tank level.

Can you help advise on how I use dashbox to get RPM ?

@winreboot

2 жыл бұрын

dashbox will come with wiring diagram, you would take the rpm wire and connect to your car's rpm. Then in RealDash configure how many pulser per rotation. There is not many to choose so you can pick and choose to make sure the rpm readout is accurate.

What brand is the display?

@winreboot

3 жыл бұрын

For the display I'm using Samsung galaxy tablet 8"

Hey bro please help me, i have installed the box and got the signals but my fuel is analog signals and its only reading 1 bar i have maxed the tank but its still reading fuel level is critically low, how did you do your fuel level? Please help me

@winreboot

3 жыл бұрын

You will need to change the fuel reading from "body electronics" to calculated vol. First select edit for fuel gauge then for "input & Values" select data source from "calculated values" -->Fuel Level (calculated) Once you do that the fuel gauge will not try to read from obd2 but will calculate based on driving etc.. When you fill up the tank make sure you click on the little gear icon in right lower, then click on add fuel. This will top off the fuel gauge to full. Hope this helps. You can also post on realdash forum, they are very helpful with everything.

@NoorFilms786

3 жыл бұрын

Thank for the quick reply friend, i have hooked up the dashbox with analog input 5 being the fuel level sensor, but it only shows me fuel being critically low, is there no way to make it work with dashbox?

@winreboot

3 жыл бұрын

@@NoorFilms786 Got it, in that case it sounds like you just need to calibrate the table. Edit the fuel gauge, select inputs, then dashbox, then analog input 5. Then edit and you will see what is the current read out from the sensor. You will see a table, since you have full tank it should be reading high about 5v. Once you ok to that it should display the fuel level. That is as much as I know, if it still gives you troubles, ping the guys at SP Leinonen of FB. They respond quick on messenger. facebook.com/sp.leinonen.9

@NoorFilms786

3 жыл бұрын

@@winreboot i will try that, thanks alot friend

hi. where can I buy the dashbox?

@winreboot

3 жыл бұрын

Here is where I got my from shop.protoparts.fi/product/630/sp-leinonen-dashbox?fbclid=IwAR0yfY9nb2yzNYSRYyTzCAdedhm8sgYVE9f3JP4owx_OEwDm3Mitsi68Pgk

Where I can get a dash box.

@winreboot

2 жыл бұрын

I got my from here shop.protoparts.fi/product/630/sp-leinonen-dashbox?fbclid=IwAR0yfY9nb2yzNYSRYyTzCAdedhm8sgYVE9f3JP4owx_OEwDm3Mitsi68Pgk

diagram?

Where do I get the dashbox

@winreboot

2 жыл бұрын

Here is link where I got my shop.protoparts.fi/product/630/sp-leinonen-dashbox?fbclid=IwAR0yfY9nb2yzNYSRYyTzCAdedhm8sgYVE9f3JP4owx_OEwDm3Mitsi68Pgk

Is this possible with obd1?

@winreboot

3 жыл бұрын

Yes, you don't need obd1 port, it it's helpfull to have as you will have more inputs. Dashbox module connects directly to the inputs, for example RPM, coolant or blinkers and then sends the signal over bluetooth to tablet. With obd port it is easier as you don't need to cut in to wires for inputs.

@fcrahimi

3 жыл бұрын

@@winreboot oh ok thank you! so where do i buy one? lol also how do i find which input gives me what from my inputs?

@winreboot

3 жыл бұрын

@@fcrahimi Here is where I got my shop.protoparts.fi/product/630/sp-leinonen-dashbox?fbclid=IwAR0yfY9nb2yzNYSRYyTzCAdedhm8sgYVE9f3JP4owx_OEwDm3Mitsi68Pgk you can contact them on FB they have great support facebook.com/sp.leinonen.9

Hey man, Have a quick question if you dont mind: I'm doing an engine swap into an older vehicle and as such I dont have any fuel level info over obd2. I see with this dashbox it is possible to give Realdash a fuel level reading which is great. Question is, can the Realdash still give me some kind of fuel economy readings? (Either instant/average Miles per gallon, or miles remaining to empty). Thank you for any input. I would love to have an indication of my fuel economy since part of my reasoning for the engine swap is to get better fuel milage than the original old engine. 😊

@winreboot

2 жыл бұрын

You can do this few different ways but I would get a aftermarket fuel lever to read it accurately or use the existing fuel level and read resistance on it. The resistance can be put in a table so you will have accurate readout. Dashbox can wire to your fuel level. This is little more harder way but gives you OEM type of precision. You can check the realdash forums on realdash.net or contact the dashbox guys, they are awesome with their support. Of course you can go with just estimates to give you fuel level and consumption. You will need gears rations, tire size, car wind drag at list ball park, fuel tank capacity etc.. RealDash will calculate all the vol and display estimates. Each time you fill up gas you would reset fuel gauge or enter how many gallons of fuel you added. It will be close but not 100% accurate, I bet after a while you will get a sense how accurate this can be and vol can be adjusted to fine tune this way.