greta video, lots of hard work, don't know why there are so many dislikes and smartass comments. I think you did a bang up job

@SparkysGarage

2 жыл бұрын

Thanks man. I’m not sure why there’s so many dislikes either. A lot of complaints about the music it seems. But silent time lapses are pretty boring.

@hyzercreek

Жыл бұрын

@@SparkysGarage Maybe if you put Justin Bieber....

Super job tackling this massive stump. Stihl MS661 chain saw is a beast. Woodland Mill 24 is very impressive. Thanks for the great vid.

@SparkysGarage

Жыл бұрын

Wish more people shared your opinion! A lot of know-it-alls out there trying to tell me everything I did wrong. Cheers!

Hey fellow grinder. I do what you do, cut them low first as I have a small machine. Helps a lot. One thing I do on ones this size is pie them up from the top down first. One that size probably in more than just four pieces in my case, as I don't have anything but me a wheel barrel and a hand truck to haul the pieces off with. I believe it does help me cut the top off too, that's why I make mention of it.

Cutting a stump that size is a PITA. I cut and ground one about that size a couple of days ago. I used a 18" chainsaw and then rented a Toro STX-26 grinder. It took me 5 hours to cut the stump and another 5 hours to grind it. It was a Maple tree so the wood was pretty hard and it had an extensive root system. I wound up making a ton of plunge cuts with the saw and did some 45 degree side cuts the same as you. I was very jealous of your chainsaw and grinder:) I had a lot of trouble making my cuts match up and probably cut 3 times more than I would have to if my cuts had all matched up. If I had owned my own STX-26, (which swings side to side as opposed to yours), I would use the stump grinder around the base of the stump first and bite into the base as far as possible to begin with. That would have reduced the diameter of my stump quite a bit and made the chainsaw work much easier. But since the grinder was a rental I didn't want to spent that much time on the grinding. Great job!

@SparkysGarage

Жыл бұрын

This one was definitely a challenge and the biggest stump id done up until this vid. Im on my 3rd set of teeth with my grinder now. Hundreds of stumps

Good job. I cut down two large maple stumps last week that were grown into a woven wire fence. Plus had bricks and glass inclusion. If you run across those run away.

I love watching stump removal

Wish you were in California, I'd pay you to come do the tree in my front yard! Lol. Good work!

That is one tough stump! Good job!

@SparkysGarage

2 жыл бұрын

Yes it was! Thanks!

Now I know what to expect next week ( hopefully) on getting a huge pear tree stump out. Professional tree co. took out the massive tree last week but will come back and remove all the roots all over my yard and grind down the stump. The tree was over 80 years old.

@SparkysGarage

3 жыл бұрын

Hoping it all goes smooth! Thanks for watching!

@Diana-gn8rp

3 жыл бұрын

*UPDATE*. Trunk is now gone and all of the roots that took over the yard. Some of the roots were 12” round and 6’ long. I could have watched them work all day long. The grinder left ruts in a few places but they planted grass seed and threw down hay over top.

@aasstock8465

2 жыл бұрын

hello

Where I live in Europe, they use a back hoe to cut a trench around the stump, taking in the roots. Then they pull it out and leave it beside the hole for a couple of weeks to let all the bugs and insects come out of the wood and crooks and crannies and go back into the hole, etc. The trunk can then be hauled off and used as wood for a number of projects.

@SparkysGarage

3 жыл бұрын

That is an option too, however if the stump is near something that is structural, or large enough to where it would cost a lot in dirt to fill in the hole, then its just easier and safer to grind the stump. Thanks for the comment!

2 tips to help your saw last: 1) Don't rev it hard without load eg @1:30 - it's OK to spin the chain at low speed near the stump and check bar lube is spraying off, but not rev full tilt with no load - bad for the engine. 2) Keep your bar and chain out of the dirt where you can eg @5:30 and @5:40 as the less dirt you get onto your chain and into the cuts the longer it'll stay sharp. I'm not sure what chain you were using but semi-chisel instead of full chisel is good for stump work as it stays sharper longer and can handle dirt / nicks better than full chisel.

@SparkysGarage

3 жыл бұрын

To each there own. Thanks for the tips! This chain was garbage anyways and it saves me a ton of time and money to ruin a chain than it does to do an additional 20-30 passes with the grinder.

@Asking-for-a-friend

3 жыл бұрын

I was also curious why you did it, but also thinking as someone who does stumps, I'd rather change a chain than spend an extra 45 minutes messing with all the extra stump left. What size saw is that anyway?

@SparkysGarage

3 жыл бұрын

@@Asking-for-a-friend STIHL MS661 with a 36" bar

@AuMechanic

2 жыл бұрын

Well.... the root of the problem was that he got greedy and cut low at the root flare where the wood grain is all caddywompus....it happens. The saw is always going to wander off cutting at the flare and as it dips it often ends up with the bar in the dirty end and the chain turns blunt fast. Better to cut a little higher through the straight grain of trunk, the saw will cut straight, and then grind from there.

@SparkysGarage

2 жыл бұрын

@@AuMechanic unfortunately due to the angle of the dirt around this stump and how tall the stump was I didn’t have an option but to cut it that low with the saw. The 3 point grinder only lifts so high.

Super nice equipment (I'm jealous).

@SparkysGarage

2 жыл бұрын

Years of hard work were traded for it. 💪🏻👌🏻

I'm shocked that Woodland Mills doesn't have a grinder to match up yet against the Baumalight 3P24. I'm stuck between one of the ones like you have, or the 3P24.

@SparkysGarage

3 жыл бұрын

This one works great!

It would have been nice to hear the machine..I'm glad i fast forward the vid

@SparkysGarage

Жыл бұрын

I have plenty of vids where you can hear the machine.

That was a monster stump.

@SparkysGarage

3 жыл бұрын

It was. That root ball just kept growing bigger the more I ground it too!

@TheManhu01

3 жыл бұрын

@@SparkysGarage , I just had the exact same problem with a pine stump that was connected to an oak stump kind of grew together. The more I ground on it with the stump grinder the larger it got. I have the backhoe attachment for my tractor. I just got frustrated and dug the damn thing out took 3 hours.

@SparkysGarage

3 жыл бұрын

@@TheManhu01 I finally got a mini ex, just put up a vid of it. So on some projects I’ll be able to dig out the stump instead. 👍🏻

@pietropasqua4523

3 жыл бұрын

@@SparkysGarage k ho Ci .

Thank you for the informative film and a lot of useful techniques shown on how to cut the tree stump as much as possible to the ground level. My concern is that even if you grind the stump and level well the stump might start start to regrow. We need to remove one tree, which grows between 2 houses (they are at a distance ~ 3 yards), so there is no place for excavator machine there. I would burn it in a slow manner, but there is AC unit sitting next to it. So it looks like to grind that stump to the surface level would be the best option, but I'm afraid it will start to grow back again or if it is a big tree it won't? I would appreciate any opinion on this matter.

@SparkysGarage

2 жыл бұрын

I’ve ground hundreds of stumps and none of them have ever grown back. Usually going 6-4” below surface level and getting all of the surface roots is sufficient to kill the tree.

@olenaerhardt7725

2 жыл бұрын

@@SparkysGarage Thank you so much for your replay, especially for that advice about desirable depth of the grinding, I thought it should be just leveled to the ground, as shown in some films. The way you say and actually it is done in your film (when the grinder goes below the surface, I even didn't notice before) is much reliable of course. I also plan to drill some holes in the remaining stump to fill them w/table salt and vinegar (don't know if it give much effect on large stumps (ours will be ~ 24" in diameter). Thank you again!

Nice job ! I was impressed...and I don't impress easily... pc

@SparkysGarage

2 жыл бұрын

Thanks man! I'm not sure why I get so much negative feedback on this vid. Just sharing the job I did

Is that a water maple stump? Very good technique but a little dulling for chain, ah well, that is what a file was made for.

@SparkysGarage

3 жыл бұрын

I’m not sure what kinds of tree it was. The guy that was contracted to grind the stump never showed. So I got called to do it. I did file the chain about half way but it was some hard wood. That’s for sure.

@eventsotherthingswithchris9019

3 жыл бұрын

@@SparkysGarage Somehow,you should reach out to some of the KZread Bushcrafters if it was hard or "fatwood"! Granted a lot of them cut down whatever to turn it into a shelter & enough for a fire, but folks like we'll say Steve Wallis end up having to either buy wood or, if someplace allows it ( most won't because of possible "contamination") maybe bring stuff they cut up @ their own homes before going out. ( Potential $??) I know I like wood burning but wow, that thing was WAY HUGE & I'm only used to doing smaller artwork if I do wood burning, so, that stump even if it was close to perfectly round @ the end would've been too much for me, let alone my wood burning irons & stuff!! Lol.

🌳 wow

Any recommendations for sharpening the teeth on that grinder?

@SparkysGarage

3 жыл бұрын

I haven’t had to sharpen them yet but they are carbide. Maybe find a carbide sharpening disk?

@martinw4261

3 жыл бұрын

@@SparkysGarage i was considering the options, maybe a diamond wheel on a bench grinder, maybe with the grit on the circumference or better on the flat lapping side? Maybe even touch up the teeth with a diamond wheel on an angle grinder. When you sharpen yours will you make a video?

@JustinGH595

3 жыл бұрын

@@martinw4261 You'll need a "green wheel" on a bench grinder. I think they're actually called a silicon carbide grinding wheel. I'd suggest at least a 6" bench grinder with some power otherwise it takes forever. Wear a mask the dust is awful and you don't want to breathe it in. Buy enough teeth so you have at least 20 sharp spares if you plan on grinding all day with no way to sharpen.

@SparkysGarage

6 ай бұрын

I just run them until they break and then replace them. It runs about 15$ a tooth after shipping. Sharpening them wouldn't be worth it.

Nicely done.. how much did you charge for a hogma like that?

@SparkysGarage

2 жыл бұрын

$600. Thank you

This style of grinder only works with a tractor that has a hydrostatic transmission not a gear to gear type

@SparkysGarage

2 жыл бұрын

Correct for the most part. It’s extremely hard to drive a gear tractor slow enough for the grinder to work properly.

I use a metal detector on my stumps before I grind. It detects metal.

@SparkysGarage

3 жыл бұрын

Good call, might have to get one one day.

@eventsotherthingswithchris9019

3 жыл бұрын

@@SparkysGarage Hi, this ended up on a "check this out" type of KZread thing. I don't know if after you put this together, if you noticed that some of your chainsaw"s "tonality" matched some of the music included? A friend of mine has something smaller in their front yard but the bottom 1/2 is almost the same size. I was joking around about ways to get rid of it & then some more serious, concern issues where eventually, they were thinking of extending their driveway to where that stump is & then, meeting the road out in front. I'm too scared of chainsaws to operate one unless it's one of those small "Ryobi" things so, I'm not touching it!!

Use a hard nose bar Sparky!

@SparkysGarage

Жыл бұрын

One day!

@ocsplc

Жыл бұрын

@@SparkysGarage I bought a reasonably cheap 36” Holzfforma hard nose and it’s great. Takes a beating and holds up

I would drill holes all around the stump then use fire to burn it away

@SparkysGarage

2 жыл бұрын

That’s not allowed in the city.

This is the way to do the job of stump removal. Cut as much wood off as you can with your chainsaw as new saws an bars an chains are cheaper then stump grinders an tractors . Big stumps are more romantic for infomercials I understand but why ware out your most expensive equipment ?

@SparkysGarage

2 жыл бұрын

I bought the equipment to wear it out.

Why are you holding the saw backwards?

@SparkysGarage

3 жыл бұрын

The same reason I write backwards, throw a ball backwards, and swing an axe backwards. I’m a lefty. 👍🏻

@eventsotherthingswithchris9019

3 жыл бұрын

@@SparkysGarage Well,if you wrote backwards, wouldn't it look sort of like this??-> "sdrawkcab gnitirw m'I !em ta, kool ! yeH" Ok, sorry, trying to share silly humor.

@matteckert6676

3 жыл бұрын

As a fellow lefty i know the struggle lol. Nice job

@SparkysGarage

2 жыл бұрын

lol

@tommak6516

2 жыл бұрын

@@eventsotherthingswithchris9019 That is clever and funny, too bad most people will not 'get it.'

Dude I always trash so many chains going through stumps. Hate it

@SparkysGarage

2 жыл бұрын

I usually save my bad chains for hard jobs like that.

You’re lucky there was no old metal grown in the stump

@SparkysGarage

2 ай бұрын

There was an old fence post I hit and didn't realize right away. That is why I had to stop and sharpen the saw.

👍👍👍🤝🤝

Baumfrevel..., mehr fällt mir hier nicht ein.

que precio tiene la demoledora de tacón...

@SparkysGarage

6 ай бұрын

$2500 usd

So 'nen richtigen "Plan" kann man bei dem Herrn nicht erkennen, weder beim Gebrauch der Kettensäge noch beim Einsatz seiner landwirtschaftlichen Maschine. Gut auch, unter der auslaufenden Sägekette das Sägemehl mit der nackten Hand wegzuwischen ... Fazit: NICHT NACHMACHEN!

@SparkysGarage

6 ай бұрын

Sorry, can you try in English?

Can use an axe to split the wood in less than a minute.

@SparkysGarage

3 жыл бұрын

You're welcome to come try!

@thomasneill7955

2 жыл бұрын

No way. I've tried it. Lol.

Stump grinder footage was cool. Music was totally inappropriate and made me not want to finish the video or subscribe to your channel. Many youtubers mistakenly think that adding music enhances their videos, but the truth is most viewers do not share your musical tastes and are not here to listen to music. Narrate the video and leave off that stuff.

@SparkysGarage

2 жыл бұрын

You’re welcome to mute the video, go to another channel, or make your own vids! Have a nice day!

@steve-ey3rx

2 жыл бұрын

@@SparkysGarage Depends on who you're making the video for, of course. Kinda like making a speech in front of a mirror if you only want to view it yourself. ;)

Sägehose.????

@SparkysGarage

3 жыл бұрын

Usually I only wear them when im doing several hours of cutting. Not on the small jobs.

Waste energy! I would use the machine claws to dig up the trunk.

@SparkysGarage

3 жыл бұрын

Not a chance, the break out force of that tractor is nowhere near what would be required to pull that stump loose.

Pessimo

Sharpen your chain for goodness sakes my man.

@SparkysGarage

5 ай бұрын

This was a garbage chain that wasn’t worth sharpening. This tree grew into a fence and would instantly dull. It was replaced after this stump. Thanks for watching