Tim shows me how to use a laser cutter to make clean cuts from an Adobe Illustrator file in acrylic (plexiglass). This video was taken at the James Madison University's X-Labs.
Жүктеу.....
Пікірлер: 48
@haworthluke4 жыл бұрын
Little tips like that dish soap one are absolutely priceless
@BarryBernau4 жыл бұрын
Great tip with the dish soap.
@M6Individual5 жыл бұрын
The voice of the cameraman seems to be Mike Mackenzie of C.E.M. There were 2 useful takeaways for me in this video: 1) Use full power to cut fast enough to not heat the rest of the material (which causes deformation/ridging) and 2) applying dishwashing soap to both sides and letting it dry before lasering. I will try "clearcoat" sheeting (which isn't clear BTW) instead as this also provided a barrier and avoids the evenness and drying issues of soap.
@ramakrishnamishra81795 жыл бұрын
Tim is awesome
@pcstixp60342 жыл бұрын
thanks! very useful!! I'll try
@elmerfudd8355 жыл бұрын
What are the specs for laser?
@jamiekhari6651 Жыл бұрын
What thickness acrylic should you buy to make windows for an architectural model? Does any acrylic work?
@GeraldCrochet5 жыл бұрын
What wattage laser is this? And presuming CO2?
@maevelyncaampued54183 жыл бұрын
What type of machine is this and where to buy
@estradababy24028 ай бұрын
Very helpful
@Sriraisender Жыл бұрын
Can we cut rubber slipper sheets like this? Faster
@syedsulaiman83803 жыл бұрын
What is the name of the laser a d can we buy the laser module separately
@cski685 жыл бұрын
Great video, I was wondering if you could help me with a few questions. My intentions are to create what looks like a cut in Acrylic but is more closer to just an internal scar that is foggy and glows like a ribbon in the Acrylic when lit. Can this be accomplished with less power and faster speeds? If this is not possible how thin can the laser cut be so it is almost invisible when viewed from the cut direction yet will glow when light is shown in the Acrylic. Thanks
@MorganBenton
5 жыл бұрын
Great question! I have no idea what the answer is, but I'm super curious to find out.
@cski68
5 жыл бұрын
@@MorganBenton Thanks for the reply, I've been looking into it for about a week still no answers. Do you have any ideas on who to ask?
@seeigecannon
5 жыл бұрын
There are 2 kinds of acrylic; cast and extruded. Cast acrylic engraves white while extruded engraves clear. You can raster the acrylic for the image, and use cast or extruded for the visual effect.
@davepeck46373 жыл бұрын
Hello. Was there an assist gas being utilized? Or shop air?
@MorganBenton
3 жыл бұрын
No, but there is an exhaust fan that vents the fumes to the outside
@Kelly-lo6cz3 жыл бұрын
Where can I buy a laser cutter? Does a small one exist? I am just wanting one to make small pieces of jewelry with acrylic and I don't know where to begin. Thanks
@MorganBenton
3 жыл бұрын
glowforge.com/our-products
@patrickalvarado76873 жыл бұрын
Not sure if I missed it in the video, but how thick is the material you're cutting?
@MorganBenton
3 жыл бұрын
It's been awhile but I think it's 1/8" in (3.175 mm)
@patrickalvarado7687
3 жыл бұрын
@@MorganBenton thanks a lot! I’m surprised you answered so quickly
@MorganBenton
3 жыл бұрын
Haha, I get notified whenever anyone comments 😄
@ascaniofiori65286 жыл бұрын
Hi, thanks for the video. Which kind of laser is ? Diode ? CO2 ? thanks a lot.
@MorganBenton
6 жыл бұрын
90W CO2
@ascaniofiori6528
6 жыл бұрын
Morgan Benton thanks !
@ndbiet4 жыл бұрын
What a fine mustache you got there
@zerosugarmatcha73485 жыл бұрын
3:08 there is a piece of peanut or something at the upper left corner, I'm wondering someone dropped it or a mouse brought it there.
@irmods
5 жыл бұрын
lol, it's actually a lump of white grease.
@leerichardscountry3 жыл бұрын
That's a right tash.
@noisefekt4 жыл бұрын
Why there’s a macaroni and some melted cheese inside the machine? :D
@KayRoepke
3 жыл бұрын
"This video was taken at the James Madison University's X-Labs." :D
@kgleatherworks1497
3 жыл бұрын
Pu
@3rdsty4 жыл бұрын
is this co2 or fiber laser?
@jessicaliu7424
3 жыл бұрын
CO2
@patrickalvarado7687
3 жыл бұрын
90W CO2 laser
@jessicaliu7424
3 жыл бұрын
@@patrickalvarado7687 Hello, dear friend, if you are interested in CO2 laser machine, please add my Whatsapp:+86-13156182531 I will give you the machine details and a quote
@macciebuilds5 жыл бұрын
didn't he use coreldraw?
@MorganBenton
5 жыл бұрын
Yes, that's the software on the computer attached to the laser cutter. However, I drew the designs on Illustrator at home before bringing them to the lab.
@macciebuilds
5 жыл бұрын
@@MorganBenton I see thank you so much for answering. :)
@jamesking4253 жыл бұрын
Hey I was wondering could I get you to do a little project for out of acrylic
@alexdorand5 жыл бұрын
you have food in the machine
@irmods
5 жыл бұрын
french fries lol
@waldner626 жыл бұрын
Thanks for the video, but what is the secret at the end, you speak to fast for me, I'm german.
@MorganBenton
6 жыл бұрын
waldner62 The "secret" mentioned is to cover the acrylic in dish soap before you cut it to prevent it from getting cloudy. You can then wash it after you're done.
@waldner62
6 жыл бұрын
Thank you very much for the fast information, I will try it.
Пікірлер: 48
Little tips like that dish soap one are absolutely priceless
Great tip with the dish soap.
The voice of the cameraman seems to be Mike Mackenzie of C.E.M. There were 2 useful takeaways for me in this video: 1) Use full power to cut fast enough to not heat the rest of the material (which causes deformation/ridging) and 2) applying dishwashing soap to both sides and letting it dry before lasering. I will try "clearcoat" sheeting (which isn't clear BTW) instead as this also provided a barrier and avoids the evenness and drying issues of soap.
Tim is awesome
thanks! very useful!! I'll try
What are the specs for laser?
What thickness acrylic should you buy to make windows for an architectural model? Does any acrylic work?
What wattage laser is this? And presuming CO2?
What type of machine is this and where to buy
Very helpful
Can we cut rubber slipper sheets like this? Faster
What is the name of the laser a d can we buy the laser module separately
Great video, I was wondering if you could help me with a few questions. My intentions are to create what looks like a cut in Acrylic but is more closer to just an internal scar that is foggy and glows like a ribbon in the Acrylic when lit. Can this be accomplished with less power and faster speeds? If this is not possible how thin can the laser cut be so it is almost invisible when viewed from the cut direction yet will glow when light is shown in the Acrylic. Thanks
@MorganBenton
5 жыл бұрын
Great question! I have no idea what the answer is, but I'm super curious to find out.
@cski68
5 жыл бұрын
@@MorganBenton Thanks for the reply, I've been looking into it for about a week still no answers. Do you have any ideas on who to ask?
@seeigecannon
5 жыл бұрын
There are 2 kinds of acrylic; cast and extruded. Cast acrylic engraves white while extruded engraves clear. You can raster the acrylic for the image, and use cast or extruded for the visual effect.
Hello. Was there an assist gas being utilized? Or shop air?
@MorganBenton
3 жыл бұрын
No, but there is an exhaust fan that vents the fumes to the outside
Where can I buy a laser cutter? Does a small one exist? I am just wanting one to make small pieces of jewelry with acrylic and I don't know where to begin. Thanks
@MorganBenton
3 жыл бұрын
glowforge.com/our-products
Not sure if I missed it in the video, but how thick is the material you're cutting?
@MorganBenton
3 жыл бұрын
It's been awhile but I think it's 1/8" in (3.175 mm)
@patrickalvarado7687
3 жыл бұрын
@@MorganBenton thanks a lot! I’m surprised you answered so quickly
@MorganBenton
3 жыл бұрын
Haha, I get notified whenever anyone comments 😄
Hi, thanks for the video. Which kind of laser is ? Diode ? CO2 ? thanks a lot.
@MorganBenton
6 жыл бұрын
90W CO2
@ascaniofiori6528
6 жыл бұрын
Morgan Benton thanks !
What a fine mustache you got there
3:08 there is a piece of peanut or something at the upper left corner, I'm wondering someone dropped it or a mouse brought it there.
@irmods
5 жыл бұрын
lol, it's actually a lump of white grease.
That's a right tash.
Why there’s a macaroni and some melted cheese inside the machine? :D
@KayRoepke
3 жыл бұрын
"This video was taken at the James Madison University's X-Labs." :D
@kgleatherworks1497
3 жыл бұрын
Pu
is this co2 or fiber laser?
@jessicaliu7424
3 жыл бұрын
CO2
@patrickalvarado7687
3 жыл бұрын
90W CO2 laser
@jessicaliu7424
3 жыл бұрын
@@patrickalvarado7687 Hello, dear friend, if you are interested in CO2 laser machine, please add my Whatsapp:+86-13156182531 I will give you the machine details and a quote
didn't he use coreldraw?
@MorganBenton
5 жыл бұрын
Yes, that's the software on the computer attached to the laser cutter. However, I drew the designs on Illustrator at home before bringing them to the lab.
@macciebuilds
5 жыл бұрын
@@MorganBenton I see thank you so much for answering. :)
Hey I was wondering could I get you to do a little project for out of acrylic
you have food in the machine
@irmods
5 жыл бұрын
french fries lol
Thanks for the video, but what is the secret at the end, you speak to fast for me, I'm german.
@MorganBenton
6 жыл бұрын
waldner62 The "secret" mentioned is to cover the acrylic in dish soap before you cut it to prevent it from getting cloudy. You can then wash it after you're done.
@waldner62
6 жыл бұрын
Thank you very much for the fast information, I will try it.
viva la dirt league?