Nice!

EXCELLENT THANKS! 🇺🇸🇺🇸

Very smart trailer, inside and out.

looks great I really like the slide out

@treyjacobson8844

6 жыл бұрын

2007crf450r dyu

One of the best RC trailers I have seen! Great Work!!! Would you mind sharing where you purchased the jack screw legs, and what they are called? I have looked all over and can't find them. Thanks in advance!

@shelbyseelbach9568

5 жыл бұрын

One year later, I'm going to say he was unwilling to provide the requested information. LOL.

Now it's the 3rd. Trailer I found here on YT. There are a lot of features I like for travelling shows. The only concerns I have is about stealing stuff or have Models stored permanent in theses Trailers. I wonder in last case if climate changes (humidity, heat or cold) would harm the material or if our damn german laws will allow driving these trailers through Germany or Europe. I mean we have LiPo's inside, Fuel and the electical stuff... If this is not installed by Profis It may cause very bad times to remember. The Idea behind these trailers I like very much. The very individual interior is impressing. Not sure if our TÜV will approve this...

RV awning on the side would be handy or a batwing "overland" 270* awning.

Nice trailer.......I really like the pullout workbench.

@treyjacobson8844

6 жыл бұрын

rctruckernut uio

Jim, it is amazing and I am, making a RC trailer for my planes,,, Thanks for the info, demonstration,, I will use many ideas from you,,,,,, Mike

Awesome!!!! Be sure to let me know when you get done with it

Very nice !

Awsome job jim i get mine next month

Hi Jim. Have been doing a lot of research, and have looked at numerous trailers here in Ohio. I wasn't impressed with the quality that you get . The pro line is my choice for the money. I ordered mine and will be making the trip to Virginia. It's worth it to me. Thanks for your help.

PERFECTO!!! 🇺🇸👍🏼🇺🇸👍🏼

An excellent customization for the R/C airplane fan. May I ask how much I should budget for a similar trailer with the rolling table and a similar interior layout?

Very nice trailer, one question how do you hold the wing panels from bouncing around? I can see the fuselage with the wheels are used to restrain the model but how do you restrain the wings from moving around. I have a smaller trailer that bounces around more that yours would and the wing panels get damaged if they are not held down.

@jimbodenheimer8451

7 жыл бұрын

Fred Cronenwett I use small bungies and hold them to the wall

mind me asking, that shore power on the side of trailer, is that cover plastic and where did you pickup please.

Hi Jim. Got my proline. Which backup system did you use? Thx

I like your trailer. How do you have your backup camera wired into the monitor in the truck?

I used 2 conductor shielded cable. Ran it to the tongue where it plugs into an RCA connector going to the monitor

can you share the store and part for the overhead led? very nice.

Hi Jim. I'm getting ready to insulate and install FRP on the ceiling. Did you do yours? I see you have what looks to be one by running across your ceiling. I was wondering if you used that to keep the frp from sagging. Thx

@jimbodenheimer8451

6 жыл бұрын

Robert Fenton I used white board with 1x3 to seam it

Awesome set up!! If you don’t mind me asking, what did you use on the roof to cover the insulation?

@jimbodenheimer8451

5 жыл бұрын

I used whiteboard panels from Lowe's. Stays clean and helps with the interior lighting

Hi Jim. Nice job. Could you please tell me where you found the screw jacks for the adjustable legs? What a cool setup. Thx

@jimbodenheimer8451

6 жыл бұрын

Robert Fenton I made them from conduit. Milled a slot in it, welded a nut in one end and used threaded rod

@gitup73

6 жыл бұрын

Jim Bodenheimer Thx Jim. I thought so. It looked like you fabricated it. Thanks for sharing your ideas.

There is a lot of room on a trailers ceiling and I am designing a way to hang all my wings across the top so that I don't waste wall space like you did. Wall space is to hang planes.

@jimbodenheimer8451

3 жыл бұрын

Great idea. Not really wasted space, just different. Share it when you are done!!!

@kenpappas9520

3 жыл бұрын

@@jimbodenheimer8451 Will do!

Hi Jim. If you wouldn't mind, where did you find the warehouse shelving that you used? Thx

@jimbodenheimer8451

6 жыл бұрын

Robert Fenton I actually got it from a warehouse that was going out of business

What did you use for the white ceiling ?

Very nice , Can u tell me how you hook up all electronics and where u get power from ?

@jimbodenheimer8451

5 жыл бұрын

Sure. I run 120 VAC in the trailer to a basic automatic battery charger, then out to the receptacles throughout the trailer. Everything else is powered off a 12VDC deep cycle battery that the charger us hooked to. This maintains the battery nicely.

I got a combo off Amazon. 45 bucks I think, had monitor and camera

where did you get the slide track for your bench

@jimbodenheimer8451

7 жыл бұрын

Tommy Miskura It's unistrut. Normally used to hang conduit and piping. Lowe's or Home Depot has it

How did you store the wings?

What runs inside the Unistrut?

@jimbodenheimer8451

7 жыл бұрын

I just used the unistrut as basically a drawyer slide. It's nested in another strut on the slide out. I also used is as a frame rail for the upper shelf.

what size is the trailer 6x12?

@jimbodenheimer8451

7 жыл бұрын

yes it's 6x12

I spent less than 500 on the interior.

CAN NOT HEAR YOU

@bicwig

3 жыл бұрын

Is there any sound? Been up for 3 years now and haven't had an issue but want to make sure you can hear it.