Correction: the internal hex (allen) at the begginning is 14mm
Жүктеу.....
Пікірлер: 29
@17ukjonnyt2 жыл бұрын
Just fitted my wheel and was unsure about the gap between the RH spacer and the axle, good to see that it was normal. Thanks very much for the video ;)
@gonzaloluna19892 жыл бұрын
It is not a 12 mm! It has to be bigger, I looked at your video and went by that. It was too SMALL
@berny1er
2 жыл бұрын
It's true, it is a 14mm
@RideyRodney
2 жыл бұрын
My CRF250L is a 14mm, I’m guessing the 300l is 14mm too.
@Toya4x4
Жыл бұрын
I measured on my CRF 300LA (MY2022) and it is 14mm. Perhaps you would like to make a comment in the film and give the correct info.
@lonniehargrave9381
Жыл бұрын
Yes, drove 30 min to get the 12mil at a shop. Got home, bummer. Got it the next day.
@mcdonaldslover522 жыл бұрын
thanks for this video - got a 300L and always prefer watching bike specific videos for this, every bike has its kink
@jean38665 Жыл бұрын
thanks, very helpful
@siscoramingo85369 ай бұрын
Hi , we need a SUPERPINION ( BEST front sprocket just like SUPERPINION ) for our CRF300L / THX for forward around
@airadaimagery6922 жыл бұрын
Subscribed! Did you do a video on the rear wheel?
@DaBinChe
2 жыл бұрын
not yet, will soon
@Mojo545 Жыл бұрын
Why would Honda go with this 14mm allen key for the front axel? Its so odd.
@DaBinChe
Жыл бұрын
internal so it doesn't get damage compared to external in a crash
@ChrisGough-kn2wj5 ай бұрын
Just measured axle allen flat to flat on my 2021 is 14MM not 12
@alexjones-qe5gc10 ай бұрын
It’s not 12mm I just went to the store and bought one
@FrozenHaxor2 ай бұрын
Your torque for the two pinch bolts is totally incorrect. It's not 6 foot-pound, it's 16. The actual spec is 22 Nm. Your spec for the axle bolt was correct, 69 Nm. You also are supposed to compress the forks a couple of times before tightening down the two pinch bolts, doing so will prevent any binding of the pistons inside the forks due to misalignment.
@alyrealty Жыл бұрын
Thank you grerat video for someone who has never done it before.
@phantomshtter
Жыл бұрын
Yeah great video, go buy a 12 mm socket when it's actually a 14.
@leeknievel7482 жыл бұрын
But why didnt you go ahead on those pinch bolts and use your torque wrench anyway?
@DaBinChe
2 жыл бұрын
I have enough experience to go by feel
@leeknievel748
2 жыл бұрын
@@DaBinChe Well, ok, so do I but i'd rather be exact lol
@DaBinChe
2 жыл бұрын
@@leeknievel748 somethings you can get away with some not. I would use a torque wrench on engine internals but most everything outside that I'm confident enough in my skills not to.
@phantomshtter
Жыл бұрын
@DaBinChe Yeah your skills are so honed you jack up a wheel before breaking the fasteners and you can't even read the correct socket size. "iT's A 12mM"🤪 You have NO BUSINESS making how to videos!
@paulo1787 Жыл бұрын
Good vid, appreciated 👍
@phantomshtter
Жыл бұрын
How the f*** is it a good video when he's literally quoting the wrong size tool?🤷🤷🤷
@justinpare6462 жыл бұрын
Do you have a rear removal video?
@DaBinChe
2 жыл бұрын
I thought I made one, but guess not. I'll make one when I need to remove it.
@phantomshtter
Жыл бұрын
@@DaBinChe You gonna tell him the wrong tool size like you didn't this video?
Пікірлер: 29
Just fitted my wheel and was unsure about the gap between the RH spacer and the axle, good to see that it was normal. Thanks very much for the video ;)
It is not a 12 mm! It has to be bigger, I looked at your video and went by that. It was too SMALL
@berny1er
2 жыл бұрын
It's true, it is a 14mm
@RideyRodney
2 жыл бұрын
My CRF250L is a 14mm, I’m guessing the 300l is 14mm too.
@Toya4x4
Жыл бұрын
I measured on my CRF 300LA (MY2022) and it is 14mm. Perhaps you would like to make a comment in the film and give the correct info.
@lonniehargrave9381
Жыл бұрын
Yes, drove 30 min to get the 12mil at a shop. Got home, bummer. Got it the next day.
thanks for this video - got a 300L and always prefer watching bike specific videos for this, every bike has its kink
thanks, very helpful
Hi , we need a SUPERPINION ( BEST front sprocket just like SUPERPINION ) for our CRF300L / THX for forward around
Subscribed! Did you do a video on the rear wheel?
@DaBinChe
2 жыл бұрын
not yet, will soon
Why would Honda go with this 14mm allen key for the front axel? Its so odd.
@DaBinChe
Жыл бұрын
internal so it doesn't get damage compared to external in a crash
Just measured axle allen flat to flat on my 2021 is 14MM not 12
It’s not 12mm I just went to the store and bought one
Your torque for the two pinch bolts is totally incorrect. It's not 6 foot-pound, it's 16. The actual spec is 22 Nm. Your spec for the axle bolt was correct, 69 Nm. You also are supposed to compress the forks a couple of times before tightening down the two pinch bolts, doing so will prevent any binding of the pistons inside the forks due to misalignment.
Thank you grerat video for someone who has never done it before.
@phantomshtter
Жыл бұрын
Yeah great video, go buy a 12 mm socket when it's actually a 14.
But why didnt you go ahead on those pinch bolts and use your torque wrench anyway?
@DaBinChe
2 жыл бұрын
I have enough experience to go by feel
@leeknievel748
2 жыл бұрын
@@DaBinChe Well, ok, so do I but i'd rather be exact lol
@DaBinChe
2 жыл бұрын
@@leeknievel748 somethings you can get away with some not. I would use a torque wrench on engine internals but most everything outside that I'm confident enough in my skills not to.
@phantomshtter
Жыл бұрын
@DaBinChe Yeah your skills are so honed you jack up a wheel before breaking the fasteners and you can't even read the correct socket size. "iT's A 12mM"🤪 You have NO BUSINESS making how to videos!
Good vid, appreciated 👍
@phantomshtter
Жыл бұрын
How the f*** is it a good video when he's literally quoting the wrong size tool?🤷🤷🤷
Do you have a rear removal video?
@DaBinChe
2 жыл бұрын
I thought I made one, but guess not. I'll make one when I need to remove it.
@phantomshtter
Жыл бұрын
@@DaBinChe You gonna tell him the wrong tool size like you didn't this video?