You saved me from buying another drill. I was looking and it cost me about 140€ back in 2010 and now it's over 200 🤦🏻‍♂️ thank you!!

@jllgarcia

Жыл бұрын

Aaaand it still doesn't work. Seems that when it colds off, stops working again. When I use the hot air gun over the board, or put the drill itself over the stove, works well. But once it's cold again, stops working. Somebody knows what's the problem? 😭

Love this drill, used every day for 12 years, batteries still in perfect condition. Just going to buy a spare one in case it ever packs up.

Great job, and video "Alex B". I bought one in 2012, with two batteries and charger, but OEM version (no box and case). Batteries are dead about 7 years ago, but I rebuilt and sold that another drill. I use this drill with newer version higher capacity batteries (4 AH & 5AH batteries). My father is destroyed its chuck, I replaced it a metal drill chuck from AliExpress, and works fine. I checked it on Bosch services online page, but it has got a high price for me (~41.1USD). As they say in Hungary, the material is still in it.

I have the same drill, and my problem was: squeezing the switch just had the power LEDs flash a few times but the chuck wouldn't rotate. I came here for the walkthrough of opening it up (good clear video - nice work on that filming) and your "Safety Mode" inspired me to try out the same trick: hairdryer on the board. All works now! Thanks for the video; I now have a fully-functioning drill (and a mental note not to keep it up in the shed anymore!)

I have the later PSB 1800 LI-2 model but I think the previous owner left it out in the rain. Just like some other comments left here , when i squeeze the trigger the light flashes on but that's all. Tried it a few times and when I opened it part of the board was black and smoked when the trigger was pulled. I bought another one for parts but it has'nt arrived yet . Thanks for the video. It was most helpful and hopefully I will be able to fix my drill.

thanks for showing the details of assembling the gears!

@AlexBRestoration

Жыл бұрын

🍺🍺

Thank you so much saved me a whole lot of money, didn't do a full service this time but now i have the info i most certainly will later on.

Fantastic video, Alex! Dropped drill and drive did not work thereafter. Stripped down and rebuilt would not have been possible without this excellent video. Only problem was after assembly settings were out by 180 degrees. Section that locks into chuck head had to be turned so had to disassemble. Would have thought it would have had different cut outs to prevent this!

Take pics as you take apart, nice video I had to figure it out the old way. At it again now as the motor went and had to fit new one. It’s my go to drill so gets a fair bit of work. Trouble is drilling above or in dusty material the dirt goes in the drill.

Thanks for the video -- it got me started on my repair. In case any anyone else misses it, there is a screw hidden at the very bottom of the drill in the track that holds on the battery...

You did it very well compared to the other channel

I just bougie a broken 18li2 just because of This video, Nice job Alex, i hope i can repair it

@AlexBRestoration

4 жыл бұрын

What happened?

@AlexBRestoration

4 жыл бұрын

I thought u broke a drill because of me🤣 sorry hope everything goes well and u can manage to fix it

@bartgrosemans9671

4 жыл бұрын

Nah, I bought a broken one and will try to repair it just the way you did, bougie is what my phone made from bought😁

@bartgrosemans9671

4 жыл бұрын

Alex, got the drill open and the electronic board has damage, the triac is blown

very good clarity video congratulations congratulations

@AlexBRestoration

3 жыл бұрын

Thanks man 🍺🍺

Thanks for the video, found it very helpful👍👍

THANK YOU! I have been searching for a video like this for a week. exactly what I needed.

@AlexBRestoration

4 жыл бұрын

I'm glad I was able to help you, and you subscribe my channel?

Very satisfying to watch thank you. I’ll try with my drill.

Wowwww! You made it new!

@AlexBRestoration

3 жыл бұрын

Thanks🍺🍺

Tip: Don't spray anything inside the motor! At first it looks okay but after a while dirt and carbon stick to the commutator and cause shorts in the windings. Better take it apart and clean the inside or buy a new one if the overall state is too bad.

@AlexBRestoration

8 ай бұрын

Thank you for advice,but the spray is contact cleaner for electrical parts

@codebeat4192

8 ай бұрын

@@AlexBRestoration But this also happen with contact cleaner, not suitable for this task if you don't clean off the cleaner afterwards.

Very good video. I have the same problem. Will try the hair dryer 😁

i love alot of your grease pump, it was small and useful

@AlexBRestoration

4 жыл бұрын

Me to🥰 worth all the money

@thecurrabelapprentice

3 жыл бұрын

What grease pump is it please?

I have used this model intensively for many years, it is still working fine, but when I release the trigger the leds stay on and drain the battery. I opened up the drill and gave the electronics some cleaning spray and dried it, but the problem persists. Changing the battery does't help.

Excellent job

Great stuff! I have a PSB 12 VSP-2 which needs restoration. Also a new trigger switch. Could you help with some instructions on dismantling the chuck and gearbox. Thanks. Sham.

@AlexBRestoration

3 жыл бұрын

Thank you for comment,you can find a lots videos with chuck removal and gearbox vsp-2 it's same like in my video.🍺🍺

hola buenas noches amigo. Una duda eso que pones en el minuto 12:47 que tomas con la pinza, que son como posteitos para que son? tengo un destornillador mas pequeño que ese marca klatter, lo desarme y en un descuido se me cayeron dos postesitos exacatamente igual, y no lo eh podido armar, queria que me apoyes para saber que son, y que funcion tienen, de igual forma los puse como en tu video pero suena como que raspa algo. Espero puedas apoyarme

Gracias maestro!!

hi alex, i enjoyed your video. i have the same problem in that i have a fully charged battery and when i pull the trigger the lights flash exactly like yours did and i think you said it went into safety mode ?how do you get it out of safety mode. i have taken it apart the same as you did but it fails at the point it started going for you. any suggestions would be appreciated. thanks again.

@alirezaharat915

2 жыл бұрын

hey, this problem is caused by moisture on the board, you must get the board dry out by hair drier and it will be ok.

Great. Can you recommend the lubricants you have used?

put a multi meter on motor and switch got continuity but put it on power lugs that fit into drill battery base ...nothing, is this a mother board fault as dropped drill thus not working

Bravo.

Valdemiro 03/2021 Excelente.

@andressergio1532

3 жыл бұрын

Instablaster

@JuanCastro-iu9xw

2 жыл бұрын

@@andressergio1532 ere un. maniya

Brill. I can use this as a guide to clean mine up. Thanks for doing this video. It's brilliant. Are there brushes that can be replaced on the motor, if so how?

@AlexBRestoration

2 жыл бұрын

Thank you for watching, check others videos for brushes replacement cuz is hard to explain.

@aaronclark8877

2 жыл бұрын

@@AlexBRestoration will do thanks

i am not good in electric things.... my problem with my cordless drill is when i turned it on it is very hot and a lot of smoke.... i dont know what to do.... any suggestion ?

@AlexBRestoration

4 жыл бұрын

Thank you for comment,You have to open the drill and check inside where is smoke,usually is smoke from carbon brushes and the overheating is from motor and gearbox .

Well done I know this line is the consumer home grade I live in the United States when bosch use to OWN skill brand that would be there DIY basic line of tools under the umbrella so probably similar specs on there are numbers we use we don't use newton meters we use torque but generally similar people it was marketed towards to these particular ones there's no way to charge the batteries here in the states without a step up transformer when it comes to the regular blue Bosch professional line as you guys market it there I can purchase any beer tool I want it will fit my batteries and work perfectly fine

Krass mega 👍 Video

Excellent tear down… If mines is squeaking and screeching but still working what do you suggest? Do I need to replace a part?

@AlexBRestoration

3 жыл бұрын

First you have to open the drill to check it because not every time something is broken inside.

what is that small grease squirter you are using around 14 minutes in?, is that a refillable tool, or something?

@AlexBRestoration

4 жыл бұрын

The name is BETA mini grease gun and yes is refillable

@Neslekkim

4 жыл бұрын

@@AlexBRestoration cool, have been looking at some better way than digging in the grease tube. (using very little of the stuff, so a full greasegun is something I want to have )

Güzel çalışma

excelente

Is it possible to change the carbon brushes yourself or do I have to buy a new motor?

@AlexBRestoration

3 жыл бұрын

I think is possible but very hard to replace it.

great job you have several empty cases

Great job Alex !

Good JOB !!!!!

very nice, thanks

Excellent vid..I have the same but later model c2017..hardly used but the chuck head has run out..not a huge amount but unnacceptable, especially noticeable when using spade end drill bits. I got a 2yr warranty from May 2017 by registering online. .. dont fancy servicing mine by any chance ? lol

@AlexBRestoration

4 жыл бұрын

With great pleasure if you live in UK🤣🤣🍺🍺

@guilbert00

4 жыл бұрын

@@AlexBRestoration ..as it happens I do live in the UK..Northants to be a little more precise lol. Of course my question was in part jest..ive just started the replacement of 8 internal doors and the furniture..hence drill for latches etc..ive since also watched horror vids of "run out" drill comparisons with kit far more expensive than mine. I also watched an excellent vid by a young lad explaining exactly where and why this occurs. Seems even fancy drills suffer from the same problem even when new. My thinking at the mo is that I cant see me risking a 24mm hole for the latch case on a 35mm door so im proposing to use a 20 or 22mm and chisel the rest out..anyway I digress. Where did you get your expertise ?..and how much ? ha ha

@AlexBRestoration

4 жыл бұрын

😅😅I live in Northern Ireland and it's free for you

@guilbert00

4 жыл бұрын

@@AlexBRestoration free eh..🤔 im not suspicious by nature but free sounds like theres a catch somewhere 🤣

Nice video. Could your help me? My drill have an issue: works but lose torque... Have 25 levels buts is like to always work on 10... Thanks

@AlexBRestoration

4 жыл бұрын

Hi.thank you for comment,you need to check the clutch and to do that you need to take down the gearbox and chuck.if there is something broke you have to replace and it is not worth it,but you have to check first🍺🍺

i have a problem with a same drill. it works only on max rpm,i can not to regulate rpm-s with a switch. and, all leds somethimes blinking,sometimes not. i have not original battery,i tried it with car battery,and with a power supply on 16,17 18 v....and simptomes allways the same. do you have idea what can it be ?

@AlexBRestoration

4 жыл бұрын

Hi.how many times the leds it's blinking,and you check the drill with a original battery,?

@brankoYT3KTT

4 жыл бұрын

@@AlexBRestoration not the same every time..mostly,it blinks very fast and dont stop,until i release the switch..... sometimes blinks just once,fast.....i did not chack it with original,i dont have. can you tell me,on original battery,are two terminals positive and two negative ? this is the way i connect it to power supply ? maybe i connected wrong ?

@AlexBRestoration

4 жыл бұрын

It's one by one the others one is for battery temperature,I think your drill is going in safety mode when you press the switch.and definitely you need a original battery 18v lithium ion.

@brankoYT3KTT

4 жыл бұрын

@@AlexBRestoration but,it works,only without rpm regulation,only at max rpm... i think,in safe mode, tool will be shut of

@brankoYT3KTT

4 жыл бұрын

@@AlexBRestoration so pinout is + - + - ? or ++- -

Peace replacement Drive Parkside pass 3.6 b2 Thank you

@AlexBRestoration

4 жыл бұрын

Sorry but I don't like parkside.🍺🍺

@chakibebrahim3548

4 жыл бұрын

there is no problem thank you

I need help from you I want number one of transor number that completely burn

@AlexBRestoration

3 жыл бұрын

Hi.you have everything here www.mtmc.co.uk/Bosch-PSB-1800-LI-2-/-3603JA3300-/-EU-18-Volt-Spare-Parts__p-162508.aspx

Hi! Do you know how to dismount the chuck?

Mantap

Yıkamak için ne kullandınız

Do uou have any suggestion, how I could see the elektronic diagram of this machine??

@AlexBRestoration

4 жыл бұрын

Hi.I have no idea where can you find the electronic diagram,check on Google

About the wires towards the switch: The brown and blue are the +,-. But what us the function of the white (thick) wire?? Rgd, Jan

@AlexBRestoration

4 жыл бұрын

Thank you for comment I have to open the drill to check where is going the white wire,or to check the electric diagram.

@JPAG0806

4 жыл бұрын

The thick white wire goes to the circuit board!

Very good job bro.. Pls tellme What type of motor it used bro?? Pls answer i would like to buy sparepart for motor to prepare if any damage later

@AlexBRestoration

4 жыл бұрын

DC MOTOR 18v 2609003662 this is the cod for motor but in my opinion is to expensive is like half price of brand new drill with batteries and charger,you can find cheap spar parts on ebay.

@mithunjs2533

3 жыл бұрын

@@AlexBRestoration thish motor Rs 550?

Why did you wash so much and remove the screws from the old case and end up putting another one? desde argentina

@FluffyFooFookins

3 жыл бұрын

probably he's reselling as a refurb.

Защо ни загуби времето с миенето на големите пластмаси, след като си решил да ползваш други?

Muito bom gostei 👍

Top!

Alex, when i test the resistance value of the motor,its zero ohm, so shortcut, can i repair the motor or just buy a new one, te bart

@AlexBRestoration

4 жыл бұрын

Hi.buy new one cuz it's hard to fix a dc motor like this one.even the carbon brushes it is difficult to replace

@bartgrosemans9671

4 жыл бұрын

Electronics where blown too so already fixed those

I have an 18 volt dc motor. It works intermittently. I gave electricity directly from the brushes again, the engine is running. one stands. what is the problem

@AlexBRestoration

4 жыл бұрын

Can you be more explicit?sometimes when the dc motor its running intermittently can be brushes,trigger swich or electronic board

@salimdeveci

4 жыл бұрын

@@AlexBRestorationhi 4.2 amps of 19 volts from the laptop adapter. My question is that if the engine is burned, it never turns, right? my engine keeps turning one round or half round.

Great work

What spray did you use for the board?

@AlexBRestoration

4 жыл бұрын

I used liqui moly contact spray

good!))

eh ben balaise nice job

Ve o sprey ne ?

Washing use what ?

@AlexBRestoration

4 жыл бұрын

I used heavy duty degreaser and for gears cleaner degreaser

Nice👍🏻

thanks!

How hapen this to screw are broken inside

@AlexBRestoration

4 жыл бұрын

Honestly, I don't know I brought the cordless drill like that,maybe from moisture, poor quality,it's often happened to me when I unscrew the screws from the batteries.

@alekpap4809

3 жыл бұрын

Very crazy.china made

what kind of grease is that ... and this pump ... where to buy it?

@AlexBRestoration

4 жыл бұрын

Hi.is BETA 1750M mini grease gun,I both from amazon and the grease is liqui moly grease for bearings.

@tomaszgalubinski5562

4 жыл бұрын

​@@AlexBRestoration thanks :D

What solution for clean gears

@AlexBRestoration

4 жыл бұрын

I cleaned with white spirit and spray clean parts but also you can use fairy,degreaser with hot water.

@alekpop1625

4 жыл бұрын

@@AlexBRestoration yes formetal gears

@alekpop1625

4 жыл бұрын

@@AlexBRestoration ok

This machine using motor No?

@AlexBRestoration

3 жыл бұрын

Yes

Nice

Türkçe ve İngilizce yazdım