Wire ferrules are extremely important! Love using them. Everyone always complains in the comments saying “why didn’t you crimp” when they don’t understand that the set screw basically crimps it for you

@gaurd3

Жыл бұрын

Hogwash. Why are they extremely important if you have all of the wire strands tucked in, and screwed down tightly attached. Half the videos on KZread is selling shit you don’t necessarily need.

@onesikm3

11 ай бұрын

He did it all wrong lol didn’t crimp the ferrule to the wire just being secured in place by the heat stink bad information

@flowshine74

10 ай бұрын

"basically"? yikes! please crimp, loose connections cause heat and eventually fire! not to mention the fastest easiest way to strip your set screw on your amp! and we know that isn't fun at all!

@logansnoddy9717

4 ай бұрын

⁠@@flowshine74the set screw does the exact same damn thing it would do if it was bare wire. BUT when the wire ferrule is used, it contains all the wires and gives the set screw a solid place to sit. The ferrule is made of very thin metal. You can squeeze it together with your fingers. Therefore, it’s not gonna strip your screw. Every single professional car audio installer used ferrules in this exact same way unless it’s smaller than 8 gauge wire. And there’s a tool that crimps the ferrule and wire into a square for smaller wire. This is the absolute best known/cleanest way to install amp wiring

@compa_choo

10 күн бұрын

​@@gaurd3if you're doing one n done then sure but alot of ppl change shit up on their build and taking wire off the amp and reinstalling will rip strands off ruining your connections, wire ferrules make sure thats no longer a problem. It's kinda an obvious purpose to them honestly

Interesting I’ve been a lineman for 6 years, I’ve never seen someone put a ferrule on without crimping it first! I understand you thinking that the screw will suffice with crimping to the wire but that is just not the case it needs to be crimped along the entire barrel before putting on heat shrink! Otherwise you will have a terrible connection or even worse that positive slips and shorts from line to ground and you need a new fuse!

Awesome. Can I use wire ferrules on amplifier input reducers?

I always crimp the wire in the ferrule with the amp screw before shrinking the wrap down to make sure the screw doesn’t pull the ferrule out of the glue

did this exact thing on my first install on my amp thank you

Thats cool but i prefer the wire reducers imo

car audio fabrication’s video on ferrules has done everybody a disservice. “set screw crimps” are useless, loose, and dangerous. don’t compromise your equipment- use ferrules as they were designed to be used and CRIMP. it’s so cheap nowadays.

Love it will be buying lol

Mine keep falling out but my wires don’t hang out my amp like that 😭 people just strip them back little much,.. and keep them twisted

Where to get the fittings at?

You should always ground your amp before adding power

Crazy i use that size for speaker wire

@deadass9493

Ай бұрын

It’s a speaker wire, your not powering a junkyard crane magnet neither

@DeeHermanson

Ай бұрын

@@deadass9493 never know.. I might just do that 😉💪👍

Were can i buy

What if i need to wire two wires to the same port ?

Its crazy how something so easy and ppl put to much thought into it thinking thy cant do it

I have a 2021 Mazda 6 with a factory Bose system. No one can seem to tell me how to get a sub and speakers in my car. I’m not a radio guy but three shops can’t get it right. What are they doing wrong. Please help

@ProvoBeastAudio

2 жыл бұрын

Send us a message on facebook and we can help!

@uhpixr

Жыл бұрын

They just need to tap the in line converter to the Bose system not just the speaker wires

@jsteezy80

Жыл бұрын

To keep my car stealth I kept the nine speaker Infinity sound system. I just used an audio control line out converter from the stock sub wires. Removed the stock sub itself and then ran RCA's from the line out converter to an amp. It's possible that the signal coming from any of your speaker wires isn't sufficient for some reason or another due to the stock DSP but it should be possible

@funnybologna6656

Жыл бұрын

Get a dsp audiocontrol dm810

@brandontrue3859

Жыл бұрын

Buy an LC2I or and LOC and T Tap into rear deck + and - left and right, run a remote from fuse box with a fuse that turns on and off with the car, set up electrical from battery

There was a lack of crimping...?

@radelement3987

Жыл бұрын

Tighten the bolt and it'll crimp it

@firebender3092

Жыл бұрын

don’t need to crimp that

@haydenpryor2494

Жыл бұрын

The screw on the amp crimps it a good bit

@260k1s

Жыл бұрын

The screw crimps it tight

@growingup4487

Жыл бұрын

they hold but they're kinda loose I'd crimp them

You gotta have pro audio money to aquire these, most of the time first timers are just trying to get the loudest for the cheapest, so all the little extra accessories aren't important

@JamesZ-py1xl

8 ай бұрын

yup I just want it to work after I hook it up lol. I'm not worried about all the details yet.

@RealMACGamer

7 ай бұрын

they like 10 dollars on amazon

@UnitedStatesofAmerica239

4 ай бұрын

I do 😕

Now what about those amps that use stupidly small insert holes for the wires? Or the ones that require the screw to be threaded through all the way?

@cjxfam5722

2 ай бұрын

Exactly what I have right now, a 5 channel Pioneer, the speaker wire inserts are ridiculously small...

Forgot to crimp Holmes lol

Wish I could do this but my screw in my amp is stripped so I can't do this

@samuelsalgado9687

10 ай бұрын

Me too😭😭

@flowshine74

10 ай бұрын

would not be surprised to find out that using the set screw on the amp to "crimp" the wire ferral is what caused yours to be stripped. I don't know what you do about that on an amp so I'm no help, sorry and good luck my friend

@kyleward7805

9 ай бұрын

Replace screw with a slightly larger diameter screw. Make sure to thread it in straight and slowly

@HighVoltageMadness

6 ай бұрын

Use a helicoil

Maybe I'm stoned af but it looks like the amps hitting ah hookah after he shrink wraps it 😂

My amp stays on when car is off and I have everything connected right. My head unit is factory so I had to use a line converter to be able to connect the RCA cables but even with the remote wire connected it stays on😢

@jamesedwards-tn6gp

9 ай бұрын

Add a switch

Unfortunately my 4 gauge wire is too thick for my amp so these ferrules don’t work for me

@illyasvielgoddenflash2340

10 ай бұрын

go find bigger wire ferrules

@ICT_Anton

6 ай бұрын

They make adapters... That's how you run 0 gauge to a 4 gauge amp input... They're fairly cheap on Amazon

But, you didn't crimp the ferrule???

@ProvoBeastAudio

Жыл бұрын

Terminal creates the perfect sized crimp.

Where can I get those wire covers

@funnybologna6656

Жыл бұрын

Called wire ferrels Amazon

You forgot to crimp the ferrule, also using a good copper infused grease like Jet lube prior to the ferrule installation helps inprove conductivety and corrosion.😏👍

@ProvoBeastAudio

9 ай бұрын

Terminal of the amp does a great crimp and crimps based on that terminal type. You shouldn't have any corrosion at the amp unless you have moisture leaks in vehicle.

You literally did nothing 😂😂🤦🏽‍♂️