the best explanation....you saved my life...thankss
@user-jh8ri9po7j8 жыл бұрын
Thanks!
@desivideshi48536 жыл бұрын
Very good.
@infmnt7 жыл бұрын
This is more about bridging than about VLANS. This setup perfectly work without VLANS also... Only with bridges.
@kukuricapica
7 жыл бұрын
+Jiří Štegl Ahoj Jirko, chtel jsme se zeptat jestli nemaz zkusenosti s Vlan v Mikrotikovi. Mam p2p spoj ve wds-bridge (2 Sextanty na 150m). Potreboval bych vytvorit 2x VLAN a potrebuji aby jedna byla tagovana a druha netagovana (pro klienty).
@sorinsuri6026 Жыл бұрын
Hello can you tell me how to configure a voice vlan?
@robdiego22057 жыл бұрын
under quick setup do you use router or bridge mode? whats the difference and does it even matter?
@ingdaka
7 жыл бұрын
This one is for bridge mode! If you will use router mode that mean you will have minimum of 2 IP subnet
@prn008 жыл бұрын
very good video and explanation!! I have a network where all the devices are connected to a single port on my routerboard (port 2), my switch is unmanaged so how can I create 2 vlans (the second is to use on unifi guest network) and make sure that all the devices I connect with ethernet go automatically on vlan 10 (and then I assign vlan 20 on guests on unifi)
@ingdaka
7 жыл бұрын
This can work too if you create vlan on unifi too. You can do this because those ate untaget vlan
@usmansaleem95694 жыл бұрын
Please make a video about Hybrid vlan
@eliasantes7 жыл бұрын
if I create VLAN30 in interface Ether1 and a want that VLAN30 be a DHCP client?
@ingdaka
7 жыл бұрын
You can do it! Just create VLAN and go to IP > DHCP Client > Add and choose as interface VLAN30
@dichvumaytinh6 жыл бұрын
i want pppoe client ISP on vlan1,vlan2,vlan3.... can you help me?
@ingdaka
6 жыл бұрын
Sure i can help. email: ilirdaka@live.com
@sajidaliofficial065 жыл бұрын
I need help can you plz
@Rafael.Almonte5 жыл бұрын
DHCP Server can not run on slave interface error! please help
@siwilson1437
4 жыл бұрын
You may have the default config set up which runs ports 2-5 as slaves, as opposed to no config. This creates bridges across the ports which you can remove in Bridge>Ports, and you should see the 'S' next to that port vanish in Interfaces, showing it is no longer a Slave port.
Пікірлер: 21
the best explanation....you saved my life...thankss
Thanks!
Very good.
This is more about bridging than about VLANS. This setup perfectly work without VLANS also... Only with bridges.
@kukuricapica
7 жыл бұрын
+Jiří Štegl Ahoj Jirko, chtel jsme se zeptat jestli nemaz zkusenosti s Vlan v Mikrotikovi. Mam p2p spoj ve wds-bridge (2 Sextanty na 150m). Potreboval bych vytvorit 2x VLAN a potrebuji aby jedna byla tagovana a druha netagovana (pro klienty).
Hello can you tell me how to configure a voice vlan?
under quick setup do you use router or bridge mode? whats the difference and does it even matter?
@ingdaka
7 жыл бұрын
This one is for bridge mode! If you will use router mode that mean you will have minimum of 2 IP subnet
very good video and explanation!! I have a network where all the devices are connected to a single port on my routerboard (port 2), my switch is unmanaged so how can I create 2 vlans (the second is to use on unifi guest network) and make sure that all the devices I connect with ethernet go automatically on vlan 10 (and then I assign vlan 20 on guests on unifi)
@ingdaka
7 жыл бұрын
This can work too if you create vlan on unifi too. You can do this because those ate untaget vlan
Please make a video about Hybrid vlan
if I create VLAN30 in interface Ether1 and a want that VLAN30 be a DHCP client?
@ingdaka
7 жыл бұрын
You can do it! Just create VLAN and go to IP > DHCP Client > Add and choose as interface VLAN30
i want pppoe client ISP on vlan1,vlan2,vlan3.... can you help me?
@ingdaka
6 жыл бұрын
Sure i can help. email: ilirdaka@live.com
I need help can you plz
DHCP Server can not run on slave interface error! please help
@siwilson1437
4 жыл бұрын
You may have the default config set up which runs ports 2-5 as slaves, as opposed to no config. This creates bridges across the ports which you can remove in Bridge>Ports, and you should see the 'S' next to that port vanish in Interfaces, showing it is no longer a Slave port.