Concrete Wedge Anchor Installation | HANDYBROS |
Тәжірибелік нұсқаулар және стиль
In this video, we will show you the concrete wedge anchor installation! We used Red Head Trubolt Wedge Anchor which is for heavy-duty concrete and masonry use. In this video, we will explain the whole process of installing the anchor along with providing tips and tricks!!
Thank you for watching the video!
Please like, subscribe, and leave a comment below!
This will help us create more DIY content for you!
** Related Videos **
◆ Remodel Front Porch ➔ • Front Porch Remodel in...
◆ DIY Patio Roof ➔ • DIY Patio Roof | HANDY...
◆ DIY Wood Fence over Wire Fence ➔ • Wood Fence Over Wire F...
◆ DIY Concrete Slab Part 1 ➔ • Concrete Slab for Begi...
◆ DIY Concrete Slab part 2 ➔ • How to do a Concrete S...
◆ Unboxing and Assembly of Ryobi Concrete Mixer ➔ • Ryobi Portable Cement ...
** Product/ Tool Links - USA **
◆ Red Head Wedge Anchor ➔ low.es/3n2YJHR
◆ CONFAST Wedge Anchor ➔ amzn.to/338F5Fc
◆ DEWALT Cordless Drill DCD996 ➔ amzn.to/3eZs83a
◆ DEWALT Cordless Portable Vacuum ➔ amzn.to/34my981
◆ DEWALT Impact Ready Deep Socket Set ➔ amzn.to/3n2neXy
◆ Work Gloves (Mechanix Wear) ➔ amzn.to/338hK6L
*Product/ Tool Links - Canada*
◆ CONFAST Wedge Anchor ➔ amzn.to/3dMrtBO
◆ DEWALT Cordless Drill DCD996 ➔ amzn.to/3CTMKUc
◆ DEWALT Cordless Portable Vacuum ➔ amzn.to/3s0qh5X
◆ DEWALT Impact Ready Deep Socket Set ➔ amzn.to/3GDzeGh
◆ Work Gloves (Mechanix Wear) ➔ amzn.to/3yjOiWR
The links may be affiliates that support the channel.
#WedgeAnchor #RedHeadTrubolt #DIY
Пікірлер: 209
I'm sure there are folks who think you did some overkill with your explanations, but those of us who don't do this much (and are new to it) appreciate the thoroughness and specificity provided. Excellent job!
@HandyBros
3 жыл бұрын
Thank you for your feedback, stay tuned for more exciting content!
@johnnyfletcher1961
2 жыл бұрын
I agree!!
6:03 Before to start to hammer the bolt, the nut must be placed to prevent from not being able to screw it onto the bolt due to damage on the threads.
@hughhopwood7421
11 ай бұрын
Its easy to overlook, but one stray strike with the hammer and the thread is toast. Always run a nut onto the threads as a protector and it gives you a larger strike face too.
@illwill718
10 ай бұрын
great tip... #pause
@mickdanvers1530
9 ай бұрын
just a knob head
@that1electrician
9 ай бұрын
@illwill718 I usually double, sometimes triple stack nuts onto the threads. Now you have a larger strike face, and more rigidity added to the anchor, it won't bend as easy.
5 ай бұрын
@@that1electricianHood idea using several nuts vs just one.
Thank you for the video. I want to build a patio arbor and I had no idea how to install anchor's in pre-existing concrete. You schooled me up!
@HandyBros
2 жыл бұрын
Glad I could help!
Wow you make this seem so easy. I thought this was going to be super hard. Thanks for the video.
@HandyBros
3 жыл бұрын
I am gald this was helpful!
Very well done, sir. Just the kind of detail and explanation a beginner needs.
@HandyBros
2 жыл бұрын
Thanks. check other video on our channel as well.
Thanks for taking the time to post this! Been wanting to use this style anchor, this really helps
@HandyBros
Жыл бұрын
Glad this was helpful.
This is an excellent video showing the process for installing these anchors! Very well done, thank you! Subscribed.
@HandyBros
3 жыл бұрын
Thanks Doug. Do check our other videos if you get a chance.
Thanks man I’m an apprentice In my job n never had to do this very helpful!
Excellent detailed example. Keep em coming.
That is the most thorough dust cleaning ever!
Thank you so much for making this video! 💗
@HandyBros
Жыл бұрын
Thanks!
Thanks for the video. Overall, it was great for beginners like me looking for simple solutions and not wanting to hire anybody for a simple job.
I have a parking post to install with supplied wedge anchors but no instructions at all. I had no idea how to use these and post fitting videos have various methods and bolts with sleeves and plugs. This is the first video I've found which gives thorough knowledge on how to use the bolts and how they work. Thank you, saved me hours of bodging and botching usually resulting in disaster.
@HandyBros
2 жыл бұрын
Thanks so much for your feedback. Do check our other video for more useful content.
Great video, very helpful, Thank you for making it sir!
@HandyBros
3 жыл бұрын
Glad that you enjoyed our video, stay tuned for more exciting content!
Tip : if you put your nut on before hammering the anchor in, you won't run into the problem of damaging the thread and not being able to put the nut on.
Helpful. Thank you
Great video
Nice video!
Very informative.
Nice video. You got the idea across well for me.
@HandyBros
3 жыл бұрын
Thank you so much for the valuable feedback. Hope you'll enjoy our other videos as well.
Excellent description, thank you! The step by step instructions were very clear.
@HandyBros
2 жыл бұрын
Glad it was helpful!
Thank you. Very good information
@HandyBros
2 жыл бұрын
Glad it was helpful!
Great 👍🏿!!
@HandyBros
2 жыл бұрын
Thanks!
This was very helpful. Wish I would've seen it before drilling 4 unnecessary holes into my garage wall...lol
Thank you
thanks bros!
@HandyBros
3 жыл бұрын
Thanks. Much appreciated. Do check our channel for other videos and subscribe for the future videos :)
Good job I appreciate it
@HandyBros
3 жыл бұрын
Thank you! Please do check our other channel videos for the exciting content.
Great video and information
@HandyBros
3 жыл бұрын
Thank you!! Stay tuned for more exciting content
Thank you for showing us I know how to do it now 😅❤
@HandyBros
2 жыл бұрын
Glad we could help!
Thank you 🙏
@HandyBros
2 жыл бұрын
You’re welcome 😊
thank you so much
@HandyBros
2 жыл бұрын
You're welcome!
Have fun destroying the threads and rendering the anchor useless. Attach the nut to the top of the bolt before hammering to protect the threads, will save you a lot of time and headache
@HandyBros
3 жыл бұрын
Thanks for the valuable feedback. I concur that having the nut on top of the bolt will surely protect the bolt thread from the hammer miss hits.
@jarskiXD
3 жыл бұрын
or just learn to hammer😎
@IVAN2233
3 жыл бұрын
That happened to me. Thanks for the tip
@nickle549
3 жыл бұрын
Just did this, now I know better. Is the only resolution to use a die set?
@e.r.6147
3 жыл бұрын
@Jared K - I disagree if you hammer 🔨 the top without the but it is safer than hammering with the nut on. Hammering with the nut on puts stress on the attached thread rows as you strike the hammer. Doing it your way is DUMB
I have those gloves... they are amazing!
@HandyBros
2 жыл бұрын
indeed. I'll add a link in the video description as well to help others :)
Never heard it called a Drill Machine but great video guys 👍🏼
@HandyBros
3 жыл бұрын
Thanks 👍
Thank you for making this video. I just bought a hammer drill to use to install an AC Guard Protector and drill it into concrete so was searching for the right video on how to drill into concrete and came across your video and it really help to what I'm looking to do. Thank you again!
@HandyBros
3 жыл бұрын
Thanks for the feedback. I am glad that the video was of help.
@ardabeats2025
Жыл бұрын
That is a drill hammer lol
Hammer it in with the nut on to avoid damaged threads. Hammer the nut not the bolt. Great video!
@HandyBros
Жыл бұрын
Good tip!
@Anthony-gy9ze
Жыл бұрын
I did that and messed up the thread now the bolt won’t go through and whole piece is just sliding
If you don't know how to use a drill or a vacuum cleaner, then this video is just right for you.
@HandyBros
2 жыл бұрын
at least you learned something out of this :)
Anchor will make us bank!!!
@HandyBros
2 жыл бұрын
which one? :)
Will this also work for stucco? Got a heavy sunscreen shade to hang but only have stucco on the outside no cement (cheap American construction). Not sure if the anchors will hold
I wish I saw this video sooner. This explains exactly what I didn't understand before regarding what drill bit size and how deep to drill. I didn't know these things and I ended up drilling a 1/2" whole for a sleeve that is way too small for it. The sleeve simply slides out and now I don't know what to do 😭
@HandyBros
Жыл бұрын
glad this was helpful
@nonoob65
Жыл бұрын
upsize to half inch anchor if possible
Good info, however one does not want to damage the threads while hammering into concrete. Ensue you have the nut flush with the threads prior to hammering into the concrete.
Using power tools to tighten a nut that requires a specific torque. No wonder your post is wobbling.
@HandyBros
3 жыл бұрын
Thank you so much for the valuable feedback. I totally agree with the fact that power tools should be avoided where a specific torque is needed. The torque required was high and we set the impact driver to low setting before driving. Thanks
@drkndn
3 жыл бұрын
1/2 x 3 3/4 requires 55ft/lbs of torque. That's not low torque. Even on low setting, you could've easily overtightened that nut 20-30 ft/lbs
@HandyBros
3 жыл бұрын
That's a great feedback. I'll definitely be cautious on the torque next time.
Very nice, but make sure you run a nut over the threads before you hammer it in so you don't damage them.
@richhoops2413
Жыл бұрын
This is a great tip! I learned this the hard way.
Can you do this into an unreinforced 4” concrete slab?
Will this work on wood 2x10?
Hi, i was trying to mount brackets for Ac condenser using 1/2" wedge anchor. I drilled holes using 1/2"drill bit. But the bolt and the threaded shaft kept on turning as i was trying to tighten. So loose i can pull the and out with plier. What did i do wrong? Thanks
Does this work with a 2x4 for a wall? I got the 5 1/2 length x 1/2.
I bought a pre cut shed from lowes and plan on putting it on an existing concrete slab so these wedge anchors should do the trick or longer ones?
@HandyBros
3 жыл бұрын
That's correct. You may to pick the size ensuring you achieve about 2.5 inch of bolt embedment.
When hammering a wedge anchor put the bolt on it and hammer against the face of the bolt so you don't destroy the thread on accident.
@HandyBros
2 жыл бұрын
thank you for the feedback. I totally agree!
To add. Be aware hitting soft metal too hard will expand the bolt and not possible to get nut on. If you drill a hole the bolt may only go in the hole part of the way.. tempting you to hit harder.. 🤔
@HandyBros
Жыл бұрын
great advice! Have the nut attached to the bolt before hammering.
how do you remove anchors??? and how to reuse them?? thank you
If you screw a barrel nut on the end you can use the hammer drill to drive the anchor down with less damage. Also it wouldn't hurt to use thread lubricant and depending if it's outside I would consider using stainless steel so it won't get rusty over time
@HandyBros
3 жыл бұрын
Thanks for your suggestion! They anchor bolts a re rated for outdoor use.
@truthalonetriumphs6572
7 ай бұрын
What bit do you use on the hammer drill to drive the anchor down?
Put the nut on the threads before hammering the stud, saves the threads
I want to install the pullup and dips bar that's out there into my wall in my apartment . Would you say this is strong enough to hold me up I'm about 170lbs? Thanks
@HandyBros
3 жыл бұрын
Firstly, This is for concrete or masonry application. I don't think this would work for the application that you are seeking even if you are anchoring it to concrete.
Nice! What if this attachment hast to be placed in a wall, and you dont know where the concrete is and where the blocks?
@HandyBros
2 жыл бұрын
if you have a solid block, you should be able to use the wedge anchors for them as well. However, I have another video for attaching a wood to the masonry wall using Tapcon concrete/ masonry screw. Do check that video as well!
What do you do to keep water from getting into the hole and freezing and cracking the concrete?
@MycobraII
Жыл бұрын
If pounding on the anchor with a hammer doesn't bust the concrete then I doubt ice would. I'm not a carpenter that's just my guesd.
What size would you use to attached a 2x6 ledger board
@HandyBros
3 жыл бұрын
at least 3/8 inch diameter with length about 4-5 inch
I drilled 10 or so holes for anchors in the time it took you to drill one.
@HandyBros
Жыл бұрын
Great job. Share with us what drill did you use? Was that a rotary hammer drill?
In manual book don’t let to use impact tool ?
@HandyBros
2 жыл бұрын
yes, avoid using impact driver to mistakenly over tighten the nut and damage the wedge end.
why is it still wobbly after you completed the install?
Does the post move? It looks like it was moving after
@HandyBros
Жыл бұрын
Due to the level arm created by the post, the base plate was slightly bending when the force was applied. However, the post was part of the patio roof that had other connections to the beams and cross bracing to provide stability.
Good for rock climbing anchors?
@HandyBros
3 жыл бұрын
Check the technical specifications form the manufacturer here: www.itwredhead.com/portals/0/fmproductcatalog/documents/products/39/trubolttechnicaldata.pdf I would assume, if installed right, they should work for the rock climbing anchors.
Good video. Thank You! For my part I would advise the viewer to don safety goggles before drilling.
@HandyBros
2 жыл бұрын
Good tip!
كم يحمل من قنطار في سقف
dooalt drill machine
Just a lil advice , never hit the bolt directly with the hammer , it's gonna damage the thread and the nut won't go through, always use a piece of wood over the bolt and then hammer it,.that'll save you time.
@HandyBros
Жыл бұрын
Good tip!
At the end it looked like it wobbles
@HandyBros
3 жыл бұрын
Thanks for your feedback. This may just be an illusion. The bolt held firmly and we atrached the post base plate for a patio roof column with no issues.
@MrEinniv
3 жыл бұрын
@@HandyBros haha an illusion. It fucking wobbled dude. Likely cause is using your driver to tighten rather than a torque wrench. On the package you showed it specified 55 ft lbs, drivers are great for driving screws but not so great at getting that specific torque.
@silver60618
2 жыл бұрын
@@MrEinniv Ive installed various versions of these, the one in the video is 16 gauge garbage, and did wobble. I went with the stronger 12gauge with 4x4 post and was able to lean on it 180 lbs, with minimal wobbling and movement
8 minute video for a 45 second job. I don't think I will call you anytime soon to do a deck job at my home.
Put the nut over that bolt as you are hammering it down into the concrete so you don't damage the threads.
@HandyBros
Жыл бұрын
it always better to put the nut over bolt before hammering.
i think he went a wheeeee to deep hitting the screw in, but good informative video.
@HandyBros
2 жыл бұрын
Thank you!!
🙏🙏🙏🙏🙏🙏🙏🙏🙏
The length is pronounced, “three and three quarters inches.”
@HandyBros
2 жыл бұрын
noted :)
Warning****** Never hammer down like that, it can strip the threads*****
@HandyBros
2 жыл бұрын
The best would be have the nut on the tip of the bolt before hammering.
Good video but you did not drill a recess hole for the nut and bolt in the post!
@HandyBros
2 жыл бұрын
Good observation. There was no need for a recess hole for the nut and bolt in the post. The post base came with a plate that goes on top of the nut and bolt thus elevating the post by about an inch.
Fun fact did anyone see the little bug crawling around😂
I'm using 1/2 so use 1/2 drill bit right
@HandyBros
3 жыл бұрын
typically that is the case. But do check with the instructions that come with the anchors you get just to confirm.
@mst5158
2 жыл бұрын
Did you end up using 1/2 drill bit? About to drill some today gonna be windy af tomorrow
Can you remove those bolts after? Or they stuck forever?
@HandyBros
2 жыл бұрын
those bolts are pretty much stuck forever. either you can fight them to take out or cut them.
@TheVitalij24
2 жыл бұрын
@@HandyBros ye but you can push them inside hole and cement on top ?
@HandyBros
2 жыл бұрын
the hole is typically drilled 1/4 in more than the embedment. so if you plan to push them bolt down in future, then consider drilling the longer hole when installing to you could push them in later.
@TheVitalij24
2 жыл бұрын
@@HandyBros yep thx
NEVER USE A METAL HAMMER TO HIT A THREADED BOLT!!
That was painful to watch the hammering of the anchor. Best way to hammer something with threads is to place the nut on the bolt and screw it on until it's flush with bolt, then hammer. That protects the threads, prevents the end of the bolt from mushrooming, and saves a lot of headaches.
thats literally a hammer drill
@HandyBros
3 жыл бұрын
That is a multipurpose drill with the capability of hammer drill as well. One of my favorite Dewalt tool.. The link to the drill is in the description.
Oh! Please put a nut on those threads before hammering or us a brass hammer. Otherwise you may mushroom the bolt.
@HandyBros
2 жыл бұрын
I do agree with you. One should always put the nut on threads before hammering.
0:45
@HandyBros
Жыл бұрын
Can you please elaborate? Thanks
@gashouse2738
Жыл бұрын
@@HandyBros what's kind of elaborate you want?
@gashouse2738
Жыл бұрын
you must be a bangladeshi i know that
Never tap or hit the bold and nut together They strip. It happened to me twice For paying attention to the stupid comments.
@HandyBros
2 жыл бұрын
Did you drill the right size hole? coz the bolt should slide in with a few gentle taps. The nut will help to protect the bolt from any miss hits.
Your screwing that into a paver?
@HandyBros
2 жыл бұрын
its a concrete slab.
WHAT IS MATERIAL USED, PLZ SHARE THE MATERIAL GRADE WITH FULL DETAILS. I AM WAITING for YOUR REPLY. IN ADDITION PLZ SHARE THE MATERIAL CODE FOR CARBON STEEL AND STAINLESS STEEL,
@HandyBros
3 жыл бұрын
The link to the material including the wedge anchors are provided in the description. You should be able to get the details from the product page or manufacturer's webpage.
@skid3339
3 жыл бұрын
Seriously bro just look it up lol
this is so wrong. U cant hammer the stud in like that. At least put the nut on first so you dont fuck up the threads
Always put a nut on FIRST before you hammer away. This was not smart
@HandyBros
2 жыл бұрын
That will definitely protect the bolt form miss hits. Thank you for the feedback.
@djaztec97
2 жыл бұрын
Can you explain why? serious question.
Too much talking😂😂😂
@HandyBros
3 жыл бұрын
Thank you for your feedback. The talking is intended for all viewers to understand the process as well :)
Thank you