Thank you for making this video! It was a great help in my review of short fiber composites. If you make more videos in the future I request that you make one on strength and stiffness calculations of randomly oriented short fiber composites. Cheers from Oregon State University.

@engineeringmaterials-tribo5142

3 жыл бұрын

Thanks a lot for your comment and suggestion. Will definitely consider in the future.👍

Thanks for your detailed explanation!

@engineeringmaterials-tribo5142

3 жыл бұрын

Glad it was helpful!👍

Great video, thank you!

@engineeringmaterials-tribo5142

3 жыл бұрын

Thanks!👍

Thank you for this video. It was really helpful in my research.

@engineeringmaterials-tribo5142

Жыл бұрын

👍

Thanks a lot for the video🙏🙏

@engineeringmaterials-tribo5142

3 жыл бұрын

👍👍

Great video sir. Learned the concept of critical length of the fibre

@engineeringmaterials-tribo5142

3 жыл бұрын

👍

Nice video. Thank you

@engineeringmaterials-tribo5142

3 жыл бұрын

welcome👍

Thank for the great video! Can someone explain equation 4.49 (32:40)? I made average strength calculations and couldn't get this exact expression.

Hi. Great video. I understand that the strength of long continuous fibre composites will be greater than that of short discontinuous ones. But how much of a difference will be there? For example, the difference between strengths of 2 composites, one made of a long continuous fibre of length l and another made of 2 fibres of length l/2? How will the load transfer be different? Thanks in advance.

@engineeringmaterials-tribo5142

2 жыл бұрын

Your question is very interesting and important. In theory, if the short fibre has length which is larger than the critical length then the short should be able to take the load similar to the long fibre. However, the short fibre composite bring other weaknesses (imperfections) just because of the presence of fibre ends. In further analysis given by Equation 4.50 in this video I have explained that for a short fibre composite to have higher strength, it must have the length of the fibre much larger than the critical length. Please watch the explanation just after Equation 4.50. Let me know if you have further question. 👍

@elmat_

2 жыл бұрын

@@engineeringmaterials-tribo5142 Thanks for your reply. I understood your explanation. But is there a way to calculate this difference? I actually have 2 laminates, each having 3 sections with different fiber lengths - top section (15mm and 42.5mm), middle section (220mm and 165mm) and bottom section (15mm and 42.5mm). The total length of both is 250mm. Using the formula mentioned, I can calculate the critical fiber length. I am interested in the load transfer between these different sections due to shear and to compare the tensile strengths of these laminates with another laminate made of just continuous fiber. Is this possible? Thanks again.

@elmat_

2 жыл бұрын

laminate 1- top 15mm, middle, 220mm, bottom 15mm; laminate 2- top 42.5mm, middle 165mm, bottom 42.5mm

greetings sir......This was a very nice video and very clear and simple ..... can you suggest me any reference book to study short fiber composite and calculate their stress strain analytically in randomly oriented position.....Thank you .... Keep up the work...

@engineeringmaterials-tribo5142

4 жыл бұрын

You may try Plastics Engineering by R J Crawford and The Mechanical Properties of solid polymers by I M Ward and J Sweeney. Thanks for the comment!

Is there any particular method to determine the shear strength for fibre-matrix interface?

@engineeringmaterials-tribo5142

3 жыл бұрын

Single fibre pull out test could be used. If you doing research then I would suggest an article or similar articles, www.sciencedirect.com/science/article/pii/1359835X9500069E

Hi if you rewrite Equation 4.30 in terms of aspect ratio , 4.31 will be: 𝐴/𝑉=(2𝜋/𝑉)^(1∕3) [𝑎^(〖−2〗∕3)+2𝑎^(1∕3) ] Please correct me if I am wrong . Thanks

@engineeringmaterials-tribo5142

2 жыл бұрын

Yes, you are right. Thanks for this correction!👍👍

In which machine, I measure tensile test of fiber composite ? Since , UTM machine available is only measure tensile test of metal only

@engineeringmaterials-tribo5142

Жыл бұрын

Please watch this video. You can use the normal UTM. kzread.info/dash/bejne/haFr1ZKyl9Xbp9o.html

Sir can you recheck the equation presented at the 20.21 min in the video? The equation number 4.34.

@engineeringmaterials-tribo5142

3 жыл бұрын

The equation is correct. Could you let me know what you meant? I have just replaced sigma f with sigma f max to represent maximum fibre stress value at the time of breakage. This will be equal to the tensile strength of the fibre. Please let me know your confusion.👍

@dr.mallikadatta2420

3 жыл бұрын

@@engineeringmaterials-tribo5142 Sir The equation 4.34 is derived through integration of governing equation after balancing of the tensile force and increment of the same by delta f due to shearing between the matrix and fibre AT ONE END over a diameter d (2* radius ) and length delta x of fibre. So after integration we are getting the expression for critical length. My confusion is about the presence of integer 2 in denominator. Sir kindly upload videos for calculation of critical volume fraction for ductile and brittle matrix

@engineeringmaterials-tribo5142

3 жыл бұрын

@@dr.mallikadatta2420 Thanks for your very relevant question. Here, there is no integration of Equation (4.33). It is based on the maximum stress generated for the breakage of the fibre. Breakage will occur at the point where sigma f is maximum and when this stress equals the tensile strength of the fibre. The shear stress tau y is same throughout and hence there is no need for integration of Equation (4.32) either. This is total force due to shearing. Hence, we do not have to integrate either of these two equations. We need to simply equate them as they are written. This gives us Equation (4.34). Finally, sigma y has to be made the ultimate tensile strength of the fibre. For any failure criterion, it is the maximum stress that is taken into consideration not integration of all the stresses. Thanks once again. 👍

Can you help me by providing the pdf book in which this lesson is located

@engineeringmaterials-tribo5142

Жыл бұрын

pdf of the book is unfortunately not possible by me.

How I measure shear strength of composite material. please suggest?

@engineeringmaterials-tribo5142

Жыл бұрын

If you meant the shear strength between the fibre and the matrix then you can conduct fibre pull-out test.

The analysis is for a single short fibre, for a number of short fibres, what is the cumulative strength of the composite?

@engineeringmaterials-tribo5142

Жыл бұрын

Cumulative effect can be brought in by considering the volume percentage of the fibre in the composite. Such analysis could be done using FEA as there are many such software.

Hi, Do we have an estimation criterion for calculating the equivalent E-modulus for certain Short fiber composites with only longitudinal isotropic E-modulus available( skin orientation). I have the temperature dependence data(isotropic).

@engineeringmaterials-tribo5142

2 жыл бұрын

There is no analytical estimation. You may use the finite element methods.

sir which book to follow

@engineeringmaterials-tribo5142

Жыл бұрын

Engineering Materials 2 by Ashby and Jones.