Comparing Foredom Flex Shaft Handpieces H.18, H.20 and H.30
Here we're comparing some of the most popular general use handpieces for the Foredom flex shaft. In this video we're looking at Handpiece number 18, 20, and 30. These are all available with a keytip or slipjoint fitting.
Foredom H.18 and H.20 are both quick-change handpieces, so you just press or turn a lever and then you can change your accessory. Both are fixed collet sizes, so can only take 2.35mm bits. Both a
Read more about the H18:
www.metalclay.co.uk/foredom-h...
Read more about the H.20:
www.metalclay.co.uk/foredom-h-...
Foredom H.30 is a chuck style handpiece, this means you open and close it with a key to change your accessory. Being a chuck-style it can take any bit with a shank up to 4mm. It is great as the basis of your Foredom Flex shaft kit, as you can get several add-ons for it. Some of Foredom's useful add-ons are the Foredom Drillpress, a Angle Grinder, and even a Belt Sander!
Read more about the Foredom H.30 handpiece:
www.metalclay.co.uk/foredom-h...
Пікірлер: 23
Great explanation of the differences between these handpieces!
@petracameron4486
3 жыл бұрын
Thanks guys! And thanks for making such great handpieces. :)
Great video thank you for your thorough comparison.
@Metal-Clay
3 жыл бұрын
Glad it was helpful!
Thanks for this useful explanations
@Metal-Clay
2 жыл бұрын
Glad it was helpful!
Thank you so much! This was really helpful! 👍
@Metal-Clay
2 жыл бұрын
You're very welcome! :)
Thank you, that was so useful x
@Metal-Clay
2 жыл бұрын
You're so welcome! Pleased to hear it was useful.
very informative. helps me make my decision. thank u!
@Metal-Clay
2 жыл бұрын
Glad I could help!
Thanks, super helpful. Since this video was uploaded two years ago, maybe any other new sizes apart from these 3 can be considered? I can also see many different Foredom handpieces on your website so not sure which one to buy. I need the size can fit burrs larger than 3mm. Thanks.
@petracameron4486
2 жыл бұрын
The H.30 will take up to 4mm. The H.28 has a 3.18mm collet. And for larger burrs, look at H.44 which has optional fixed collets in different sizes up to 6.4mm. Hope that helps!
Does anyone know how I replace a broken quick release lever on the h20? It looks like a spring loaded piece inside needs to be depressed but I can’t see how to do this while bolting the handle into place
@Metal-Clay
2 жыл бұрын
Hey Simon, so sorry we missed this comment. I'm assuming you've resolved this one way or another by now. If not, let me know and I'll check in with Foredom.
Aku menggunakan handpiece t30
@Metal-Clay
2 жыл бұрын
It's a great all rounder handpiece!
Do you know if any of these handpieces can be used with the Dremel Fortiflex 9100?
@frugalforge3657
4 жыл бұрын
If that uses the key tip type shaft it will
Hello, can i put the H30 in H20 flex shaft?
@petracameron4486
Ай бұрын
Hi! To clarify, there is no such thing as an “H20 flex shaft”, the Foredom motor flexshafts come in keytip, slip joint, and square type. You have to check what type of flexshaft you have (the most common one is a key tip style); when you know what type you have, the hand pieces are interchangeable and you will be able to find an H30 that will fit the same shaft as your H20. 👍🏻
@belpheglor7866
28 күн бұрын
@@petracameron4486 thank you