You breezed so fast through those tension issues at the beginning - you didn't show if the stitches were different at the different tensions

@jillsmith5687

2 жыл бұрын

I agree Patricia; I wanted her to explain about the tension spring in bobbin area; my bobbin is jumping and clunking; and the bottom stitching is really tight! So can anyone help with this plz?

@Winthrop1981

Жыл бұрын

Would’ve been SOOOOO helpful

@evangelineboyles4784

8 ай бұрын

Agreed. I need to see a slow close up of what those look like!!!

@kathleengreen6889

7 ай бұрын

I need to see exactly how Angrla’s three dials are set..I am going crazy!

@ke8qr

6 ай бұрын

@@jillsmith5687 how do I fix the tension in my bobbin thread

This 1000% did not touch on ANY of the issues I'm experiencing! 🤦🏻‍♀️

@Kandaharkitchen-onlyorganic

9 ай бұрын

Same😢

@AsrafulIslam-hw5xl

9 ай бұрын

@@Mataylor17 mrp 2sat.frog

@Jen-pj7nc

6 ай бұрын

same@@Kandaharkitchen-onlyorganic

@LoriBounds-wt1vc

5 ай бұрын

Me either. The part on top looks like the wire might be in wrong pasotion. I do not know where it goes?

@AriDimitris

4 ай бұрын

I've had to unscrew the plate and fix the bobbin holder countless times, AFTER exchanging the machine four times already..I finally gave up working on my project until I can exchange the machine AGAIN!

For me, it was a loosely threaded bobbin. I just put a new bobbin on the winder, and re-wound to the new bobbin. Fixed my tenstion problem. I do appreciate how the tension adjustment was shown - I had no clue! This is a good troubleshooting video, thanks!

@BrotherSews

8 ай бұрын

Thank you for watching Charlie and we are glad that you found the video helpful!

I was getting so frustrated. Thank you so much, it totally fixed my problem with the nest!

@stephawesome2128

3 ай бұрын

What fixture problem? I couldn't follow the video.

I watched this video because I am brand new to sewing and right out of the gate I am having tension issues. I even had trouble following the manufacturers issues on how to thread it. You covered both issues, but the filming of your bottom hand when all the action was going on at the top of the machine with your upper hand was absolutely crazy.

Had an issue with my FS101, was getting bird nests underneath each sewing start, for about 1 to 2cm birdnesting. Studied KZread videos for hours and tried everything, nothing solved the nesting. New needles, new and different thread, new threading, cleaning, nothing solved the birdnesting at the beginning of each sewing. Saw nothing wrong on the bobbins or the bobbin casing. Ordered by coincidence recently 2 spare bobbin cases. Gave it a try and changed the bobbin case and voila, no more bird nests at all. Even so I could not tell what was wrong on the "old" bobbin case, the replacement of the bobbin case was the solution to the problem. Just in case, as this is not mentioned as possible troubleshoot solution ;)

@awesomesaucezz

9 ай бұрын

god bless you and your crops

Wow the tension stitches were explained so well.

@BrotherSews

2 жыл бұрын

Here is a link that may help with tension as well: help.brother-usa.com/app/answers/detail/a_id/129182 If you need any further assistance, please contact Brother Customer Service at: www.brother-usa.com/support

The tension knob!!!!!! Thank you for your help!

Thank you so much! My dog ran through the cord that was stretched over to the outlet and my sewing machine flew through the air and broke apart on the floor. I got error code e6 so found your video. My sewing machine is working again! Thank you! My son just got interested in sewing and I was so upset that my machine got broken.

@BrotherSews

Жыл бұрын

Thank you for watching and we are glad to know that your machine is working!

You might want to show the tension samples for more than a split second.

Thank you woman! You deserve a reward.

How do you fix the internal threading spring in position #3 on the Brother inovis 1750 d sewing machine? I can stitch about 15 stitches, then the spring sticks and I get an error message to check and rethread upper thread. Upper thread is fine, it's a problem with this spring that is supposed to go up and down with EVERY stitch, but doesn't. Thanks!

Girl I could hug you!!!!!!!! You're a total life savor! I was sooooo sick of this sewing s--t! I came close to throwing it in the dumpster along with my expensive fabric. Couldn't figure anything out. It wouldn't feed through, and I had to pull it! You're knowledge has me on the road to a gorgeous little quilt, and I thank you so much! My husband thanks you even more 'cause now he doesn't have to hear me whining about it!

@AngelaWolf

2 жыл бұрын

thanks Karen :) Happy sewing!

@Lace4Life

11 ай бұрын

me too!

My Brother GS3700 model ,only function normal stiching.nothing happened when I select others.appreciate your help

Hi I find the lighting on my Brother GS3710 is not great, how do I change the globe to get better light. Thankyou!

I’m brand new to sewing. What my wheel thing on the right doesn’t turn enough to have the notches line up? I keep getting a majorly grinding noise, have been checking for lose threads in the bobbin area, etc, but no luck. I’m borrowing the machine from our local library and it’s a Brother CS-6000i. I’m afraid that I am somehow damaging the machine.

Hi, I have brother sewing machine Ls-2125. Once I was sewing my dress. On my dress has a thicker embroidery when I started sewing the thread was broken. I also changed needles & different types of foot and stitches number. Can you tell me please problem.

I followed the troubleshooting FAQ on Brother and watched this vid - which basically summarizes those FAQs. I am a good engineer and this Brother CS7000i has NEVER stitched anything without leaving a nasty bunched up mess on the underside. The top looks fine. However, even when I have a long stitch. It will start with a little bunch or hang. Then, I can continue for a couple of inches where it looks great and then randomly the last two inches are a rats nest. Fortunately, it is mostly when I am repairing my old work jeans. That material is 9 ounce twill and I am backing up the rips and holes with one of those (pathetic) iron patches that never iron on. So, I am doing only straight stiches with the correct default foot. Medium duty pure cotton twill thread on the needle and bobbin sides. Not one thing other than all default settings. Tension set between 1 and 2. Hand start and hand tack beginning and end (using the wheel, not the foot pedal). You can conact me here with any bright ideas!

@BrotherSews

4 ай бұрын

We are sorry to hear that your CS7000i is not sewing correctly. Please see the links below for more informaton: help.brother-usa.com/app/answers/detail/a_id/124056 support.brother.com/g/b/faqend.aspx?c=us&lang=en&prod=hf_cs7000ieus&faqid=faqh00000004_000 If you continue to experience the same issue, please contact Brother Customer Service at: www.brother-usa.com/support

@tashatomic4893

3 ай бұрын

Hi @allanbruce9473 - did your machine continue bothering you or was there any "cure"?

Great tips but I have an issue that I can't figure out. I set the machine for a simple zigzag stitch and after I sew about an inch the length dial automatically rotates backwards to "0". What am I doing wrong?

do you know how to fix the error f05 speed sensor on a se400 machine?

This video helped to solve my GS3700 mechine problem.. Thank you

i have a SE 400 brother sewing and embroidery machine but the needle locked up is that a safety thing or what caused that i can’t get it to work

1:26 solved the issue with clicking noise for me, thanks a lot

The knob for stitch selection has broken off is there any repairs available or is if some thing that cannot befixed

my gx37 arrived a couple of hours ago. i watched 2 videos about the exact machine and did everything according to the videos. i am a master threader now both lower bobbin and the main thread. buuut my machine just wont sew. i hear the motor whirring but nothing moves. i checked the manual, the troubleshooting section. made sure the bobbin winder shaft is on the left. tried 3 different power outlets. nothing. i rethreaded the machine 3-4 times. it worked like 1 second when i first tried it. then nothing will make it work again. also again after that first time, the needle threader wont reach the needle anymore. when i pull it down and push it forward, the walls of the needle threader is short a couple of millimeters behind the needle.

If you please please tell me how I solve mypronlem it is my lower part of the cloth are coming out with huge tangle thread,how to solve?

My brother xr9000 has F1 error. There is no authorized service center in my country. Any help in how to fix this??

How to replace the footplate cover plate to ensure the automatic thread cutter works. I took mine off to clean the fuzz out and now the thread cutter won't work. Everything else is working just fine.

Hello I have a ae1700 brother sewing machine the hand wheel is steff please tell me what to do

Thank you so much for this video! It came in handy! Thank you brother! 😁

I needed to see the bottom stitches each time you changed the tension. You just showed the top stitch

@wandaherring7526

5 ай бұрын

Agree

@gkpleasants1

4 ай бұрын

I agree.

Thanks so much! I have a question and hopefully anyone can answer. When I back stitch, the thread from the bobbin get undone and I see loops through the top. Thank you so much for sharing

@legacycosmo

2 жыл бұрын

@@BrotherSews I’m new to sewing. I’m going to try changing the needle. Wish me luck hehe. Another question, do you suggest to only use Brother bobbins? My husband bought me some bobbins to surprise me but they are Walmart brand, haven’t sued them just to be safe. Thanks in advance

@elsapadfield2548

Жыл бұрын

@@legacycosmo I’m sure you’ve had a reply but if the bobbin fits into the bobbin spot, they’ll be fine. I have some that won’t fit on the spindle….? Whats that about?

Hello on the pot that you cut your thread does that part come off I have thread Stuck in number four when I’m threading the machine does the side piece come off the one that cuts the thread

Hello, I have a brother lx3817, the needle hitting plate. I want to move the needle bar, please how to do. Thank you

Good rips. Thanks.

My Brother JX2517 is having an issue for the first time since I bought it in 2017. As I’m ready to push the pedal to sew, the needle doesn’t move but I hear the machine or the machine’s gears inside trying to work or move. So I try to push and let go and push the pedal and then maybe after 10 times of doing this, it starts to sew but very slow then go fast after many stitches. Then when I stop after minutes, it goes back to the same problem again. Please let me know how to fix this? Thank you!

@shahedafaisal

3 жыл бұрын

I am facing the same problem the needle does not move at all

These were all great tips & helpful. I'm a beginner beginner with a sewing machine. Thank you so much 👏

@BrotherSews

Жыл бұрын

Thank you for watching Janice! We are so glad that the information was helpful.

It was definitely the tension that was messing me up 😩 my first time quilting and I’m using the walking foot. The bottom thread would just be a mess in the back and I was getting so frustrated why it wasn’t working. I checked everything from bobbin to replacing the needles. You said it might be tension and I put it up a bit higher and it came out perfect on the back!! If you’re using a walking door defiantly put it up around 4-5

@BrotherSews

5 ай бұрын

Thank you for watching! We are glad that you were able to resolve the issue so that your stitches look great on the front and back of your quilt.

Does anyone have a PS-53 ? there seems to be a problem with the reverse lever as it makes no difference up or down, the machine only sews in reverse. Is there a setting that would fix this? TIA

@BrotherSews

Жыл бұрын

It is frustrating when a machine will not sew forwards. Please see the link below for further assistance: help.brother-usa.com/app/answers/detail/a_id/124798 If you are still having the same issue, please use the Brother global locator link below to locate a Brother group to assist you with Brother products in your area: www.brother.com/brgnet2/hsm/index.htm

Thank you so much. This was really helpful and fixed all my problems '

@BrotherSews

6 ай бұрын

Thank you for watching Ben! We are glad that the video was helpful.

Thanks sooooo much!!! I loved your explanation

@BrotherSews

Жыл бұрын

Thank you for watching and we are glad that you found the video helpful!

Any suggestions? I am trying to do zigzag, and it looks like a ladder stich on the front, and zigzag on the back. I have re-threaded the machine and bobbin, changed tension, and I am not sure how to fix it. I have a CS-6000I

@BrotherSews

Жыл бұрын

We are sorry to hear that your zigzag stitch is not sewing properly. Please see the links below for more information: help.brother-usa.com/app/answers/detail/a_id/128038 help.brother-usa.com/app/answers/detail/a_id/55602 help.brother-usa.com/app/answers/detail/a_id/55775 If you are still experiencing the same issue, please contact Brother Customer Service at: www.brother-usa.com/support

My GS2700 always making some bad understich, like the upper is neat but the under is Curly(?) nest or hanging , i've tried all the thing on the video but all is fail i still got the curly stich. Oh i'm sewing some cotton twill not that thick.

Omg I just realized that my issue was right by the needle itself.....I kept threading it through the machine minus the piece right above the foot and needle🤦🏼‍♀️

Hi I have my teddy 600 brother sawing machine and I don't know how to oil it

My machine is 6 wks old and now wont zig zag or other stitches. It will do straight but makes a loud knocking noise. I cant return it. Whats up? I've rethreaded it, replaced the needle and cleaned it.

What if the bobbin case spins with the shuttle?

What can I do to use brother sewing machine from the US that has 110v input in 220v mains?

@BrotherSews

Жыл бұрын

We do not recommend using US models outside of the US, as they are manufactured for 120v use. Performance may vary between transformer manufacturers and as such we cannot guarantee results. I would recommend using the Brother Global locator to find a Brother facility nearest you, to purchase a machine manufactured for the voltage specifications for your area: global.brother/en/gateway

Having a problem with my Brother 950D embroidery/sewing machine. Have a PES 4 inch embroidery pattern on a SUB stick that is not being recognized by the machine. What am I doing wrong?

@BrotherSews

2 жыл бұрын

It is frustrating when the design does not show on the machine or a usb is not working. Please see the links below for more information: help.brother-usa.com/app/answers/detail/a_id/70510 help.brother-usa.com/app/answers/detail/a_id/152667 If you are still experiencing the same issue, please contact Brother Customer Service at: https:www.brother-usa.com/support

Hello ! I have a Brother PS-2500. The pattern selector dial rotates all the way back and forth but the pattern does not change. It’s stack on 4/22 position on the display window. Any way you could help me to fix this ? I called a service technician but the cost of checking the machine and fixing it is higher than buying a new machine. I love m’y existing machine and I have a sentimental attachment to it since it was my mother’s machine. Thank you to anyone seeing this post and helping me to fix this.

@BrotherSews

Жыл бұрын

It is frustrating when a machine is not working properly. We are sorry to hear that your pattern dial is not changing. We recommend you contact one of our Brother Authorized Service Centers for further assistance and to have your Brother PS2500 evaluated. You can locate the closest Brother Authorized Service Centers using the following link: www.brother-usa.com/dealer-locator

I appreciate , very informative, thank you, learn alot.

@BrotherSews

6 ай бұрын

Thank you for watching! We are glad that the information was helpful.

Thank you very much can I vacuum bottle of sewing machine to get the debri out ?

@BrotherSews

Жыл бұрын

You can use a cleaning brush or a small vacuum cleaner to clean out Your Brother XR3774 or similar sewing machine. Please see the link below for more information: help.brother-usa.com/app/answers/detail/a_id/64226

Thank you so much ❤

I have a innovis 4000d I pushed the needle threader button then pushed it again before it finished now has malfunctioned and the display is showing tg-pm. Turned it of and on. Still nothing, any guidance would be greatly appreciated.

@BrotherSews

11 ай бұрын

We are sorry to hear about your NV4000D malfunctioning. Please contact Brother Customer Service directly at: www.brother-usa.com/support

What about the brother machine ce 1150 where there’s no tension dial???

@BrotherSews

5 ай бұрын

The tension dial for the Brother CE1150 is located above the needle. Please see the link below for more information: support.brother.com/g/b/faqend.aspx?c=us&lang=en&prod=hf_ce1150eus&faqid=faqh00101020_004

what do i do if my zig zag stitch isn’t picking up on the right side on a brother cs 6000i ? i can’t find any tutorials showing how to fix timing ?

@BrotherSews

Жыл бұрын

It is frustrating when a zigzag stitch does not turn out correctly. Please see the link below to help with more information: help.brother-usa.com/app/answers/detail/a_id/65145 If this does not resolve the issue you are having, please contact Brother Customer Service at: www.brother-usa.com/support

Thanks , it helped

Tried the tension, changed the neddle, cleaned bobbin case area, but top stitch still not picking bottom stitch. Could this be a hook timing issue? How do i fix this gs2700 brother machine. Thanks.

@sweetscent76

3 жыл бұрын

@@BrotherSews Thankyou, appreciate it.

my Brother CPV70 compter machine w/ 11 stitches modes won't reverse and stuck sometimes, also just running in straight line mode in very low speed . i just tried to screwed up and cleaning using air dust and put some oil but the reverse stitches still doesn't work. all stitches mode are perfectly working thou

@BrotherSews

Жыл бұрын

Thank you for watching and your interest in Brother machines and products. You have reached Brother USA. Please use the Brother global locator link below to locate a Brother group to assist you with Brother products in your area: www.brother.com/brgnet2/hsm/index.htm

Good morning, i have a brother's VX 1435 when sewing fabric not sewing. Can someone tell how to fix it please

@BrotherSews

6 ай бұрын

We are sorry to hear that your Brother VX1435 is not sewing. Please see the link below for more information: help.brother-usa.com/app/answers/detail/a_id/65149 If you continue to experience the same issue, please contact Brother Customer Service at: www.brother-usa.com/support

My boyfriend drilled into the wall and my brother 2800 was filled with dust. It is not sewing a stitch. I cleaned out the bobbin case and it still doesn't stitch what can I do to fix it. I tried all that you did in this video but it's the same. Do you have any other solutions? Anyone ?

What if it only catches one stitch and the needke slips out of the needle?

My NV880e embroidery machine needle bar has started vibrating please help thanks 🙏🏼

@BrotherSews

10 ай бұрын

We are sorry to hear about your Brother NV880E. You have reached Brother USA. Please use the Brother global locator link below to locate a Brother group to assist you with Brother products in your area: www.brother.com/brgnet2/hsm/index.htm

I have a Brother sewing machine just like the one in the video. However, it pulls to the left. How can I fix this problem?

@danamarie6066

3 жыл бұрын

@@BrotherSews Hi! I have the xm2701 model and my machine is stuck i reverse. Help!

The bottom thread does not seem to want to stitch along with my top thread, it wouldn’t simply not connect to my fabric. I have tried rethreading the bobbin and the top thread, and I can’t seem to find the issue. Any ideas on how to fix this?

@carolinej3661

4 жыл бұрын

THAT is the problem I keep having! I was hoping to find an answer here - but she didn't cover it…..Funny thing is, I will go along fine sewing with different threads and different stitches, and then, suddenly, this problem will recur! No amount of tension adjusting and re-threading will solve the issue......

@rainierhuang5848

4 жыл бұрын

My bobbin thread is to losses, which top thread always bring it up. .cannot do any stitch now ....

Well the brother machine I have is cs-80 and the problem with it is the error it shows is .."machine locked, check for James threads. I look, and nothing It sounds like a loose nut is bouncing around in the gears. Really loud. Hope someone can help.

I bought this exact machine last week it’s awful I usually love brother machines but mine is so noisy & vibrates badly I’ve asked seller if I can send it back as it’s definitely not right & as I see everyday I’ve had to buy another machine I’ve going back to the brother ls 14 which in my opinion is the best I’ve had 3 now & wanted an upgrade but this is definitely a down grade

What if you have done everything and it still doesnt see but the motor works?

My thread keeps coming out of the needle thread guide. How do I fix this?

@jennifergris6275

3 жыл бұрын

Are you holding onto both of the threads at the back, when you start to sew? That will help.

hi. good day. my brother sewing machine is no foot pedal. my concern is how can i thead the bobbin without pedal?

@BrotherSews

Жыл бұрын

Thank you for watching. We apologize for any inconvenience. Please contact Brother Customer Service so we may be able to assist you further using the link below: www.brother-usa.com/support

What making the holes in a mustache end of sewing machine I gave it all brother machine

My is Bobby problem that make it difficult to be used

Hi, I ha e brotherLX27NT sewing machine. Sometimes, Inspite of cleaning lint and kepping the bobbin & underneath bobbin, one unpleasant sound remains as if , any part got detached internally. What could be the problem. Can you please explain. Waiting eagerly for your valuable response. Tq😊

@BrotherSews

Жыл бұрын

You have reached Brother USA. We apologize for any inconvenience. Please use the Brother global locator link below to locate a Brother group to assist you with Brother products in your area: www.brother.com/brgnet2/hsm/index.htm

My Brother sc6600 is not working. The engine runs but the needle does not move. What can I do to fix it?

@yusleidydelgado307

3 жыл бұрын

Same!! I have a different model, but mine won’t either. I hear the motor going but it’s like a belt is off or not engaging. Hope to find an answer soon

Thankyou...You saved me from going to the service center 🙏

@BrotherSews

Жыл бұрын

We are glad to know that this video was helpful! Thank you for watching Irene!

Thank you for this video. However, I need help with my JC14 Portable Free Arm. I was stitching a thick fabric and I discovered the needle bar shifted. So I took it for repair they couldn't fix it. I took to another technician and was told the Crank is broken and so the machine is now useless. What do you suggest I do about this please?

@BrotherSews

10 ай бұрын

We are so sorry to hear about your sewing machine and this frustrating experience. You have reached Brother USA. Please use the Brother global locator link below to locate a Brother group to assist you with Brother products in your area: www.brother.com/brgnet2/hsm/index.htm

@afridora9362

10 ай бұрын

@@BrotherSews Alright. Thank you so much.

@afridora9362

10 ай бұрын

@@BrotherSews I just clicked the link you sent and discovered I've done that few months ago. I found some contacts here in Nigeria. But after relating the issue with them. They suggested that I buy a new sewing machine instead of spending so much to fix the bad one. Even though they didn't tell me the cost of fixing it. Am really disturbed about this situation.

The step 4 part of threading is not looking right on my machine. Someone help!?

I need help if anyone could. My brother sewing machine motor is running but needle and feed dog doesn't move.but when i rotate the needle wheel, both moves.i am new to sewing. Please help!!

I did everything correctly from your cd device and bought the essential model, but thread from the stitches do not place through the fabric. What do I do?

@BrotherSews

6 ай бұрын

We are sorry to hear that your machine is not sewing properly. Please see the link below for further assistance: help.brother-usa.com/app/answers/detail/a_id/65149 If you continue to experience this same issue, please contact Brother Customer Service at: www.brother-usa.com/support

i took my brotherst531hd to the shop for a timing adjustment and was told they are disposable machines that cannot be accessed to do internal maintenance or work on the timing gears. wtaf?!!!!!

@BrotherSews

2 жыл бұрын

We would love to hear more about your experience and further assist you with your Brother ST531HD. Please contact Brother Customer Service at: www.brother-usa.com/support

Hi: I'm not sure how to fix my presser foot. When I lower the lever, the foot snaps down with a lot of force, and feels like it is permanently stuck at the highest tension. Do you have any tips, or is the machine unfixable?

@janesmith4617

Жыл бұрын

I know this is late, but there should be a dial or knob to turn to reduce the pressure of your presser foot. Check the manual for that, or look online.

my brother-xl 3022 want go forward only goes in reverse

@danamarie6066

3 жыл бұрын

Im having the same problem!

My NX400 just wont sew. Ive cleaned under bobbin & needle with brush & vacuum. Rethreaded & reset bobbin over & over again & changed tension setting. The balance wheel turns a little then freezes to a stop with LCD saying its a safety issue! Help, please!

@BrotherSews

9 ай бұрын

We are sorry to hear that your NX400 is not operating correctly. Please see the link below to help with the "safety device has been activated" error message": help.brother-usa.com/app/answers/detail/a_id/151940 If you are still experiencing the same issue, please contact Brother Customer Service at: www.brother-usa.com/support

My tension got completely tight during sewing and machine stopped help

I have an issue it was working fine.. I was foinf a project simple straight stitching. it worked all day... Then I took my foot off the "the foot" to get another piece of material and it won't go... Nothing it just stopped... no bobbin problem... the light is on... you press the foot nothing happens the motor won't go is it the foot dead or the whole machine??? I'm baffled... it was working perfect and just stopped... can you help?? tyia

@Justjoszie

3 жыл бұрын

@@BrotherSews ty for such a prompt response. I called it may or may not be the foot pedal. Unfortunately, there's no dealer near me and I don't have a credit card for online purchases.. or anything left to spend after all the the others supplies I needed to do this project... it's.the end of my sewing road. Your customer service is remarkable just heartbreaking as it was keeping me busy and creating in these troubled times... It's just baffling I did over 10 yards in a straight run of mini "snip-it rolls" not one hiccup... took my foot off the the pedal and she went on strike... lights goes on and no one is home... thank you again to you and the brother team take care

I have a problem that...the needle is touching on the tension plate...and needle get broken....how can I fix it

do any one experience here that their peddle is not working....can you teach me on how to troubleshoot

How about the timing? Can we fix it without opening the cover?

@ednascrase2677

4 жыл бұрын

Yes I need advice on that problem too

Hi, I have brother LX27NT. For past few days, My machine is making lot of noise and top thread is getting cut frequently. I replaced to new needle. Took off pressure foot, and also, removed needle plate by unscrewing. Removed all the lint, wiped with cloth and replaced everything in respective order. Still the problem is occurring. Please tell,how to set it right.? What could be the problem.? Eagerly, waiting for your suggestion. 😊

@BrotherSews

Жыл бұрын

We apologize for any inconvenience. You have reached Brother USA. Please use the Brother global locator link below to locate a Brother group to assist you with Brother products that are available in your area: www.brother.com/brgnet2/hsm/index.htm

So what’s the reason for the tread pulled and gathered in a nasty nest under the needle plate and even the fabric being eaten down there as well ? You just showed us how to remove the mess but how do I stop it from keeping happening? It’s happening all the time that I want to throw my new machine in the garbage 😭

I am a beginning who is self taught what is a good thread to use? For cloth and tulle

@BrotherSews

Жыл бұрын

Thanks for watching Jessica! Please see the link below for thread,material and needle combinations for the Brother XR3774: support.brother.com/g/b/faqend.aspx?c=us&lang=en&prod=hf_xr3774eus&faqid=faqh00000004_000

How do I resolve a problem when the fabric is not feeding when the needle is sewing?

needle keeps going through fabric and stabilizer getting stuck under. It happens every timeeeee. I’ve gone through like 10 shirts. changed needles, lowered tension.. idk what’s going on

@BrotherSews

8 ай бұрын

We apologize for any inconvenience. We would like to help. Please contact Brother Customer Service at: www.brother-usa.com/support

She does stitches with little then a lot of tension but them doesn't SHOW you what they look like! My problem: I sewed fine 2 days ago. I didn't change the thread or anything. Now I just went to use it & the first couple of stitched made noise. Well when I manually & slowly moved the needle down (it is in the left position) it is banging into something below. You can see at that time that the needle is 'bending' a bit to the right. If it were to go straight down it surely would break. WHAT is the issue? Also I haven't been able to use the auto threader. To get the needle into the hook, I must push the needle by hand to the left to get in. But I still can't use it because the threader bar does not go low enough to line up behind the eye of the needle. Can this be adjusted somehow?

@petmama

4 жыл бұрын

I forgot to mention, my machine is a cs6000i

@petmama

4 жыл бұрын

Ok so I found that I had the bobbin thread facing the wrong way. WOW, who would think that other than having a crappy stitch that the needle would hit the plate below just from having a thread wrong way? Now I get an E6 error! For some reason now the auto threader lines up right. I tried about 30 times & got the thread to go through only once.

@rubydown3329

Жыл бұрын

OMG you probably don't remember commenting this, but you totally solved my problem when this video couldn't 🤦🏻‍♀️🤦🏻‍♀️ I was going nuts trying to fix everything but it was just backwards bobbin thread LOL

@petmama

Жыл бұрын

@@rubydown3329 Funny I just happened to see your comment. Glad I was of help!

How do you keep the thread from tearing or falling out. Im running into that problem

@BrotherSews

Жыл бұрын

When the thread breaks or the upper thread comes unthreaded, it can be frustrating. Please see the links below for further assistance: help.brother-usa.com/app/answers/detail/a_id/70909 help.brother-usa.com/app/answers/detail/a_id/74446 If you are still experiencing the same issues, please contact Brother Customer Service directly at: www.brother-usa.com/support

I think my presser foot lever is broken. When i push it down, the presser foot does not move down. It doesn't move at all... how do I fix it please?

Why cant i make the machine go slower. I barley press the pedel on my brother xl2600i and it still speeds like a grandma on a highway 😐

Ive done all of these steps several times my machine is still making a horrible nest of thread on the bottom help

@elizabethmalone1079

3 ай бұрын

I’m having the same problem. I’ve watched several videos and have adjusted the tension, but nothing helps. I have re-threaded the bobbin and needle repeatedly to no avail.

@gordonmorgan3131

3 ай бұрын

@@elizabethmalone1079 i turned my machine off for a week and it started working again so it may of just gotten "mad"

I’m having problems with the top thread snapping whilst I’m sewing tee shirt fabric. It sees other types of fabric. I’ve changed the tension and tried everything! Help!

@BrotherSews

Жыл бұрын

It is frustrating when the thread breaks. Please see the links below for more information that may help: help.brother-usa.com/app/answers/detail/a_id/124196 support.brother.com/g/b/faqend.aspx?c=us&lang=en&prod=hf_xr3774eus&faqid=faqh00000004_000 If you are still experiencing the same issue, please contact Brother Customer Service at: www.brother-usa.com/support

@elsapadfield2548

Жыл бұрын

@Ghee tyxxxrt yes. I rang Brother and they told me to change the needle to the one they recommend. It works perfectly!

Ok, that explains a lot. Could you please go into detail about the auto threader, there is nothing that explains it

@BrotherSews

6 ай бұрын

Thank you for watching Joseph! Please see the video below for how to thread a mechanical sewing machine with or without the automatic needle threader: kzread.info/dash/bejne/ZZqh0KOrhae5ksY.htmlcc_load_policy=1&rel=0