Followed your video and it went flawlessly. Shade Tree mechanic, no lift, on the ground with jack stands and a floor jack. Tranny was out in 3 hours, flywheel resurfaced in a day and back together in the next day. Thank you for this, it was a huge help....mostly with the electrical connections and the engine cradle. I did drop it as it was just easier than trying to make that gap. Great video, detail and instructions. Thanks....2 thumbs up!!

@ELCLAVE300

Ай бұрын

How long did it take to put the transmission back?

I've been driving with a broken clutch for years this is what I was looking for thankyou!!

The best mechanic ! Thanks for sharing ! Respect man !

Great detail, just what I needed, thanks. Will let you know how it goes!!

Awesome job, guys! Thank you for detailed instruction.

Thanks for the content great as always!!

Super helpful. thankyou for sharing. Im certain i found the manual for this on the webb months ago, but cant seem to find it again . 🙃

The throw out bearing rides on an aluminum tube? Cast into the transmission housing? Ouch! Thank you for sharing.

How do you repair the grooving?

I'm hoping you might be able to give me some advice on my 2010 touring the shifter Acts like the cable is loose but everything else is moving even when the car is running it will shift without the clutch being depressed no grinding noise but when it happened it made like a little breaking noise like I snapped something I just got new pressure plate and master cylinder now it seems like the cable broke but I'm old school I don't really know about front will drive? anything you can tell me please do thank you

Would you know why my oil light flashes at second great take off ? 2008 Hyundai Sonata ?

Would this be the same on a 2013 elantra gt manual clutch

Did you reuse that transmission with the grooves in it I have the same issue right now

@joeybrazil3376

11 ай бұрын

Hey man I’ve got the same issue with my transmission. Nobody makes a repair kit. Did you overcome that issue? It’s not excessive grooving like in the video but it’s definitely enough to catch attention. Thank you👍🏼

@brianbuck1201

11 ай бұрын

@@joeybrazil3376 put new used tranny in

@ELCLAVE300

3 ай бұрын

I'm wondering the same thing.​@@joeybrazil3376

Is this the same layout as an 08?

I pulled the axles, made it easier. pulled upper wire harness across back of engine, made it easier. car on jack stands, then used hydraulic lift table for the subframe. unbolted the tranny to frame mount from the tranny, 4 bolts, instead of separating mount. allowed it to drop straight down with no interference on body frame. new/used unit had some light damage to the throw out bearing tube, was able smooth them out. How did you deal with the severe grooves???? Great video, thank you!

@user-hn1vr9gd7i

11 ай бұрын

Hi, reading your comment. Are you saying you where able to get the tranny out without removing the subframe this way?

@rss608

11 ай бұрын

no, removed the subframe first, then the tranny. My point was that it is easier to remove the tranny mount from the tranny.

@user-hn1vr9gd7i

11 ай бұрын

Thank you for clarification. Guess I hoped it would be. 😄

@rss608

11 ай бұрын

sub frame is pretty easy to remove... no big deal...

@ELCLAVE300

2 ай бұрын

I was wondering the same thing about the grooves. I have an 2008 Elantra and I hope that mine doesn't have any grooves.

I had my clutch replaced on my elantra now my shift knob is off center, more towards the right making it very hard to get into 5th gear...do you have any ideas how to fix this issue? Thanks in advance

@someyoungguy1923

3 жыл бұрын

Your shift cable bracket is likely misaligned. Or both cables may not be fully seating in the bracket on the trans

How many hours of labor did this take you? Just curious.

I was wondering how many miles on the car and if this was the first change. Thanks for the video!

@USSHammerology

9 ай бұрын

I have 120k on my Elantra and the clutch is still good.....

Almost got the tranny out on mine today

Damn is a typical clutch replacement this extensive.

@frankbenz893

3 жыл бұрын

I think the whole subframe drop makes it more extensive, but for transversal engines is a bit more extensive than longitudinal, generally speaking.

Oh man, what is this crime ?