Was just looking for a video on replacing an EMMC chip, and now I know how to mod my Nintendo! First, I’ll actually get around to replacing the chip on my laptop.

Sthetix = world's BEST chip man! 👍👍👍 You are incredible! Greetings from Germany!

@sthetixofficial

Жыл бұрын

thank you

@amazingretro7125

Жыл бұрын

I agree the best tutorial no segway

I freaking love you man. you are the best. beautiful clean precise work. love and respect from Germany.

@sthetixofficial

Жыл бұрын

thank you

@jayr6854

Жыл бұрын

Ein Volk ein Reich ein kommentarbereich Seit Jahren der beste der gutste hier ;D

@user-dn9kk9qu5y

Жыл бұрын

Hi from the UK I have a massive problem please help I need to refresh or reset a bga IC chip can you assist I want to wipe its memory so I can reuse it and if there's a way if performing this action without dissambly I would greatly appreciate it if you can answer this for me I will happily pay you £50 many thanks friend

@sthetixofficial

Жыл бұрын

you can just short the pins to reset the modchip

@user-dn9kk9qu5y

Жыл бұрын

@@sthetixofficial whats a mod chip

Thank you very much for this video. I'm dummy in eMMC and I got comprehensive infrmation about everything I need.

@sthetixofficial

5 ай бұрын

You are welcome!

this is genius level work .. wow

@sthetixofficial

Жыл бұрын

thank you

👏👏👏👏👏excelente video ingeniero muchas gracias, saludos desde PERÚ 🇵🇪.

@sthetixofficial

Жыл бұрын

you are welcome

its nice to watch, its so relaxing 😎

@sthetixofficial

Жыл бұрын

Thank you

That was nutty. Never seen a dat0 extension done that way.

@bigtitmaster

Жыл бұрын

because why would anyone risk taking off the chip just for that. but if you already have the chip off, then why not use the more solid one?

Fantastic work, as always. I just need to find the supplies you used to reball the EMMC. I found the stencil, just looking for the stand.

@HecTechFPV

Жыл бұрын

but tbh id just put down some paper towel , lay the stencil on top and do it by hand

Ty its so easy with the right Equipment. I will get the Reader/Writer device and try it by myself. Seems easy

This is nuts! Good kind of nuts! 😆

Hello there, why when you test the DAT0 point refer to 0.8V in which set do you put the multimeter and between which points you test the probe? thanks.

Fantastic....one question... is that possible to do the same procedure that you have done on dat 0 with the clk and cmd points on a switch lite? Using the points on emmc to jump to picofly....acidently i destroied the pads of the mother board

@sthetixofficial

Жыл бұрын

u can

Awesome work!!! Question: if it's possible to do all of that, then wouldn't it be possible to edit the data inside the chip to essentially put hekate/atmosphere in eMMC itself and avoid needing the entire mod chip altoghether?

@sthetixofficial

Жыл бұрын

not possible. it needs a modchip

@carb_rta

Жыл бұрын

unchipped switch would probably refuse to boot something unsigned

@falconmick

11 ай бұрын

A part of the boot up procedure of the CPU is that it checks the integrity of the software it is loading, the mod chip both tricks the CPU into loading the wrong boot file from your SD card AND glitches the CPU startup to skip over check

🥰you are so good

Keren..baru liat channel ini 👍

@sthetic exelente video, comk quisiera que tus videos tambien estuvieran en español para entenderlos al 100% porque aun se me complican algunas cosas, pero eres un exelente tecnico, saludos desde Ecuador.

@sthetixofficial

9 күн бұрын

Thank you, but I dont speak spanish.

@Blue164939

6 күн бұрын

@@sthetixofficial Tendras un video con una nintendo switch v1 y v2 como clonar una ENNC o se puede cambiar solo el modulo.

Hi, love your work and I recently accomplished this procedure on one of my OLEDs. You've mentioned that you can use magnet wire instead of the solder lugs. Do you know how thick that wire should be? I've used one with 0,1mm diameter and I've had a lot of trouble soldering the eMMC back on. I wonder if using 0,04mm diameter would have been better

@sthetixofficial

3 ай бұрын

hi, the 0.04mm will be fine.

Okay so you can find either emmc chip on the OLED model, are there specific regions that use only Samsung or is it some kind of lottery?

@sthetixofficial

Жыл бұрын

Either samsung or hynix is fine.. It only affects the installer not the end user And we cannot check if the console uses a. Specific brand. Unless we disassemble it

i have a same looking reballing kit from aliexpress like you with magnets and holder. I have the problem that the stencil plate is going up after heating. After the procedure i dont have perfect balls but much balls sold together :( you have maybe a tipp?

@marsimoon185

9 ай бұрын

lel, ok now it looks good, at the 4. try the stencil was in the middle perfect and not going up. looks good hehe

For the V1 and V2 models, are there like higher capacity NAND modules like at least 64GB or 128GB?

@sthetixofficial

Жыл бұрын

no it does not.

Hello, thanks for all your videos, and the HATS pack, everytime I do a modchip install, I use it... Just a question, what is the app that you use to calculate the time of the hot air? It would be very useful for me.

@sthetixofficial

7 ай бұрын

That is not a calculator, it is just a timer . It is called the Interval Timer, made by Julia Hollitsch . It is on the Play Store

@lucasdesouza7891

7 ай бұрын

@@sthetixofficial thanks, I knew it was not a calculator, I just did not know what to call it.

Can you give me a link for the full bga kit you showed in your part list with correct stencil for the switch OLED eMMC?

@sthetixofficial

Жыл бұрын

it is the amaoe emmc reballing kit.. available on aliexpress

Thsnks!

It is possible to use the system of another console to finish the image that is needed, greetings

AMAZING！do you think i can do the same for a BGA100 ? i got an SSD with one BGA chip cant be readed! ....therefore i cannot access any sector

@sthetixofficial

10 ай бұрын

maybe you can try doing that

Hello, what is the app you are using to guide yourself when you are soldering/desoldering the eMMCs ? Thanks !

@sthetixofficial

Жыл бұрын

I used a digital microscope and premier pro

@ThibaultAnd

Жыл бұрын

@@sthetixofficial Thank you for your reply ! I meant the Android app where the temperature and the timer (to guide you while using the hot air gun) was displayed, if you have the android app name it would be nice, thanks :)

@sthetixofficial

Жыл бұрын

I forgot the app. It is just a simple timer app on the play store

@ThibaultAnd

Жыл бұрын

@@sthetixofficial thanks !

Sthetix i have a question..... i have taken an EMMC backup with Hekate.... now the EMMC chip is bad and I cannot flash it with Hekate (I have done it once worked for some time and again became corrupt) it gives me error "EMMC SLOW MODE" and it cannot write the backup back to it... if i replace the Hynix with a Samsung one can i use Hekate to write the image back? Thank you!

@sthetixofficial

8 ай бұрын

you can.

Hello name application doe you use in vidéo for température cycles ? Thanks friends

@sthetixofficial

2 ай бұрын

it is just a timer, interval timer . it runs on android.

HI Very good work , the Amaoe eMMC BGA Stencil is with 0.15mm balls is it ok ? or should it be a 0.3mm stencil?

@sthetixofficial

11 ай бұрын

just use the amaoe stencil, it should be fine.

@MIRIVEDAN

11 ай бұрын

Thanks !

Hello! Can I do this service using the RT809h recorder?

@sthetixofficial

9 ай бұрын

Yes you can try using that tool too.

Any reason why you took down your video for rebuilding a corrupt nand? Was there any issues with it or is it still good to follow? Thanks

@sthetixofficial

Жыл бұрын

It is there bro The video title is unbrick

Hello friend, congratulations on a job well done, I'm trying to fix a multimedia that runs android system in which the defect is the emmc with corrupted data, I confirmed this by replacing the emmc with one from a working device, the device turned on normally, but when I make a clone of the good emmc and fix it in place, then the device does not boot, only the initial logo appears, could you help me to find out what I am doing wrong? thanks.

@sthetixofficial

Жыл бұрын

sorry i dont know about it. you need to ask xda dev to find it out

@gabrielcetera

Жыл бұрын

@@sthetixofficial ok, thanks to return...

Do consoles which get the emmc replaced this way still have access to official nintendo services without being banned?

@sthetixofficial

8 ай бұрын

yes as long as the console is not banned previously.

Is UFI BOX can resize partitions, to easier replacing eMMC on 256Gb? I'm watched your video «Installing the 256GB Nintendo Switch eMMC module» and i'm think it's to old for now.

@sthetixofficial

Жыл бұрын

yes you can.

@dispyre

Жыл бұрын

@@sthetixofficial can we wait updated video about increasing memory? 😉

@sthetixofficial

Жыл бұрын

I will make a new guide later

nice video thx

@sthetixofficial

11 ай бұрын

Thank you

another great video. Do you have a link to the jig you use? thanks

@sthetixofficial

Жыл бұрын

What jig? Thx

@sthetixofficial

Жыл бұрын

The emmc stencil? It is amaoe.emmc stencil, you can find it on aliexpress

@fixingmoddingbuilding

Жыл бұрын

@@sthetixofficial Yes thats the one, thanks

If I have a backup of nand memory, and the console suddenly crashed (nand died suddenly). Will I need a programmer to flash a new empty nand flash, or can I just upload my backup to the console directly through hekate after I install the memory on the board?

@sthetixofficial

Жыл бұрын

you can upload the backup to a new emmc chip, but i dont think you can do it using hekate. you must use a hardware programmer.

@elco1945

Жыл бұрын

@@sthetixofficial Thanks for the reply. Unfortunately, I don't have a programmer. And given its cost, I can't afford it.

is it possible to do this manipulation with the t48 or t56 programmer? would it be faster with the 2 programs I mentioned?

@sthetixofficial

Жыл бұрын

I am sorry i dont know what they are.But I have the RT809H and it is not capable of reading the Hynix chip.

@bavecabanjaban

Жыл бұрын

@@sthetixofficial thank you for your reply and thank you for your unforgettable sharing of information good job

@sthetixofficial

Жыл бұрын

you are welcome

Hi Sthetix ,after I reballing emmu and fly wire inside (likes sandwich) I get error code while playing. 2002-3538. Is that got problem with my emmc chip or I need to tear down and reflow again ?

@sthetixofficial

Жыл бұрын

Bad game probably?

@feifei4859

Жыл бұрын

@@sthetixofficial no open on any game ....no SD insert also. In ofw error code pop up and force you to shut down. After few time now my switch totally unable to turn on ....is it RIP already🤣

@sthetixofficial

Жыл бұрын

maybe it is something else. i dont know that error code too

My question may sound stupid, but if I buy an additional 32GB memory module for Switch V2 (original /OEM on AliExpress) then can I simply restore my NAND backup using Hetake instead of doing these so I can have a clone of my eMMC which can be replaced just by unplugging and plugging back. Thanks!

@sthetixofficial

5 ай бұрын

you can restore it by using Hekate - if you already have the nand backup

@HeiLangXiaoDuo

5 ай бұрын

Thank you! Have a wonderful day! :)

Can I use an inexpensive eMMC to SD adapter instead of the UFI Box? The UFI is expensive...

@sthetixofficial

Жыл бұрын

I think u can

would this work for upgrading windows tablet EMMCs as well? Or could i just leave it blank and install windows the traditional way after installation?

@sthetixofficial

Жыл бұрын

I think u can but we don't know how to resize the partitions later

Is there a way to know which switch ships with samsung and which one ships with SK HYNIX? I would like to end up with one that has the samsung EMMC

@sthetixofficial

7 ай бұрын

no we cannot determine it.

Hello, greetings, excellent video, my comment is about how to rebuild the memory since mine is damaged, I could not obtain the user area partition, specifically the system, I could only read 512mb

@sthetixofficial

2 ай бұрын

please do the level2 unbrick guide.

Apart from for installing modchips, what is the advantage of switching to a Samsung chip?

@nuhacell9970

Жыл бұрын

It last longer than SK

@torchedegg

10 ай бұрын

doesn't randomly corrupt on your ass

can you see the photos on computer when you copy that i mean you have the acces to photos n videos ?

@sthetixofficial

Жыл бұрын

I don't know what u mean by that

Are there known issues with the hwfly 5.0 and the SKHynix? I hava an oled and just ordered the modchip, I dont know which chip I have inside, but of I got the SKHynix can I do the install with the hwfly 5.0 without problems?

@sthetixofficial

Жыл бұрын

i think you can.

Nice work. Very clean and neat. Isnt 360C too much for the EMMC? I will be doing a 0DATA permanant mod and I'm afraid to go this hot.

@sthetixofficial

Жыл бұрын

360 is about 200 on my hot air rework station

@h.a.6790

Жыл бұрын

The problem is when you have less heat you may risk your other components because it will take you longer to melt the solder. I think someone on youtube already tested this, the less time you spend the least damage incurs.

@engelsgarde7317

Жыл бұрын

@@sthetixofficial In your Dat0 guide you heated the chip to 260 degrees. How much is that roughly? And how do you know that the temperature is so different.

@sthetixofficial

Жыл бұрын

about 200c, but i found that heating the dat0 is not an ultimate way to solve the issue. the emmc ball could break in half someday. the safest way is to just slip the dat0 without heating it but use the four anchors version.

@engelsgarde7317

Жыл бұрын

@@sthetixofficial I only found the adapter with 4 point anchors on aliexpress. And unfortunately it's not available in my region. Is there an alternative?

Can this tool recover data from Chromebook or EMMC laptop memory?

@sthetixofficial

Жыл бұрын

any emmc as long as it is healty enough to dump the data

So here I tried out of curiosity and to know if it was possible to dump a nand oled soldered on the pcb of a V1 switch with Hekate, it works, it lasts 4 hours lol, it's 1 hour in less than with the ufi box for those who don't have one and therefore for much less 😅 on the other hand with NxNandManager it did not work 🤷 a very interesting video that gave me the idea Thank you Sthetix next test with mmcblkNX adapter.. if I have time

@sthetixofficial

Жыл бұрын

We can dump the nand with the nxnandmanager, using the usb tool box. It took about 45 minutes to dump the whole nand.

@itechconsole

Жыл бұрын

@@sthetixofficial I tried with NxNandManager but when I wanted to select the BOOT0 drive I had an error message and therefore impossible to dump the partition, same thing with BOOT1 I may have made a mistake because you obviously succeeded

@sthetixofficial

Жыл бұрын

Dump the boot0 boot1 using hekate backup menu. Dump the rawnand using the hekate usb tool

@itechconsole

Жыл бұрын

@@sthetixofficial thanks for the solution I hadn't thought like that next time i will try

@DragonEdge10

11 ай бұрын

So are you saying that you took a v1 emmc module, took off the original emmc, resoldered the OLED emmc, and dumped that one?

Does the UFI work for emmc chips on smart tvs?

@sthetixofficial

Ай бұрын

it works universally

Clean work. If eMMC is damaged, will I get a reading on Multimeter? 0.5-0.8v? After installing Picoflly, it won't boot. it gives a light indication that eMMC is failed but I get 0.6v on the Multmeter?

@sthetixofficial

Жыл бұрын

i dont support picofly. even if the emmc damaged, you still get the reading.

@af6727

Жыл бұрын

@@sthetixofficial Thanks. Is there any pad I could measure to tell me if eMMC is intact? Or is removing it the only way?

@sthetixofficial

Жыл бұрын

did u reflow the emmc?

@af6727

Жыл бұрын

@@sthetixofficial Yes. The adaptor is fixed in place pretty good.I gradually heated the chip, 150C, 250C,350C. One minute each.

@af6727

Жыл бұрын

@@sthetixofficial please let me know

Are you able to do this and swap over a bigger emmc chip say 256GB?

@sthetixofficial

9 ай бұрын

you can but you need linux stuff for expanding the user partition later.

Could this be done by creating an emuMMC of the OFW then using hekate to write the OFW to the new sysMMC?

@sthetixofficial

Жыл бұрын

you can but why you want to dump the emummc and transfer it to the emmc?

@theunkownviolinist

Жыл бұрын

@@sthetixofficial I was thinking of upgrading the eMMC and was wondering if it was possible without a UFI box since they're pretty expensive. For someone who doesn't really do a lot of hardware mods, it's a steep price for something that might only get a single use.

@sthetixofficial

Жыл бұрын

upgrading the emmc is not easy. you need to alter the partition using ubuntu. i think i will make a new guide someday

do u need the ufi box? u cant just make a hekate backup, replace eemc, and restore backup?

@sthetixofficial

Жыл бұрын

ufi is to dump a rather damaged nand

Thank you but that tool is very expensive. Is there any other way to clone or transfer the data to the other emmc. Can it be done the same way of installing higher capacity emmc the way you did one before?

@serg9448

Жыл бұрын

you can transfer in hekate. backup and then restore. just do backup before heating chip

@sthetixofficial

Жыл бұрын

well, there are other emmc reader and writer and the price varies. If you do a lot of modding, you need this tool and see it as an investment.

@sthetixofficial

Жыл бұрын

and we can use a higher capacity emmc, stay tuned for the upcoming video

@user-xu7js6wu6d

8 ай бұрын

​@@serg9448And if, for example, I kill the eMCC by reflow, having the backup copy, what next steps should I do for the console to work?

@serg9448

8 ай бұрын

@@user-xu7js6wu6d in backup folder create restore folder, move all files there and restore in hekate

You are in another planet from that work. Can i ask about ufi box i want to order too Greece it will work with the program? The program need pay per month? Because is expensive can you send me a link where to buy from safe? And last can ufi box data recovery from dead phone?

@sthetixofficial

Жыл бұрын

actually there are many emmc reader and writer out there. the UFI is not a subscription type, once you buy it, it will work forever. You can recover the data only if the emmc chip is healthy enough or not 100% dead. i bought it locally but you can buy it on aliexpress.

So overall you mean that, if we are replacing new EMMC IC with older "DEAD" EMMC IC chip, and copy paste our all data, into old to new EMMC IC, then we are get back our all data without loosing any single files, like photo, video, bookmarks, open tab in the browsers, search history, coockies, save passwords, device's settings etc. ??

@sthetixofficial

4 ай бұрын

You can copy the eMMC content and move it to a replacement IC and your data will be intact.

Hey in a switch with the chip ,can you make a video showing how to boot stock with cfw disabled iI heard you can play online this way .if not possible let me know

@TheFlyingHernie

Жыл бұрын

It's fully possible....just boot into Hekate and select Sysnand (stock)

@sthetixofficial

Жыл бұрын

please open this link github.com/sthetix/HATS/blob/main/stock.png

@adnerayala3409

Жыл бұрын

@@sthetixofficial That work man thank you so much

Will this work for V2?

@sthetixofficial

4 ай бұрын

it does.

fucking nice video, thaks from Brasil

What should I do to avoid this issue. I'm about to install a chip next week 😢

@sthetixofficial

11 ай бұрын

just don't reflow the chip

Is that possible for the UFI box to repair corrupted emmc back ?

@ucantbeatme3019

Ай бұрын

hahaha so funny

This way to clone emmc. And is this two emmc data exactly the same? If do this Whether I can clone an exactly same phone and no data lose.. Include userdata app data account information Everything is same.?

@sthetixofficial

10 ай бұрын

clone means copy the data 1 : 1

@UnbTyu-vu7vb

10 ай бұрын

@@sthetixofficial why I use 9008 backup data partition and write another same model phone when I reboot it. System. Notice me Decryption failed continue use to. RESET FACTORY SETTINGS. CAN I do something just. Clone. My data partition no data lose? Use Qualcomm tool. Because. It tool.is.expensive.and difficult. Thanks

Bro ise ufi lite that comes with ufi box kit that is used for reading user data that 5 hours cut down to about 30 min to 50min

@sthetixofficial

Жыл бұрын

it depends on the settings too.

fantisc work, to me after reflowing the dat0 point the switch wont boot, with this ufi tool i can read the skhynix chip, even the switch not turning on ofw

@h.a.6790

Жыл бұрын

It's obvious you killed your eMMC. Even if the chip is readable using a tool, it doesn't mean it's 100% functional.

@user-xu7js6wu6d

8 ай бұрын

Stethix said in the comments that 360 degrees was not the temperature and that it was really 200 degrees that his hot gun threw 🤣 that's why the chip didn't die, but the other people who wanted to try by having different seasons ended up throwing more heat. Really , the heat also depends on how close or far they are pointing, but it seemed strange to me that it even said that using 400 degrees with SKHYNIX was crazy 🤣

Is there a way to tell if the console has Hynix or Samsung by SN or manufacture date?

@sthetixofficial

Жыл бұрын

we dont know

@elco1945

Жыл бұрын

@@sthetixofficial Which chip is preferable in your opinion, Hynix or Samsung?

@sthetixofficial

Жыл бұрын

samsung

@elco1945

Жыл бұрын

@@sthetixofficial Ok. 👍 Thanrs!

i would like to reciver tbe emmc data from a 10 years old phone, i might buy the tools and try but it seems not really easy and might risk breaking it

@sthetixofficial

Жыл бұрын

yes it is hard to do the operation.

Hi Sthetix, nice work. Just wondering if the SK hynix nand is the only brand that works with picofly/hwfly?

@sthetixofficial

Жыл бұрын

no, currently all kind of eMMC brand are supported.

@CodyRoseman

Жыл бұрын

@@sthetixofficial are all the nands bga153? or just the oled?

@sthetixofficial

Жыл бұрын

yes 153, all of them (for switch)

@CodyRoseman

Жыл бұрын

@@sthetixofficial Last question, can I use VFBGA package instead of a TFBGA?? I think its just a height difference

@sthetixofficial

Жыл бұрын

any 153 balls eMMC should work. but i think you better use Samsung brand as it is the best, fastest.

❤❤❤❤

Can you put links of the equipment in the description?

@sthetixofficial

Жыл бұрын

Amaoe eMMC BGA Stencil UFI Box Aoyue 986 BGA Rework Station Mechanic Soldering X XW5 Goot solder Wick Best Solder Lugs Leaded Solder Paste Relife RL 400 Amtech Flux NC 559 Sunshine Dual Brush SS022 B Tweezer IPA 99% Hakko FX951 Soldering Station Solder Mask Portable UV Lamp Qianli

Works it with a defect emmc Chip, too???

@sthetixofficial

Жыл бұрын

you can try reading a bad emmc with this tool

si tienes modchip por que no usar hekate para restaurar la emmc?

@sthetixofficial

6 ай бұрын

You can do that too bro.

hello sir on my console there is the problem with ufs ic so we clone it to the new ufs then fixed but the console is not turning on but i try to put back their old ufs ic still getting on but the new one is can’t we tried more than 2-3 ufs ic same issue any solution for this? my console is meta quest 2

@sthetixofficial

4 ай бұрын

maybe it is due to security matter. maybe your console sees the UFS ID and should match or it doesnt work.

@user-ox6hh1gt9s

4 ай бұрын

@@sthetixofficial oh ok sir so any other way to fix it?

@user-ox6hh1gt9s

4 ай бұрын

@@sthetixofficial our old ufs ic is (INAND SDINFDK4-128G) we clone it to (SKHynix - HN8T05BZGK) now i tried to connect with pc then show it qualcomm port in device manager

@sthetixofficial

4 ай бұрын

You better ask someone that is more expert than me. If the new chip is not working then there is something that blocks the process. Try to ask the phone / mobile device experts.

Can you upgrade switch memory to 128gb

@sthetixofficial

Жыл бұрын

256GB is the max, but it is not worth to have it, it is expensive

Is this for a bricked or failed emmc switch?

@sthetixofficial

Жыл бұрын

yes correct

Is it possible to replace emmc chip with ufs 3.1 on a laptop ?

@sthetixofficial

Жыл бұрын

no it is not possible

@antoniok4735

Жыл бұрын

@@sthetixofficial Thank you for the fast response.

can we replace it with bigger capacity?

@sthetixofficial

Жыл бұрын

u can but u need to adjust the user partition later. not easy to do

Hello sir how to full reset sk hynix ic from ufi box

@sthetixofficial

9 ай бұрын

I dont know. sorry

@Shah-Electronics

9 ай бұрын

Ok

try moding a sega mini 2s EMMC chip to 256 gb

Z3x or ufi box.and why thanks

@sthetixofficial

6 ай бұрын

i dont have Z3X, sorry

Cool. What about upgrading the memory? 5 fucking hours to read the chip... Have you tried to read the Samsung Chip after writing to see how long it takes? Maybe it's reading slow because the Skhynix chip is almost dead?

@sthetixofficial

2 ай бұрын

you can skip this process by getting the prodinfo data only and later rebuild a new nand from scratch using the level2 guide. that's faster than waiting for 5 hours

Where can you buy this box?

@sthetixofficial

Жыл бұрын

Aliexpress

Redmi note 4 dead phone recovery data?

I guess it would be the same if I replace and increase the memory of my S22 Ultra. That's what I'm looking for

@Gamersoft1124Pro

10 ай бұрын

that is not simple on the mobile phone, because the S22 ultra uses a UFS NAND flash chip, the UFS programmers are very expensive but if you have the programmer and the skills to BGA solder than the upgrade will be a success.

5 hours? Might as well go return the Switch and hope you get a Samsung eMMC on the swap out

@user-tq5ru8kk1x

Жыл бұрын

This will be useful in the future when Nintendo ends its support for the Switch

Exist something cheaper then the 300$ UFi Box ?

@sthetixofficial

Жыл бұрын

there are other tools but this ufi box is the best.

Hello. What's the BGA for that stencil? Thanks!

@sthetixofficial

Жыл бұрын

eMMC BGA stencil, from Amaoe

@af6727

Жыл бұрын

@@sthetixofficial You know you're the real deal right?

@sthetixofficial

Жыл бұрын

👍

@af6727

Жыл бұрын

@@sthetixofficial I'm getting one of these stencils. Do you recommend something better has come out? Thank you my brother.

@sthetixofficial

Жыл бұрын

@af6727 there are several stencils but the one I used is the best

bang buka jasa upgrade emmc gak ? laptopku pake emmc sandisk 32 GB cuma diisi windows free nya cuma 8 gb, pengen upgrade ke 64 gb / 128gb kalok bisa

@sthetixofficial

6 ай бұрын

tidak gan.

2 questions... Why not write the entire Emmc dump back to the replacement chip ? And can you replace an emmc chip with a larger capacity without having to edit the firmware ?

@sthetixofficial

Жыл бұрын

I did write the dump file entirely 1 : 1 and we can replace it with a higher capacity emmc

@MessalineApghar

Жыл бұрын

@@sthetixofficial thanks. I mist have missed it.. i thought you only did 3 segments with the checkboxes. My mistake .

@sthetixofficial

Жыл бұрын

Yes 3 segments only. The boot1 boot1 and the userarea That is enough to boot the console

@EXOGAMESPUEBLA

Жыл бұрын

@@sthetixofficial Can I use a Nintendo switch erista for dump and write EMMC of Nintendo switch Oled?

@sthetixofficial

Жыл бұрын

No way

Can it upgrade the chip from 64 to 128 or 256?

@sthetixofficial

Жыл бұрын

you can but not using this tool, you need to use linux to expand the user partition

@gembur3

Жыл бұрын

ultimate switch with 1tb internal storage KEKW

@sthetixofficial

Жыл бұрын

there is no 1TB emmc chip.

Link for stencil ? Pleas ?

@sthetixofficial

Жыл бұрын

Amaoe emmc stencilsRp 92,546 26%OFF | Amaoe EMMC EMCP UFS BGA Reballing Stencil for BGA153 BGA162 BGA169 BGA186 BGA221 BGA254 0.15mm Reballing Jig Platform a.aliexpress.com/_mMnIL5c

@alexpassions

Жыл бұрын

@@sthetixofficial thanks

where do you buy nands?

@sthetixofficial

Жыл бұрын

on aliexpress

@light3267

Жыл бұрын

@@sthetixofficial you got a link or what keywords do i search on aliexpress exactly? thank you!

@MessalineApghar

Жыл бұрын

@@light3267 I literally saw them on aliexpress , popped up on my feed without even searching

kalau boleh tau kelebihan pake chip Samsung apa bang?

@sthetixofficial

Жыл бұрын

Relatif lebih stabil dan lebih cepat proses boot nya (bila dari keadaan mati)

@NorolPlays

10 ай бұрын

wah kmu dr indonesia ya? aku sgka dari Phillipines selama ini@@sthetixofficial

@sthetixofficial

10 ай бұрын

yup dari Indonesia

try 3ds cfw video plz

@sthetixofficial

Жыл бұрын

Soon

Sthetix. I would like you to mod my oled. How can I reach you so I can mail you my oled?

@sthetixofficial

Жыл бұрын

hello although I can install the chip but FYI, i am in Indonesia. I think it is better to find someone near your place to save the cost.

@Dwayneff

Жыл бұрын

@@sthetixofficial that is fine. I am in no hurry. I don't know anyone locally or in the US to install the chip.

@sthetixofficial

Жыл бұрын

Try modzvilleusa.

@sthetixofficial

Жыл бұрын

Or u can buy a brand new oled from my online store

@Dwayneff

Жыл бұрын

@@sthetixofficial thanks. Forgot about modville. I reached out to him.

Can you tutor someone ??

@sthetixofficial

Жыл бұрын

this guide is the tutor

Link Aliexpress stencil reballing nand?

@sthetixofficial

4 ай бұрын

it is the amaoe emmc stencil, try to use that keyword

@speed_gamesss

4 ай бұрын

@@sthetixofficial I was doing the unlocking with kamikaze but the 6⁰ console I killed 2 trails

@speed_gamesss

4 ай бұрын

@@sthetixofficial Doing it by removing the nand would be a good option, correct?

@sthetixofficial

4 ай бұрын

yes. but u need to remove the cpu too I guess

@speed_gamesss

4 ай бұрын

@@sthetixofficial To remove the nand and solder it to the dat0 without using an adapter, do I need to remove the CPU?

great videos!! but one question on this video. was that a F word?? 9:40 it was a long fucken 5 hours!!

@sthetixofficial

3 ай бұрын

yes it was time consuming.