LOOL play sandstorm on them

@christianjackson

5 жыл бұрын

If I buy the PK rig I’m looking at then most definitely YES

@neemyn407

5 жыл бұрын

10 hour set of Sandstorm

@6884

5 жыл бұрын

🤦

@jayerwahlgren4735

5 жыл бұрын

Sandstorm is by Darude

@6884

5 жыл бұрын

yes

My 5cents as an electronics technician/electronics designer: * When reattaching self tapping screws to plastic, always rotate the screw slowly anti clockwise until you feel that screw to drop back to its original threads and then, with veeery little force try to turn it clock wise and see if it'll seat back to it's original thread (it should), if you dont' do this, you can mess up the threads by creating new ones. * When cleaning electronics, you want to avoid nylon brushes and microfibre cloths, they easily create static electricity and that can zap the components and break them or cause intermittent faults that can be hard to fix or trace down. Use normal kitchen towel paper and ESD safe brushes that one can find from ebay with few dollars. * Be very, VERY careful with the laser and the laser head mechanics and the motor. The laser head ways need to be lubricated after cleaning with proper lube (type of which I can't remember from the top of my head, but it's not very lean, it's more like thin grease than liquid meant for plastics). the laser lens itself should never see any alcohol or other solvents unless you're sure there are no plastic parts within that mechanism (which there usually is). Isopropyl alcohol attacks some plastics quite aggressively. Motor assembly shouldn't see any alcohol or other solvents (no, not even water) since the mechanism will lose the lubrication and it'll break prematurely and it's horribly difficult to lubricate... can be done but it's not easiest thing to take apart :D * Be careful with any remaining solvents on the boards, they can start to ingress moisture over time or attack plastics and rubber components. Thus isopropyl alcohol is recommended since it'll evaporate very quickly and thoroughly.

@djstretchtone9851

2 жыл бұрын

Great info. What's the best case scenario for cleaning the jog wheels and the top of a Pioneer Xdj Rx 3 DJ controller? Some of the plastic is shiny polished like and some not.

@chriztphr3650

Жыл бұрын

Good info, now I know my laptop screws are fucked

Gloves for safety (not wearing gloves in any of the video)

@skaterzero07

5 жыл бұрын

😂 yo fr wtf

@ryanquinn1257

5 жыл бұрын

risk. assessment. hahah

@bart3916

5 жыл бұрын

ESD gloves would be nice yes haha

Its hilarious how the video is made up like a tutorial as if anybody would ever do the same thing 😂

@theUtubemaestro1

5 жыл бұрын

Agree! You can try half of it! Taking stuff apart is easy, it's putting it back together that makes it unrealistic 🤣

@ColeRees

5 жыл бұрын

I once took apart my cdj700 to fix my tempo fader... 3 years later it is still on a shelf in pieces tucked away

@alimmi9

5 жыл бұрын

Well, some CDJs will have to go there every year..

@e.emerald3224

5 жыл бұрын

the last show I produced the fog machines got out of hand. I will be cleaning my nexus gear. It is not unthinkable.... and he got you to watch and get him tube credit $$$

@ryse_zink5756

5 жыл бұрын

MrJoe000097 now u have put this comment someone else is gonna do it it’s gonna become a trend

Where's part 2 of the video showing the Doctors cleaning out the lungs of the people who used the CDJs?

"dust is just boneless rock"

@josephstalin8442

4 жыл бұрын

Grant Fields that makes snow boneless ice

@j_o_s_e_g_a_m_b_o_a8889

4 жыл бұрын

@@djstilb239 damn bro got the whole squad laughing

@joebates4160

4 жыл бұрын

SQUIRREL_ WAX 😂😂😂

@CamGold

4 жыл бұрын

Cue the boneless pizza meme or cue Steve Aoki, Chris Lake & Tujamo - Boneless

@dennisstilb3868

2 жыл бұрын

@@j_o_s_e_g_a_m_b_o_a8889 what was my comment lol

I am a product demonstrator for Pioneer DJ. You are awesome for this video! It's helpful for even just maintenance cleaning.

Should’ve put them into diagnostic mode to test all the buttons and functions. Hold memory and tempo +3/6/10 when powering on, then scroll through menu with back/tag button. I’m sure you already knew this, but just in case 🙃

@dubb9020

5 жыл бұрын

do all cdj have this mode?

@dsquareddan

5 жыл бұрын

du Bb I’ve only been able to test it on cdj-2000 models. Regular, Nexus & NXS2. Not sure about 900 or any other model. I’m assuming there is some kind of button combination to get into a menu similar

@garyhost354

2 жыл бұрын

Love your VJ loops

This caused me so much anxiety watching him rip it apart lol. I'd never get all that back together 😂

@majorswitch8117

Жыл бұрын

Me too but thencagain its hire stock lucky dude he must have loads of cdjs just like sitting ghere casually

should have sold them on ebay "barely used"

@christianjackson

5 жыл бұрын

Maybe I did

Nice... love the video, our company has about 12 cdjs nxs and does take about a day or two to clean them all

Haha its usually another kind of white dust that needs cleaning out.

@Appletechweb

4 жыл бұрын

😂😂😂😂

Used to clean units that were smoke and fire damaged. A commercial dishwasher does wonders on most of the parts for the pre wash step. Do not use the dry cycle as the heat can damage plastic. Air dry with the alcohol only on the PCB's. Some silkscreen is damaged by the solvent. Odor permeates plastic so this does not apply to the dust, but Smoke X removes smoke odor.

This video is pretty cool, i might clean mine too after watching this!

You're insane!!!! Congrats on the amazing cleaning/restoring to former glory work on these!!

Thank you for posting this!

4:52 Him shaking that PCB viciously with one hand while standing over a concrete surface was honestly terrifying.

OMG !!! 😳 Thanks for sharing man!

Always top notch videos!

Really interesting video man! love it.

That's a process and a half but DAMN the before and after is awesome

MA BOI IS ALIVE welcome back ❤️

The smiling face on the display is the cutest. Fave moment, tbh.

Nice vid! We clean them with the same method when dealing with dust. If they come back sticky from liquids we use Multifoam just spraying it on the cdj let it do its job for 1 minute and then take it of with a soft towel. And respect for you (even with cdj’s from someone else) to send them to Burning Man!

Pls Do more of these tech videos!! They are so awesome and interesting to watch!

Thanks for the video man i appreciate it

i literally just said to myself yesterday that i needed to check if you had posted a video recently, as I hadn;t gotten a notification in what seemed like forever!

It blows my mind that you were able to put this back together. Props to you for knowing your shit

great to see you again!

Wow at the beginning the Dj Equipment looks like Mad Max Stuff🙀 Cool Video 👍

I know that I will never need this tutorial in my life, but for some reason, I find this video satisfying)

Very interesting, great upload!

Awesome video man!

This video made me extremely nervous 😂 good that you got your CDJ's cleaned 👍🏻

Cleaning/Restoring Videos are way to satisfying

I had to do this to a 2000NXS that had been soaked in beer! That stuff gets to places you wouldn't believe! 2 hours later it was spotless and running! A tip for engineers - I Never buy cans of spray air, instead I use a large airbed pump with a long pipe! £20 and lasts for years. I Really enjoyed thgis video, it's always good to see new tips and tricks explained so clearly. Bravo!

@Co-km6cl

Жыл бұрын

What about an oil free air compressor

@nickbenke3306

Жыл бұрын

@@Co-km6cl They will cost Way more than £20!

More cdj repair video’s please, they’re so entertaining

awesome video man!!

Amazing video!

Ive done this with cdj 1000 mk3s before! :) Great vid!

Awsome video tnx man

Eyyyy you're back

I took two CDJ-900NXS and a Xone:92 mixer to Spain from California in a pelican air case (no charge for weight or size) as a checked back through 4 airports and there and back. No issues.

0:26 HEART ATTACK!!!

I have been building custom guitars since the 1980s. When we began using CNC machines, the wood dust was just killing em.... What worked great was to run a low pressure (25 - 35psi) regulated filtered through desiccant air line from the shops air compressor .. basically it was like a little clear hose like paramedics use with a oxygen mask.. Dust simply can NOT enter due to being slightly pressurized, or more like, dust cant swim up stream... I'm sure you would have to drill a small hole to feed the air... Same goes for your rack... You can run K&N off road filters in front of the rack fans, but also push compressed air into each rack unit ... The dust in the wood mill might not be micro rocks, but it's like peas & carrots with static, LOL!... And honestly, I don't know how anyone can even think of being at that place without a compressor to blow your face , your hair, hat & clothes, 8 track tapes, etc. Oh, and you can charge money to put the hose in your shoes , omg it feels good, LOL!.. Hope this

Great job Christian you are a very intelligent guy!

bruh its so satisfying to watch

good video the 2000 nexus have i self, thank for the nice video!

Interesting, I learned a lot. Sweet video👍

Looks absolutely dope with all the sand

Awesome!

My man is back

AWESOME video!!

Oh look who decided to upload

@RadINation

5 жыл бұрын

I know your probably joking but it can be hard to juggle ones job or jobs, video/editing and most important family and maintain a steady upload to youtube.

@eduardojvivas

5 жыл бұрын

Yea no means of bashing. I respect the time christian puts on each video for quality purpose. Much love

Nicely done

so good... thanks!

Nice work dude 👌🏻

What kind of ip rating lighting fixtures would you recommend for an event like burning man

$40 for two PLASTIC buttons?!

@anthonymuccillo

5 жыл бұрын

lol, no shit. you gotta be some kind obsessive nutbar to pay that. I'm assuming hes pulling prices from pioneer directly which are ludicrously high. They quoted me $40 for a $5 relay and i needed 14 of them...

@christianjackson

5 жыл бұрын

Well it's a little difficult to get the injection molded plastic parts from anywhere other than pioneer lol. I get all my tact switches directly from electronics component suppliers/wholesalers.

@christianjackson

5 жыл бұрын

Cheapest they are on ebay is about $40

@Maxwaehrens

4 жыл бұрын

@@kryzkat8762 it costs Pioneer less than $1 to produce those buttons.

@gelatinous6915

4 жыл бұрын

Two mechanical switches, two LEDs, an LED microcontroller, wiring, and of course Pioneer tax

insane result!

This was honestly very interesting

Very good video!!!

YAY A NEW VIDEO!

Dude i Love your videos especially your tutorials i've taken so much from them. Because of those videos I was invited to a 2000 guest party to do the lighting (btw I am 16)

That was dope!

4:19 I didn’t learn that in 7th grade science class

@PneumaticFrog

5 жыл бұрын

that's basic pH science

The music at 2:50 is Some Air (slct Remix) - Gloria tells Ironic i would say :D

Your amazing. I cant believe you cleaned them. WOW. I still have clothes with dust from burning man 4 years ago. DO you have any videos where you fix USB port?

Rent them with the extra insurance next time. Great vid! Glad your back

This was an amazing vid

hi chris, you think is it worth or ok to clean or sprayed using contact cleaner (or else) the PlayCue and Headphone Cue buttons before deciding to replace it? sometimes those are stuck. second thing is: My DJM Right channel signal on master are leaked all across 4 channels. all LEDs (meters, cues, color fx) are blinked when the balance set to center. But it’s normal when its set all the way left. need your technical advise 🙏🏻

Detailing DJ gear i like it.

Thank you bro

Best to vacuum it first, the can air will blow more dust into places it couldn't normally get into.

@dougharper1492

5 жыл бұрын

Slinky Trips lol, so youd prefer to risk vacuuming a screw or something important? Whenever you decide to use the vacuum method, let me know how it goes.

@steelbluesleepR

5 жыл бұрын

@@dougharper1492 you know things that go into a vacuum cleaner aren't gone forever, right?

@dougharper1492

5 жыл бұрын

@@steelbluesleepR so have you made you youtube vacuum cdjs video yet? Let me know how that goes

@steelbluesleepR

5 жыл бұрын

@@dougharper1492 no, but my job is to clean and maintain high end camera equipment. I use a small vacuum quite often.

@echno4727

4 жыл бұрын

@Jonathan Prasad Just about to write the same thing.

Microscopic rocks, so let's draw a smiley face on the screen.

you are a mad man, gj

NEW CJ VIDEO POGGERS

Lovely job

Have you looked into "board wash" @ your favorite electronics supply. Could save you the wash and rinse with so much water (iso. has high water content), and it is designed for safely washing boards and components.

holy shit! I always wondered if there is a place you can get these things serviced for you, I hate taking things apart like that.

I bet this guy is in the minority of people that go to these lengths to clean their equipment after Burning Man. Amazing job!

Christian Jackson!! What’s up man!!!

Those air cans are expansive for what they are. I go to the local asda forecourt to the tire inflating hose and blow out my computer every 6 months. Does It the world of good. And the plums of dust that come from It Is amazing. Now the young lad In the shop tells Me that since I have been doing It more are doing It started a trend. lol. Nice fix good Video. PS Put some teeth picks In the fan blades before doing this to stop them moving. I do my disco amps that way as well.

Good job! Regards!

Very Nice Video !!!!!!!!!

Hey I'm 18, from New Zealand and im really into lighting. I was wondering if there were any free lighting software's where I can learn abit about how desks work (like MA on pc)

Christian, how do you clean the LCD screen? Thanks! I watch your video a bunch

0:27 as soon as this frame came up i squealed

you can make everything by the way lov your vids

Gotta make a bubble boy container for the cdjs lol

LOL...I was just sent a defective CDJ in the mail. Time to be Mr. Fix It. Thank you for the video.

You're cool! I'm not sure if i do that the cdj working again or maybe more broken 😅

Antistatic Foam cleaner is good for electronics. It completely evaporated and doesn’t turn to water to drip into crevices that might damage circuitry

Good video. Want a pair of Pioneer 2000's now if they can handle that type of environment & be able to be shined up to play again.

It's so satisfying to watch something really dusty get cleaned, but at the same time, I hate cleaning.

I really love these CDJ repair videos of yours! I would really love to one day acquire a CDJ setup but buying it is way too expensive. I’m relatively handy with electronics though and buying broken ones and repairing them seems like a great option!

@christianjackson

5 жыл бұрын

I did that with some “for parts” units on eBay. Really easy to fix usually

@bjornssondj

5 жыл бұрын

Sounds great! Got any good resources for CDJ/DJM repair? Any good sites/forums/youtube channels? aside from this one of course :)

@christianjackson

5 жыл бұрын

Honestly I’d say just look into general electronics repair. Louis rossmann on KZread is where I learned to solder and troubleshoot electronics.

@bjornssondj

5 жыл бұрын

All right thanks man!

@2:53. Hahaha!!!!!!!!!!!!! Dude, you're hilarious! I hate to say it, but I'd have been tempted to just round file them all. What a mess!!!

Love the shoes 😂😂

Didn’t know about the water/vinegar and alcohol trick. Will be useful for other electronics

Hey, Can you please tell me what Peli Cases are you using for the 2000 nexus? I simply hate the normal flightcases (plus they are not waterproof). I just need the model to see if I can source it where I am. thanks a bunch