Chrysler 200 Throttle Body Replacement
Автокөліктер мен көлік құралдары
This is a 2012 Chrysler 200 that wouldn't start due to a faulty throttle body.
Amazon Links:
Throttle Body amzn.to/3Y2ZC5v
Hub Buster: amzn.to/3sXGBU5
My test light: amzn.to/2VCYpak
My scan tool: amzn.to/3JCxrD2
My little scan tool: amzn.to/3H2bWtt
TPMS scan tool: amzn.to/35aYLJN
Tire Machines: amzn.to/2R4mYu6
Torx Socket Set: amzn.to/3By4pSa
Torque Wrench: amzn.to/3scOMg9
Bench Vice: amzn.to/3sTtDXf
Plastic trim tool set: amzn.to/3v3Xy1t
LED magnetic light: amzn.to/3p1q00t
MUST HAVE for coolant work https: amzn.to/3oYinI8
Пікірлер: 31
You were so much help. I’m a single mom and I always go to KZread to learn how to fix my car. Your video was the best I’ve seen yet.
@Tomsfoolery.
4 ай бұрын
Glad I could help!
@habebs7345
Ай бұрын
So did you do a relearn on yourself
Next time (for the video)-- just take a few minutes and cut open the old one with a cutting wheel, and you will typically find that the little plastic gears are broken on the inside. There's an electric motor with a small gear (sometimes it's a worm gear)-- and then there's a long sweeping gear that connects to the butterfly shaft-- and that will typically break off a tooth or crack in a few places, because of it having to overcome the sticky gunk in the throttle body. The cheaper brands tend to break for no apparent reason, just from heat cycles on the cheap plastic. For the OEM's, it usually takes a really gunked up butterfly getting stuck, or even getting frozen or iced over, etc.. Cutting them open would make for great 'bonus content. You can usually learn a lot just by taking a peak inside; there's nearly always something very obvious inside.
Love it man.. thank you
Super easy explanation. Thank you. Going to replace mine myself.
Thank you sir! I was worried about paying over $500 when I can just do it myself! SUBCRIBE!
@Tomsfoolery.
Жыл бұрын
Thanks for the sub!
This video helped me for my car so much. 😊
@Tomsfoolery.
9 ай бұрын
Glad it helped!
THANK YOU SIR!!!
Good job buddy you really are a good mechanic 🧰
@Tomsfoolery.
3 ай бұрын
Thanks, I try!
Great video
@Tomsfoolery.
Жыл бұрын
Thanks!
I'm going to get me some drills and work on things my self. Ty and I may replace my throttle
@ChamillionAccounts
7 күн бұрын
You do not need drills. Just a socket set will be enough to fix most anything on a car.
I have 2015 with same light on do I need to program it or just reset the gas pedal reset
Good video 👍 👍
@Tomsfoolery.
Жыл бұрын
Thank you
Need help because somebody put different connector for throttle body and buy but the connector is same like you show video but I'm not how conect wires
Enay has some inexpensive 👍
What if I don't do a relearn
Hello! I have a 2013 Chrysler 200 that currently has the throttle light on the dash. I just finished replacing the ETB and ran it for any codes but it still won’t start. I also checked for a weak battery and no sign of anything. Any help or suggestions are appreciated!
@Nikeape92
4 ай бұрын
Check the alternator
Do you have video taking it off?
Oh please help me!!! I am replacing my throttle body tomorrow 2/5/23…. I got the new part in the mail. (I didn’t go to local store) when I tip the ETB with the gears down. There’s a noise like a pin dropping against the plate. Is this normal with the throttle body? Also, is there a manual relearn procedure for us who don’t have a scanner like yours? I looked into my obd2 and it doesn’t offer the relearn for ETB.. please help. I’m also thinking, if I disconnect the negative cable, does that bypass the relearn procedures? Thanks in advance!
@Just_Tyler360
Жыл бұрын
I’ve added a video to show you. Here’s the link. Again, thank you for any information you can provide. I’ve never done a job like this before….. kzread.infoPHje1_JKgl4?feature=share
@calholli
Жыл бұрын
It will usually relearn on it's own as you drive it a few times.
@Tomsfoolery.
Жыл бұрын
Sorry for the late response. Did you get it sorted out?