U should put some piece of rubber between the bed and tailgate and just run it under the bed liner so when u dump the items flow out good and dont fill that gap

@FcDominick

6 ай бұрын

I have thick rubber roofing I thought about using for that. But with out the factory bumper a lot of things that fit don’t stay in.

OK, maybe get a piece of conveyor belt to go under the back end of the bed liner screwed to the metal and over the tailgate liner to bridge the gap, so your load doesn't get hung up!👌👍🙋 You could also build a scissor lift mechanism underneath so you don't have to have the crane part sticking up so high.

@FcDominick

6 ай бұрын

Probably gonna use some rubber roofing Mayer for something like that

I had just seen u built ur Dump Trailer video. works and look COOL.. Congrats Young Man..

@FcDominick

5 күн бұрын

Thanks. I should have another video out soon. Been moving a lot of material with it

weld a square tube in midle going down a foot or 2 and hook ur hook to it so it brings the bed up higher

@steverone7623

6 ай бұрын

This here is the way to go

Great job, i would instal some guides so when you put heavy load it doesnt go to sides and break your hinges.

Thinking the mass dont look good or right at all think u build a lift mechanism like in a dump truck & pull back witch would lift the bed & wouldn't have all that in the air but the rest come out nice

Muchas Felicidades Joven Por Su Canal. Saludos Cordiales Desde Mazatlán, Sinaloa, México. ..

thank you for showing the build out . made my day ... aloha

Great intro😆

Great job that will be very Handy!

The trailer looks awesome, can I ask you why you used a winch and not a hydraulic cylinder? Wouldn’t cost more…

@FcDominick

Ай бұрын

Much cheaper. once you start making lines and fitting cost are up there now. Hydro Pumps are like $600 and then either building or buying a scissor style lift would be very expensive. I would have to find a used one somewhere. The other option would be a tall telescoping cylinder which would also be in the $700-$800 range. I may build another one where the mast extends so it’s not so tall going down the road.

@derkompressorschrauber

Ай бұрын

@@FcDominick thanks for the Answer! I just convert a small trailer to a dump trailer and put a hydraulic inside , with a Hand pump inside everything costs about 400$, I’m upgrading it with a 2nd pump operated by a cordless drill so I don’t have to do it by hand. Maybe it’s a idea for your next project? Check it out 😄 DIY Kipper Akkuschrauber Pumpe erster Test , DIY Dumptrailer Cordless Drill Pump first Test ! kzread.infou0mga_fE4-I?feature=share

I liked it and you could up grade it to a self contained hydraulic set up. You could put one to gather it wouldn't have to be new stuff you can find a lot of it you can rebuild if the price is right that would save a lot of $$$$. I also subed.

genius 👏

I prefer a short mast with scissor hinge underneath, winch cable rides on pulley and picks body up to around 30 degrees then the winch starts pulling on the scissor hinge rest of the way. What winch did you use?

@FcDominick

Ай бұрын

Harbor freight 9k

I have a 70s c10 long bed I saved for this application and never finished it. I also have a Kioti CK2610 how you like yours? I found a dump bed that fits my 3500hd but think 2 yards or 3 yards top and will cost me $1800 delivered or I can finish my C10 dump trailer. Cool video.

@FcDominick

3 ай бұрын

Mines not much different 2620. It’s good. Haven’t had it long. It’s a strong machine for its size. Sometimes I wish I hade more lift. I would do the trailer. Modifying your truck like that in some areas they might think your commercial

That’s pretty cool. I may have to build one myself.

@FcDominick

4 ай бұрын

Pretty handy if you don’t need to haul tons

@tri5garage544

4 ай бұрын

@@FcDominick I’m thinking about building something similar to use for cleaning up my property, hauling scrap or making dump runs.

@FcDominick

4 ай бұрын

@@tri5garage544 exactly my plan. Super handy for the time it’s been built. Registration should be here in a few weeks.

@SgtRudySmithbRet

4 ай бұрын

How much do you think it will "safely" haul? ​@@FcDominick

@FcDominick

4 ай бұрын

@@SgtRudySmithbRet suspension will hold more than 2200 pounds from experience before riding on the bump stops. It’s pretty heavy duty weight 2200 empty. I think gross 6-6500 is possible. So 4k payload

excellent excellent work my dude, i wish you can make me one out of a 2024 silverado dually bed to match my truck ..... ID PAY YOU MONIES for one

What is your total cost of supplies, minus donor truck? I was actually getting ready to build a similar setup, but I didn't want to buy the $4000 Hydraulic ram kit for the lifting set up.

@FcDominick

6 ай бұрын

I priced the hydraulics to be $1500 minus any fittings and hoses. And however many trips to the hydraulic shop. The juice brake hitch/ coupler was $450. Roughly $600 in steel. But the angle iron I bought for another project. Winch was $300. $75 for the pulley. I had no hardware for brakes so that was $250 or so. Most other things I had already. I would say I did it for $1500- definitely not more than $1800.

How tall of a master did u need for that dump angle?

@FcDominick

Ай бұрын

I think I’m right at 12 ft from the ground.

Need a redbull sponsorship after this

@FcDominick

6 ай бұрын

I wish

Great idea and video. What year is your Studebaker truck?

@FcDominick

6 күн бұрын

Thanks, 1951. The full build is on the channel from a few years back.

@LastMinuteGarage

2 күн бұрын

@@FcDominick I'll check it out. My build is stalled right now but I'm doing a Studebaker Explorer frame swap. I love the look of those trucks.

@FcDominick

Күн бұрын

@@LastMinuteGarage full explorer drivetrain?

@LastMinuteGarage

15 сағат бұрын

@@FcDominick Yes. 5.0 V8 AWD which also has 4 wheel disk brakes, and an 8.8 limited slip rear diff. I hope to resume the project early next year.

You could gain some angle adding a downward extension where your d ring is on bed

@FcDominick

5 ай бұрын

I might do that and leave the other one as well. Compare height vs dump angle. Say 8 inch extension forward. I think it would gain angle but loose overall height.

@loganpark7993

5 ай бұрын

Just straight down was more my thought. If it extends below the hinge it will be closer at the top and get more height

@FcDominick

5 ай бұрын

@@loganpark7993 the pulling power is the strongest when the rope is more parallel. So further out would correct that. Down might help more height but would have same or less pulling power up

@loganpark7993

5 ай бұрын

@@FcDominick yep and the further straight down you go below the hinge to closer to vertical it will be at the top

Hi, good idea! What about registration of trailer?

@FcDominick

3 ай бұрын

I got it registered and titles. State issued vin. That video is about half way finished.

@Maxxximma

3 ай бұрын

Is it difficult process?

@FcDominick

3 ай бұрын

@@Maxxximma not here. I didn’t have to do anything other than drop it off for inspection and cut a check.

@Maxxximma

3 ай бұрын

Ok, thanks

or just set it to ur tongue it will give u little more in pulling up

Use the winch on a sizzor lift hinge under the box n get rid of that hideous looking hoist u built

I like it but all that work and you clearly have the skills... why not a hydraulic ram instead of the winch setup?

@FcDominick

6 ай бұрын

Cheapest ram set up new would be roughly 12-1400 more plus time and labor getting lines made

@hurtinalbertan3844

6 ай бұрын

@@FcDominick fair enough, money is always a factor. I probably would've saved some money on replacing all the brakes and spent it on the ram instead, but nonetheless great job!

@FcDominick

6 ай бұрын

@@hurtinalbertan3844 I had 0 brakes or hardware. It was all removed when I got the truck. Was really set on hydraulic brakes. I’d think a mast the raised and lowered would be an upgrade I’d explore further first

@hurtinalbertan3844

6 ай бұрын

@@FcDominick the actual truck should be able to handle 3000-4000 lbs without trailer brakes, the trailer itself maybe weighs ~1000lbs, how much weight do you plan on hauling with it? Or even I know around here in Canada you can get whole rear axles from pick n pull for $180, it's probably even cheaper in the state if that's where you're from. Not bashing your design or anything, that's just the route I would've went

@hurtinalbertan3844

6 ай бұрын

@@FcDominick I did a quick google search and depending on your area, trailer brakes are required when the trailer "laden weight" is 2000lbs OR more than half of the tow vehicle weight. But you do need breakaway brakes for any trailer over 2000lbs. Just fun facts in case anyone was wondering lol

Hopefully the break light wires will keep it from sliding across the intersection 😅😅

Nice 😎💯🦾🦾

u will need to cut the back of the tongue a little

You are going to put thousands of pounds in that thing and the main attachment is hinges 😅😅

@FcDominick

5 ай бұрын

Yes is needs hinges to dump.