Thanks Dave, for your accurate directions. It is done !

gracias por el video...excelente... me ayudó a reparar mi ECHO.... desde Acapulco, México...¡

Thanks! My brother gave me his CC-301, which is basically the same saw, and it runs great. I broke the primer bulb this morning, so this tutorial is really helpful - thanks again!

Very well done with excellent photography, and precise easy to understand instructions.I knew all this information, but it was still a pleasure seeing your tutorial. Thank you.

Thank you.

@DoItWithDave

3 жыл бұрын

Thanks for watching!

Thanks. this is exactly what I was looking for. replace bulb on C8-305 Echo.

Thanks...So its literally a 5 minute job to replace. Awesome.

@DoItWithDave

6 жыл бұрын

Houston Trapper awesome! Thanks for watching!

This is exactly what I needed to replace the primer bulb. Great video. No fluff. Just info.

Been watching KZread video's s for year's, and yours is one of the best I've ever seen, congrats awesome job....thanks a bunch.

Very Helpful, thank you for not dragging it out. Good Job!

When you tighten up a chain snug it up then pick the tip of your bar up then tighten the chain more if not when you cut and push down on the bar your chain will be too loose

@DoItWithDave

4 жыл бұрын

Thanks for posting. I agree with you, definitely need the chain to be tightened properly. Thanks for watching!

Very helpful, thank you.

@DoItWithDave

5 жыл бұрын

Thanks for watching!

Excellent video!

Thank you exactly what I was looking for. Perfect video bro. Thumbs up. Good job

DAVE HAVE 3 ECHO TOP HANDLES THAT ALL NEED NEW BLUBS. THIS HELPED A BUNCH!!!! TECHNICALITY -- AS IT STATES ON THE SAW, IT IS REALLY A "PURGE BLUB" NOT A PRIMER BLUB----IF YOU LOOK ON THE BLUB, THE TUBING FROM THE CARB TO THE BLUB GOES TO THE "IN" CONNECTOR, AND THE OTHER TUBING GOES TO THE TANK, NOT VICE VERSA-----ASK ME HOW I KNOW LOL

@DoItWithDave

5 жыл бұрын

Thank you for watching and thank you for the information on the proper name. It really does help others when they are attempting to do these repairs. I may be naming something different than what it actually is and it could definitely get confusing.

Did it with easy. Thanks

Tq sir..very helpful vid..

Very helpful

Great video ! Saved me probably $30-50. I'll buy you a beer if your ever in Lawton, OK

@DoItWithDave

6 жыл бұрын

Kelly Ginter well thank very much.

Good video thanks!

Great explanation, good vid, thanks, accept $1million in gratitude (wish I could give you the real $, you deserve it for this selfless service. Keep helping your fellow Man!).

@DoItWithDave

6 жыл бұрын

Thank you so much. 1 million in any form is wonderful to receive and I'll take it! I'm glad you found this video helpful. Thank you for watching!

my primer bulb stays deflated or depressed my saw will crank and start up but only run a few seconds. Do you think the bulb is bad?

@DoItWithDave

6 жыл бұрын

Reaper kinda sounds like a fuel line is clogged based on the prime bulb staying deflated, like it will push fuel but not pull it in. Could investagate the lines also check the spark plug is not cracked.

@stewartbruce2409

5 жыл бұрын

Dear Reaper, I had the exact same problem with my echo cs 3000. On the fuel pump side of the carb the tiny mesh screen was totally blocked with debris. It works great now after cleaning the screen. Good luck!!

where can i get this exact primer bulb?

@DoItWithDave

7 жыл бұрын

cslix I wrote down the model number then typed it in with the words "prime bulb" on Ebay. It came right up. Under $10.00. I hope this helps.