Sand them smooth and run it… they probably look bad but I bet with a little sanding they won’t affect anything.
@BillsGarageWorksАй бұрын
I don’t have a 90 degree yet either. I have found success using the ball style double cuts along with diamond ball bits. I put the cylinder in a vice so I can use two hands to control the dremel. It takes forever but it’s what I have. Sucks about the cylinder I’ve def done that, but we learning!
@tatepazaski5488
Ай бұрын
I might try that diamond ball. I talked to Dubbs and he's got a good 90 degree dremel but you would have to bounce a $250 check to get that one.
@HouseworksawsАй бұрын
Lol 😆 I shoulda probably waited til the end to say anything. I didn’t see the last part 🤣
@tatepazaski5488
Ай бұрын
They were pretty deep Big House. The plating isn't that good on those cylinders? And some of those dings were beyond the plating. I just looked online for a new cylinder and I can't find one anywhere. Trying to figure out if there's a cylinder piston combo from a different saw I can use. You know I probably shouldn't have checked that to the driveway just in case I can't find another one. Let me straighten out fins for days if I can't find another.
@Houseworksaws
Ай бұрын
@@tatepazaski5488 fins aren’t all that important anyways. I’ve used many cyls off saws that were crushed by the skidder or trucks and it bust lots of fins off. Also holes through plating is the same principle as grinding fingers in. As long as you can get them smooth you’re likely fine. Not giving you any BS or anything just saying in case it’s a last option type thing it’ll at least getcha running lol 😆..will it be pretty? No prob not but it may getcha running and that’s all that matters. Anyways best of luck man 💪👍🌲🇺🇸🌲
Пікірлер: 7
Sand them smooth and run it… they probably look bad but I bet with a little sanding they won’t affect anything.
I don’t have a 90 degree yet either. I have found success using the ball style double cuts along with diamond ball bits. I put the cylinder in a vice so I can use two hands to control the dremel. It takes forever but it’s what I have. Sucks about the cylinder I’ve def done that, but we learning!
@tatepazaski5488
Ай бұрын
I might try that diamond ball. I talked to Dubbs and he's got a good 90 degree dremel but you would have to bounce a $250 check to get that one.
Lol 😆 I shoulda probably waited til the end to say anything. I didn’t see the last part 🤣
@tatepazaski5488
Ай бұрын
They were pretty deep Big House. The plating isn't that good on those cylinders? And some of those dings were beyond the plating. I just looked online for a new cylinder and I can't find one anywhere. Trying to figure out if there's a cylinder piston combo from a different saw I can use. You know I probably shouldn't have checked that to the driveway just in case I can't find another one. Let me straighten out fins for days if I can't find another.
@Houseworksaws
Ай бұрын
@@tatepazaski5488 fins aren’t all that important anyways. I’ve used many cyls off saws that were crushed by the skidder or trucks and it bust lots of fins off. Also holes through plating is the same principle as grinding fingers in. As long as you can get them smooth you’re likely fine. Not giving you any BS or anything just saying in case it’s a last option type thing it’ll at least getcha running lol 😆..will it be pretty? No prob not but it may getcha running and that’s all that matters. Anyways best of luck man 💪👍🌲🇺🇸🌲
@tatepazaski5488
Ай бұрын
@@Houseworksaws thanks for the advice Big House!!