Catalyst Not Ready For Emissions Test? GET Catalyst Monitor Ready For Smog p0430 p0420 FIXED
Tired catalytic converter? Smog Test Catalyst Monitor trick for older vehicles. This will help with those P420 + p430 codes
Tired old car with high miles and your catalyst (CAT) monitor is not ready (INC)? I'm going to show you a little trick.
Look HERE, Vehicle Specific Drive Cycles for your vehicle is below........................
▶️Complete Smog Playlist • Drive Cycle | Tips to ...
▶️ 12 Minute Actual Drive • Smog Drive Cycle COMPL...
▶️ Demo EMISSION INSPECTION MONITOR Readiness (I/M) • How to use OBD2 Reader...
▶️ Acura Drive Cycle • Acura Emissions Drive ...
▶️ • Audi Emissions Drive C... Audi Drive Cycle
▶️ BMW Drive Cycle • BMW Emissions Testing ...
▶️ Chrysler Smog Readiness check • Drive Cycle Monitors R...
▶️ Chrysler Smog procedure • Chrysler Emission Driv...
▶️ Ford Drive Cycle • Ford Emissions Drive C...
▶️ Gm Drive Cycle • Don't want to risk fai...
▶️ Honda Drive Cycle • Honda Drive Cycle For ...
▶️ Honda Smog Readiness • Honda Smog Secret▶️ Ch...
▶️ Hyundai Drive Cycle • Hyundai Emissions Driv...
▶️ Infiniti Drive Cycle • Infiniti Emissions Dri...
▶️ Isuzu Drive Cycle • Isuzu Emissions Drive ...
▶️ Jaguar Drive Cycle • Jaguar Emissions Drive...
▶️ Kia Drive Cycle • Kia Emissions Drive Cy...
▶️ Land Rover Drive Cycle • Land Rover Emissions D...
▶️ Mercedes Benz Drive Cycle • Mercedes Emissions Dri...
▶️ Mini Cooper Drive Cycle • Mini Emissions Drive C...
▶️ Mitsubishi Drive Cycle • Mitsubishi Emissions D...
▶️ Nissan Drive Cycle • Nissan Smog Drive Cycl...
▶️ Porsche Drive Cycle • Porsche Emissions Driv...
▶️ Subaru Drive Cycle • Subaru Emissions Drive...
▶️Volkswagen Drive Cycle • VW Emissions Drive Cyc...
▶️ Volvo Drive Cycle • Volvo Emissions Drive ...
▶️ Catalyst monitor not ready? • Improve Your Catalyst ...
▶️ Catalyst Monitor Cheat • Amazing Trick to Get C...
▶️ Catalyst not ready? Watch this video • Cataclean Review▶️ Cat...
▶️ Evap monitor not ready? • Evap Monitor Not Ready...
▶️ EGR monitor not ready? • How to Get EGR Monitor...
▶️ Oxygen sensor not ready? • Essential tips to prep...
▶️ Oxygen sensor replacement • Oxygen Sensor Replacem...
▶️ Oxygen sensor heater element testing • How To Test Oxygen Sen...
▶️Link to Scanner in video amzn.to/2BZYqWo
▶️▶️▶️Video about recommend Full Color Scanner • Reset Check Engine Lig...
▶️Link to this full-color scanner amzn.to/2z0YTcF
▶️Lucas Fuel Treatment amzn.to/38p7Ps6
▶️Car Memory / Data Saver amzn.to/3mCTpKd
▶️Link to Scanner in video amzn.to/2BZYqWo
▶️▶️▶️Video about recommend Full Color Scanner • Reset Check Engine Lig...
▶️Link to this full-color scanner amzn.to/2z0YTcF
▶️▶️**If the video was helpful, remember to give it a Like and consider subscribing. New videos every Thursday**◀️◀️
Thanks for your support. God Bless
▶️www.spreadshir...
▶️Support RandonFix visit www.Patreon.com/RandomFix
▶️Support RandomFix via Paypal visit www.PayPal.me/RandomFix
▶️Facebook https: FB.me/RandomFix
▶️www.RandomFIXWorld.com
▶️ My computer for editing/uploading: amzn.to/2CLEx5w
▶️ Video editing software: amzn.to/2z1NvJY
▶️ Thumbnail software: amzn.to/2Bkjw5V
Disclaimer:
Due to factors beyond the control of RandomFix, RandomFix assumes no liability. Affiliate Partner: I'm may receive a fee from some of my affiliate partners for my first-hand recommendations.
Cat Monitor goes from “Inc” to “OK”
Why Your Car Is Still Not Ready For Inspection
Tricks to Use to Pass an Emissions Test Every time - How to Pass an Emissions Test
WHAT SMOG TECHS WONT TELL YOU AFTER YOU FAIL THE SMOG TEST FOR (INCOMPLETION OF OBDII SELF TEST)
Catalyst Not Ready For Emission Test? Cat Monitor “Inc” ? GET Catalyst Monitor Ready -EASY p0420 catalyst system efficiency below threshold p0430 automotive getting your car to pass emissions testing catalytic converter bureau of automotive repair car tipx astral auto repairs rosedale tech pittsburgh dtc scotty kilmer fixd app lexus
Пікірлер: 1 000
I did this on my 2004 Toyota Highlander and it worked like a charm. Catalyst Monitor kept being not ready for almost 2 weeks. Drove all the way from LA to San Diego and back, still failed. Did 6 drive cycles of going at 55MPH on the freeway for 10 minutes, still failed. Did this trick literally one time and it passed in the first attempt. Thanks!!
@RANDOMFIX
Жыл бұрын
Glad to help, thank you for the great feedback. I can only imagine how much you spent on fuel on the highlander from la to sd and back.
@cristianrosado3972
Жыл бұрын
What exact trick?
@RANDOMFIX
Жыл бұрын
I showed in the video ( this is good for older vehicles before 2008 and have a complete playlist for incomplete catalyst monitors kzread.info/head/PLDEbtVOPRC-h1BAzaWQ-6NSnmG0gwvgwP
@lenin1881
10 ай бұрын
@@RANDOMFIXMy 2010 Honda CRV car, of all its monitors, only 1 says incomplete, that is, not READY. ALL THE OTHERS ARE COMPLETE. READY. THE INCOMPLETE ONE IS 0S2. IT ALSO DOES NOT PRESENT A CODE AVAILABLE ONLY ON 02S NOT READY I CAN PASS IMPECTION LIKE THIS WITH ONLY 1 MONITORS NOT READY THANK YOU in New jersey
@fastfords9072
10 ай бұрын
I tried it on my 03 grand marquis doesn't work
Man 1600 miles and tried every drive cycle out there. Randomly saw your video and tried in in front of the good will while my wife was shopping and it cleared!!! Thanks for this video!
@RANDOMFIX
Жыл бұрын
Glad to help and 1600 miles a long time and lots of fuel. Thank you for the feedback
Magic trick!! Thank you so much!! I was desperate to make CAT ready for my 2001 camry to pass smog check, as I have spent many hours of on highway driving and put more than 500 miles without luck. This trick fixes the issue in just 10 minutes!! One note is that the 3000 rpm needs to be kept running for 4 mins to make my CAT ready. The BEST advice on the internet. Thank you so much again!!!
@RANDOMFIX
Жыл бұрын
Glad it helped! Yes the older your catalyst becomes the more time you may need to add to help it get ready.
It worked! Three mechanics gave me the wrong advice. So... I watched this video, bought a $22 code reader, and then drove to a bank parking lot. I put the car in neutral and revved the engine to 3000-RPM and held it there for 3 minutes exactly. I shut the car off and did the odb2 scan again. Catalyst = READY! Went back to the smog center and passed! (2008 Mercedes E350 with 110k miles) -- THANK YOU~
@RANDOMFIX
3 жыл бұрын
Sean, thanks buddy for the confirmation. Congratulations on getting your Benz e350 catalyst ready.
@periii86
Жыл бұрын
Thanks for sharing your story. Having a similar problem with my VW and will try it soon
BEST INSTRUCTION EVER, IT MEETS THE DATA NEEDED TO TRIGGER SYSTEMS TO COMPLETE MONITORS REQUIREMENTS. DID SMOG SINCE 1977/78. THANK YOU
@RANDOMFIX
2 жыл бұрын
Sam, thanks buddy for the great feedback!!! That is a long career in smog, congrats to you.
Thank you. Thank you. Thank you. After replacing knock sensors I drove 2000 4runner 1000+ miles, every weekend for 3 months getting up at 4am to drive so as to not attract attention with expired tag going slow on freeway following Toyotas drive cycle pattern. Got all, but catalyst monitor, then the 3 minute at 3K RPM finally did the trick. Thanks for taking the time to post this vid.
@RANDOMFIX
5 жыл бұрын
Thank you for th great feedback and it is much appreciated that you took the time to let me know. _Randomfix
Thank you so much. After I drove 400 miles and wasted a full tank of gas without any results, I did exactly what your video said and it worked Just fine on my 01 camry thank you again.
@RANDOMFIX
4 жыл бұрын
Melvin, thanks for the great feedback. _Randomfix
@Lex161Lexi
2 жыл бұрын
oo hope is works on my 99 camry
@RANDOMFIX
2 жыл бұрын
Good luck and let me know what happens.
Nah this is legit the best video on KZread😂😂😂 actually worked and I drove 300 miles prior to this video , 100 miles per hour nearly. Once I woke up and saw this video I immediately went to go try it, comments are not lying, well me at least. Went to go for emissions in Atlanta and it worked real fast
@chiefchimi
3 ай бұрын
Camry 2001
@RANDOMFIX
3 ай бұрын
@chirfchimi thank you so much for the great feedback about the smog video. I am glad it was helpful and I enjoy sharing the little things I have learned from doing the hundreds of time at car dealership! Much appreciated
It worked for my 2004 Toyota Highlander I/M readiness monitors were all checked off but catalytic still incomplete. After a Drive cycle was 150 miles in 2 days it seemed hopeless. So I started the engine to let it warm to normal temperature then reved it to 3000rpms for three mins. Let off the accelerator and scanned it again while idling. Cat monitor was READY Thanks for the video bro, it was really helpful 👍👍
@judahlion2067
2 жыл бұрын
Im that
@judahlion2067
2 жыл бұрын
Try that
@RANDOMFIX
Жыл бұрын
I appreciate your constructive comments, thank you for the feedback!
This information was absolute GOLD for me!! I was finally able to get my 1997 Saturn SC2's catalyst ready in literally 3 minutes. In my case, I drove the car at 3,000 RPM in 4th gear (it's stick shift) on the freeway. I then checked the car with my scanner via the OBD2 and it was ready. Further, it passed smog in California!!
@RANDOMFIX
2 жыл бұрын
David, thank you so much for the great feedback about it working on your 1997 Saturn SC2 ( cool car, best gm 4 cylinder in my opinion) Much appreciated
You seriously saved my life! I had to get an extension, drove over 300 miles and was failing multiple times. Did this once and it worked. I could cry. Sending you a little something on paypal as a thank you🙏
@RANDOMFIX
3 ай бұрын
Hi Laura, Thank you so much for the great feedback and for your special present you sent. I really appreciate you and you taking the time to post your experience.
Wow! I can’t believe this worked for me. I have a Toyota Camry 2001 and done the drive cycles but still fails on the scanner. Gave it one last try this morning on a cold start, kept the car in parked, stepped on the gas and held it steady at 3000 rpm for a little over 3min. Rescanned the car and the cat and evap drive cycles were cleared. Thank youuuuuuuuu! Very helpful vid. You saved me from thinking of replacing the catylitic converter.
@RANDOMFIX
2 жыл бұрын
Glad to help and congrats on getting that 2001 Toyota Camry ready to pass. Thank you for the feedback
Bro I was having so much trouble with my catalyst monitor and I saw this video today and an instant fix. Thank you so much🙏🏼
@RANDOMFIX
3 жыл бұрын
Ari, thanks buddy for the great feedback. I'm glad I was able to help with your catalyst monitor. Much appreciated 🙏
Wow! You are a lifesaver, it was a horrible long road to even find a reasonable used car & then it didn’t pass emissions here in WI. I did exactly what you did, step by step & I passed, can’t thank you enough for posting this!
@RANDOMFIX
Жыл бұрын
Glad it helped!
@theprmstrful1
Жыл бұрын
I'm in Wisconsin too. Having the same issue with my car
@RANDOMFIX
Жыл бұрын
Have you tried what I share in the video?
@theprmstrful1
Жыл бұрын
@@RANDOMFIX yep. 07 Hyundai Azera if that helps. Same issue with cat and evap
@RANDOMFIX
Жыл бұрын
Here is the Hyundai drive cycle kzread.info/dash/bejne/h653lqiHhNS0lKw.html Keep me posted. What caused for your monitor data to get lost or deleted?
Thank you so much!!! This worked for my 2000 Lexus rx300 on the second try. It has 220,000 miles on it. I had done several drive cycles which did not set the catalyst. I thought I might have to sell the car but who would want it when it won't pass emissions. It also was not worth replacing the three catalytic converters. This post made 5 years ago with 279K views. You are great. I am a lifetime mechanic (77 years old) and never knew this procedure. Thanks again. Ernie
WORKED!! On my 2001 Camry with 189K. Tried all the drive cycles repeatedly, this is the only one that got the CAT ready. Surprised the heck out of me!
@RANDOMFIX
2 жыл бұрын
Brian, good to hear the video helped on that 2001 Camry. Thx for the feedback.
@briank7523
2 жыл бұрын
@@RANDOMFIX Thank you for making this available!
Randomfix today you just earned yourself a new subscriber. I own a 2001 Camry, changed a new catalytic converter and drove for 4,100 miles mostly on freeways and street. It was still not ready for smog test OBDII kept reading {Incomplete} Thank you so much because tomorrow I was planning to go back to the shop where they installed that catalytic to complain and get it changed/replaced. Thank you so much coz a total of 10 minutes only fixed my car and ready for smog test.
@RANDOMFIX
2 жыл бұрын
Hi Vital, thank you so much for the great feedback and congrats on getting your 2001 Toyota Camry ready to pass!!
Thank you soooo much! This trick saved me from stressing out. It helped my 2000 Camry's catalyst to be ready for smog, while doing a few driving cycles could not get it ready. ❤❤❤
@RANDOMFIX
Жыл бұрын
Glad to help and congrats on getting your 2000 Camry ready for smog.
I had a number of issues this year to get my 2001 Camry smogged. After some repairs to old hosts, cleaning EGR valve, etc, everything checked out except the catalytic drive cycle. Went back to the smog shop numerous times after 300-500 miles and kept being told "you need to drive it some more". Finally, the smog technician told me to look up Toyota's drive cycle to see what I may be missing. Ran that twice late in the evening hoping not to tick off any freeway drivers wondering why I was only doing 55mph and trying to maintain 35-45 on the trip back on a smaller road for both cycles. NONE OF IT WORKED. Came home, started looking and saw this video and after letting the car sit overnight, starting her up and letting her warm up, 3 mins at 3k rpm and the monitor went from INC to OK. THANK YOU for this tidbit of into! Now to get the car smogged!
@RANDOMFIX
4 ай бұрын
I’m glad to help with your 2001 Camaro smog and thank your sharing your success. Just know that passing your Camaro in the future will get harder to set this cat monitor as it ages. Make sure you have a memory saver kzread.info/dash/bejne/iaqHq6OKY67Whdo.htmlsi=vaOrn21lHwKlZUn4 I have others say that they went 3k for 4 minutes when the weather was colder or very high mileage. Have a great Sunday
@bedrock8
4 ай бұрын
@@RANDOMFIX LOL, I wish I had a Camaro! Unfortunately, it's just another pedestrian Toyota Camry sedan I bought from new and racked up 286k miles on it!
@RANDOMFIX
4 ай бұрын
@bedrock8 no shame in a Camry. Sorry my auto correct got Camaro by accident. The Camry is solid especially the 2007 to 2011 4 cylinder models. I think these were are the best sedans ever built. I sold my 2019 and regret it now. The new Camrys are not as wide even though they appear to because the lower base but the top toes in.
This worked the first time after trying the 200 miles and driving at 50-55 multiple times! Let's go!! You the man!!
@RANDOMFIX
28 күн бұрын
I glad to hear that worked for you the first time!!! Just of out curiosity what was the year and make of the vehicle?
My guy!!! Really was dreading doing the drive cycle for my 2002 Toyota Tundra v8 lmt. !! Plus where I live it’s always busy on the highway! So 1008 miles later , I found your video! TY! 3 mins at 3k rpm worked like a charm. Plugged in my OBD and BAM, CAT ready baby!
@RANDOMFIX
3 жыл бұрын
Kymberly, thank you so much for your great and sharing your success on your 2002 Toyota tundra. Much appreciated ☺️
@jessica18730
Жыл бұрын
i am driving closed to500 miles tundra 2000 v8 i going to try this tomorrow !!
@kymberlyherrera7814
Жыл бұрын
@@jessica18730 do it! Hope it work for you as it did for me
Thank you soooooo much, I was going crazy over the fact I had a bad cat, once I tried this, it worked! Mechanics nor the smog check guy knew this, thanks man!
@RANDOMFIX
3 жыл бұрын
Glad it helped!
This worked on my 2014 Nissan Versa!!!! I did so many drive cycles and nothing was working at first. This worked on the first try. Thank you so much for this video!
@RANDOMFIX
4 ай бұрын
Hi Sam, Glad to help, thank you for sharing your success on getting your 2014 Versa catalyst monitor ready. Please sub, like and if possible support the channel if the content helped you save time and money. As a smaller KZread Creator, my channel runs on the generosity of viewers like you. ☕️ ☕️☕️Buy Me A Coffee! bit.ly/Cofy4RF
I tried a few times like the video, with car parking 3.000 rpm for 3 minutes, but didn’t worked! So read a few comments and I tried like they said! First I drove the car around the parking lot for 4 minutes at 3.000 rpm and my oxygen sensor turn OK on scanner, but the catalyst still INC and a tried again and nothing happened. So I drove in a high way for 7 minutes 55 mph and 3.000 rpm, when I stoped the car catalyst was ready!! This work on my Mini Cooper convertible 2008!! Thank you so much for help us!
@RANDOMFIX
Жыл бұрын
Glad to help with your mini cooper, thank you for the great feedback!
I drove my car days for the catalyst monitor to be ready but had no luck. Yesterday, I followed the instructions in this video for my 2005 VW Beetle (127K miles) and the incomplete code on OBD scan tool was moved to OK. Thank you RandomFix!
@RANDOMFIX
Жыл бұрын
Glad to help with your Vw beetle. Thank you for the feedback and taking to time to post your success.
Thanks for the video, here's my story. I have a 1999 Mazda B2500, and had gotten my renewal notice 2 months prior. Hadn't gotten it smogged yet, and early on the morning of the 5th of July it was stolen off the street in front of my house. Didn't think I'd see it again, but it was recovered almost a month later. They broke the clockspring when they busted the ignition, so I had to order and wait for the new one. I had to disconnect the negative cable to do the installation, there by making the drive cycles necessary. They had stolen my plates as well, and didn't want to be driving 300 miles in SoCal freeways without plates. Less than 2 weeks left to get renewal done. I took it on a local 2 lane road for about 10 miles. That left only the evap and cat to finish. I tried the method in this video but cat still didn't finish, so I took it out on the same local road and drove it in 4th gear (it's a manual) at around 50 mph keeping an engine RPM of 3500. The cat cleared in about four minutes. Just passed smog this morning.
@RANDOMFIX
4 жыл бұрын
Tim, glad to hear you passed and you got truck back. Thank you for sharing.
I have been trying to get this monitor cleared for 3 weeks now. I have tried everything, all tips and tricks. Your method worked. 3 minutes of your method cleared the catalytic monitor. 98 Expedition 4x4, 5.4l v8.
@RANDOMFIX
6 ай бұрын
I appreciate your feedback Sorry for the late reply
Thank you soooo much... just fixed my problem. I'm worried about my catalyst thinking if I'm going to replace it coz I drove 200 miles and it's not yet ready, but thankfully it's solved my problem. Once again thank you so much..
@RANDOMFIX
2 жыл бұрын
Anytime.
Thanks for the tip ! Doing this got my EGR ready, but the CAT stayed not-ready. I decided to go on the freeway and drove for about 3 minutes in 3rd gear with the RPM constantly at the 3000. My speed was on the average 62 mph doing this. This got the CAT in ready status !!! Did this to my son’s 2008 Mazda 3 which had the battery disconnected for weeks. So for those of you folks this tip did not work, try this variation. Again, THANK YOU.
@RANDOMFIX
3 жыл бұрын
Arsenic, thank you so much for sharing your tips and I'm glad your found the video to be help. Much appreciated 🙏
@DucatiPaso750
2 жыл бұрын
I'm going to try the same. Get on the freeway, but it in 3rd, hit 3000 RPM and switch on the cruise control. Hopefully it will work.
@RANDOMFIX
2 жыл бұрын
David, let me know how it goes. Thanks
@josevilla7257
10 ай бұрын
Work 07 vw thx
Thanks so much! I had to do it twice. But the second 3 minutes at 3000 rpms did the trick on the CAT monitor and I went and passed. Try it a couple of times! This was on a 2001 Toyota Camry. Thanks RANDOMFIX!
@RANDOMFIX
2 жыл бұрын
Tim, thanks buddy for the great feedback and for taking the time to post this.
@riasinger1724
2 жыл бұрын
Same results same car! So happy 🙌🏽
@RANDOMFIX
2 жыл бұрын
Glad to help
Just did this with my 2005 Nissan Altima, after it not being ready for the longest and overdue at that THIS WAS A GOD SEND THANK YOU!
@RANDOMFIX
Жыл бұрын
Glad to help with your 2005 Altima. Thank you for great feedback
I can not thank you enough for this tip. After paying for a new catalytic - wouldn't register in the car - drove 400 miles 2 tanks of gas, still one last warning wouldnt clear. Tried this thi am, yes with a cold start, and drove it straight to smog, boom, it passed. Ty ty ty, i was about to drive the dam car into a wall and call it a day😂
@RANDOMFIX
4 жыл бұрын
Rachel, that's awesome nes, Glad to help.
@ciscokaliking8469
3 жыл бұрын
It’s gonna happen once or twice more in our lifetime. God willing more. So don’t forget. Dear comment readers. Hint hint.
@xxxjayxxx11
3 жыл бұрын
Same here. Thank you so much bro Keep this type of videos rolling....
Thank you so much . It worked perfectly on my 2000 Camry . Appreciate it a lot . You are genius 👈 Update : Smog test passed in next 15 min :) Thank you again . You have made my day .
@RANDOMFIX
2 жыл бұрын
Glad it helped
Thank you very much. It worked for my 2001 Toyota Camry. I had to run the engine twice in order to trigger the catalytic mon from INC to OK.
@RANDOMFIX
3 жыл бұрын
Thank you so much for the positive feedback and for sharing your success on your 2001 Toyota Camry catalyst monitor setting.
🎉🎉🎉 I have just spent a half a tank of gas in two days driving around with nothing working and I finally stumbled upon this video and even though I felt skeptical I tried it anyways. Sure enough I came back to the smog center and it fucking worked!! thank you so much for posting this video anyone who’s read this comment it absolutely works!!
@RANDOMFIX
Жыл бұрын
Glad to help and thank you for sharing your success. Ouch 1/2 tank of gas wasted.
This is nuts! I first thought of this as an old wives tale. My cheap harbor freight monitor proved that it worked. Thank you for posting!
@RANDOMFIX
4 жыл бұрын
My pleasure. _Randomfix
Thank you SOO SOOOOO MUCH!! this worked on the second try for my 01 Toyota Camry!! 😩🙌🏽 I’m so happy this shit has been causing me so much stress! I took a 100 mile trip and it didn’t do anything, yet this 6 min fix worked like a charm. Much appreciation to you 👍🏽
@RANDOMFIX
2 жыл бұрын
Ria, thank you so much for the great feedback and confirmation. Much appreciated
You're a damn genius. This 100% worked for my 2005 Scion TC. Thank you!
@RANDOMFIX
3 жыл бұрын
Thank you so much for the great feedback. I've been called many things but genius I really like. Lol, seriously I'm glad the video helpful and it helped avoid driving around town for no reason that to set a smog monitor. Have a great day.
I can confirm this work with 2007 Nissam Altima. Here's what I did. Went to an empty parking lot . Turn on the Car, set it on park let the car warm up til the needle thing reaches in the middle between hot and cold. I turn everything on AC on full blast for 10 minutes. After ten minutes, I rev the car to 3000 rpm for about 3 minutes mine took only 2 minutes, you will know if you completed drive cycle if your car stutter. I did this twice to make sure that it was working. My Oxygen Sensor Monitor went from INC to Ready.
@RANDOMFIX
2 жыл бұрын
Hi Eddie, thank you so much for the confirmation on the a 2097 Altima package
Randomfix your awesome I have a 2015 Honda crv , sensor one was replaced , it failed inspection because it was not ready, I tried all to make it ready nothing worked, ONLY YOUR INSTRUCTIONS WORKED TO MAKE IT READY. Thank you so much
@RANDOMFIX
10 ай бұрын
Glad to help with your Crv smog Thank you for posting your experience and success
Just tried this for my 2005 suk forenz that wouldn't pass smog. It passed after doing this. Thank you!!! :)
@RANDOMFIX
3 жыл бұрын
Thank you so much for the feedback
Thank you very much, my car just passed the inspection...more power to you and your family...
@RANDOMFIX
2 жыл бұрын
Tom thank you for your great feedback and for taking the time to post this great feedback. Much appreciated.
RANDOMFIX, Thank you so much for this amazing video? This really worked on my 2003 Toyota 4runner. I was failing the Catalyst Mon, the mechanic kept insisting the catalyst had to be replaced. You have saved me head aches and lots of money....
@RANDOMFIX
Жыл бұрын
Glad to help and congrats on saving that $$$ on the 4Runner Thanks for the great feedback
Thanks sir I just got my 2004 toy rav4 cat code clear using your method 😂👍👍👍👍
Notes: 1. Make sure to do this in a well ventilated area, definitely not in an enclosed garage. 2. Start vehicle from cold and let idle for 7 mins (keep an eye on the temperature). 3. Press foot pedal until 3,000 rpm and let idle for 3 mins. Update one year later: I couldn’t clear the catalyst after trying everything and wasting so much gas. I just gave up and after 6 months of driving occasionally (wfh), I got it checked again and the cat was cleared. I had felt it wasn’t gonna happen so maybe try that if you are stuck. I paid the renewal fee but was driving around with an expired sticker luckily nothing happened to me 😂
@drk_8984
2 жыл бұрын
Weird thing is for me it’s off and on it’ll go from ok to inc idk what to do
@jt.633
2 жыл бұрын
@@drk_8984 I’ve seen other people say when they see that it is OK they drive straight to smog check without ever shutting off the car.
@drk_8984
2 жыл бұрын
@@jt.633 That’s smart I’m going to have to do that thanks
@AlexOsbaldo
Жыл бұрын
@@drk_8984 you have a problem with your stay alive memory
@samuelriebel5535
Жыл бұрын
After the catalyst fault clears, can you turn off the engine or do you need to keep it running all the way through the smog test?
Thank you so, so much! I've been struggling with getting the CAT monitor ready. I've driven 524 miles, but it still would not complete. After following your instructions, it became ready, but this was after a second attempt. I was planning on driving several more hundred miles before seeing your video. It was so pleasing and rewarding to see that the CATALYST monitor turn from red to green on the scanner, just having it idle at 3000 rpm's for 3 minutes, after the engine warmed up, without driving an inch!!! By the way, the car is a 2000 Lexus ES300, with over 198,000 miles. Again, thank you so much for the video. God bless.
@RANDOMFIX
2 жыл бұрын
That Lexus es300 is one of the hardest vehicle to get the catalyst ready on. Thank you for your support and feedback.
@rkgsd
2 жыл бұрын
@@RANDOMFIX Lots of old Toyotas with the same engine.
@HyttmanTjsmma
2 жыл бұрын
Did this on 2000 ukon it did nothing
@masonfalcon6933
2 жыл бұрын
@@RANDOMFIX sure is. I have an 02 lexus es300 and I'm having that problem for the evap and catalyst. I'm going to try your method
Dude you did it for me! My 2012 Fit failed smog for exactly this reason. I did the who drive cycle deal and nothing. Then I did yours and it worked. Many thanks for posting this video. Bill in Los Angeles
@RANDOMFIX
2 ай бұрын
William, Glad to help you and I know getting the monitor ready for smog can be a real pain especially in Los Angeles and with heavy traffic. Thanks for the great feedback
@oseanillu2057
24 күн бұрын
Hey I also have a fit that’s failing emissions because of this reason, but for some reason my Honda fit automatically drops RPM’s after holding the throttle longer than 2 minutes when I’m in park. Did you experience the same thing?
WORKED!!!!! Finally passed inspection in close to 2 years!!!!! Thank you!!!🙏🏼
@RANDOMFIX
4 ай бұрын
I’m glad to hear that. Wow 2 years is along time. What make model of vehicle is it and what was the issue?
@Frankenstein6.2
4 ай бұрын
2001 Tacoma PreRunner 2.7 2WD. P0420 code was on, cleaned cats and replaced both O2 sensors, cleared the codes and drove around before inspection. Catalyst Monitor kept coming back not ready after HUNDREDS of miles of driving around and doing the stupid "driving cycles" on youtube. Couldn't pass the state inspection until I found your video!@@RANDOMFIX
Thank you bro you're a lifesaver, tried this on my 2000 toyota camry one day before my tags were due and it worked, had to do it twice for it to work but it sure beats driving around trying to get it to clear, thanks again just subscribed
@RANDOMFIX
2 жыл бұрын
Jay, thanks buddy for the confirmation. Much appreciated
@HardcoreUly
2 жыл бұрын
When you say you did it twice did you let the car cool down overnight before the 2nd attempt? Or did u simply let the vehicle idle for a minute after the 1st attempt before repeating the 3min part where u rev it at 3000 rpm?
@chuey799
2 жыл бұрын
@@HardcoreUly after the 1st attempt i just turned the car off completely for a couple of seconds and then did the process again and after the 2nd attempt i turned the car off again and then checked it with the obd2 scanner and it was cleared
@marcosman3393
6 ай бұрын
How you test twice do have to wait till next day mine won't clear need help
00 Odyssey with 266k. Ran the same test holding at 3k rpm in park for 4 minutes. Readiness did not pass! Then got on the freeway and held it steady at 55mph for 3 minutes (no AC, no cruise control) and passed immediately. Just a heads up for Honda owners.
@RANDOMFIX
3 жыл бұрын
Just made a video for honda owners, thanks for the as well. kzread.info/dash/bejne/oY55rtiTZMfHnqQ.html
Just wanted to say thanks. Although these exact steps didn’t work for me on a 2003 Toyota Camry, but I knew where you were going with this. On the Toyota Camry, there is a button on the transmission stalk to turn on/off the “Over-Drive” system. Once I turn that OFF and drove it on the freeway, the Catalytic Monitor went to Ready. Basically, I needed to get to a higher RPM (above 3k) on the freeway for an extended period of time and that monitor will clear. When the over-drive is ON, it would always hover around 2k, this doesn’t make the catalytic converter hot enough and so the computer will never say it is ready. So if you have a vehicle with this type of over-drive transmission, turn it off and go for a freeway drive and in 10 minutes of freeway driving it will clear. I guess if I had to do it again I could have done this same procedure longer and it might work, so instead of 3 minute just let it rev up to 3k RPM for longer.
@RANDOMFIX
22 күн бұрын
You hit the nail on the head. You have to get catalytic converters hot and when you turned off the overdrive you made the engine work harder and it produced more heat. I didn’t recommend turning off the overdrive as 3k rpm on certain vehicles like Chevrolets, bigger v6 and v8 motors will be destroyed as those motors lose oil pressure. Thank you again for sharing.
New cat installed 06 solstice. This didn’t do it for the catalyst monitor, so I decided to drive at lower gear at around 40 mph and RPM’s at 3000 or a little higher for about 10 miles. Tested and all ready to go. Thanks
@RANDOMFIX
2 жыл бұрын
Thank you sharing your story on your Pontiac Solstice
Thanks ! I been trying for weeks to fix the issue with my cat not being ready and this did it ! Thank you Thank you !
@RANDOMFIX
5 жыл бұрын
Jose thank you for taking the time to post this great feedback and I really appreciate it. I wish you all the best. _Randomfix
I have a 2000 Yukon. This worked for me. What I did, was drive the truck in 2nd gear (number 2 on the dash) at 45 mph. This gear and speed was perfect for achieving a consistent 3000 rpm. I have a Bluetooth ODBII connected to my phone, so I literally watched the Catalyst Monitor go into 'ready' state as I was driving. It was around 10 mins of in town driving, which I had several stops in between. The reason why I drove until of doing it in my driveway is because my exhaust is fairly loud and I didn't want to disturb my neighbors. I just made a trip to get lunch a productive one, and it worked!
@RANDOMFIX
Жыл бұрын
Thank you so much for the great feedback and congrats on setting the Cat monitor on your 2000 Yukon! is the catalyst original?
@bigthreewheeler
Жыл бұрын
@@RANDOMFIX you're very welcome and thank you for your information! Yes, I have the original cats on my Yukon.
@zerocal76
Жыл бұрын
Hi bigthreewheeler. Could you please tell me what BT OBDII app you used? I haven't been able to find one that monitors the stuff needed for smog checks. Thanks in advance friend!
Seeing as I'm currently not allowed to drive my car due to failing a test that includes an emissions test, I'm very thankful you posted this.
@RANDOMFIX
9 ай бұрын
I’m glad to help and please let me know if you have any questions. I will be happy to point you in the right direction
@LindaCharles-ll6lm
3 ай бұрын
Did this work for you ?
This video is a time/money saver ! It worked on my 2003 Toyota Highlander V6 with over 331k miles after multiple tries. Thank you !
@RANDOMFIX
Жыл бұрын
Glad to help get that Highlander ready for smog. 331k miles, you gotta love toyota. Are the cats original?
@trickdaddy7148
Жыл бұрын
@@RANDOMFIX yup
@paulmcfarlin5646
Жыл бұрын
It worked for my 05 cadi sts but the 02 sensors will not get ready after 5 drive cycles and 400 miles.
Thank you... you saved me a ton of money, i appreciate you taking time and help us out, i just passed my smog inspection after months of frustrations.
@RANDOMFIX
4 жыл бұрын
Shawn, thanks buddy for the great feedback. Randomfix
I tried your technique and I had no change to the code clearing. The next day I checked and it was cleared. Thank You!
@RANDOMFIX
Жыл бұрын
Glad to help and thank you for taking the time to post your experience of setting your catalyst monitor
I have 2000 Sienna with 150k miles I jumped my battery 2 weeks ago so didn't pass the the smog due to No Data. So I did drive cycle for 150 miles and got everything ready except for catalyst monitor So here is what I did : Cold start overnight Idle for 15 minutes Revved 3,000 rpm for 3 minutes (It would jump after 2 minutes but kept going) Drove about 2 miles (to Advanced auto parts to pick up the DTC (OBD2) scanner without turning off the engine) Connected scanner and drove to freeway At speed of 50 mph for 3~5 minutes then drove 45 mph for 2 minutes then the CATALYST monitor changed to Ready status. So I took it to smog station and passed in couple days after.
@RANDOMFIX
Жыл бұрын
That’s awesome, thanks for sharing your success on getting your 2000 sienna catalyst monitor ready.
Man!!! I was skeptical. I kept trying to smog my 2002 toyota 4 runner. It didn't pass . They said wasn't ready. I came across this video and this shit really worked for me. Got a smog pass right after following the video. Thank you!!!!!
@RANDOMFIX
Жыл бұрын
Glad to help with your 2002 4Runner. Thank you for the feedback
I tried this way today. Working Perfectly! Thanks you so much.
Thank you so much!! I had all my I/M ready but i was having problems with the catalyst, i did this while my car was already hot and it worked perfectly.
@RANDOMFIX
2 жыл бұрын
Glad to hear that video helped get your catalyst ready. Thank you so much for taking the time to post this confirmation.
My catalys monitor would not come up and say okay after having work done on my truck because they disconnected the battery. I had been driving my truck with a bad misfire for several months because I couldn’t afford the replacement of the intake manifold. After finally getting it replaced I drove the truck for over a week and no luck with the catalys monitor. Then tonight I used a product called Cataclean. I Followed the directions and low and behold the cat monitor says ok! Omg I’m so relieved. I did try revving the engine to 3000 rpm three days ago after initially watching this video but it didn’t work for me. Anyway.. I just wanted to mention using the Cataclean in case anyone needs another method to try. Thank you for sharing your vid I’m sure you’ve helped many people.
@RANDOMFIX
3 жыл бұрын
Awesome thanks for sharing, I have 2 videos about cataclean. In the future as your catalyst ages even more, cataclean will even become useless for you so when that happens check out my video on how to buy direct connect catalysts for about the price of 5 bottles of cataclean. Thanks for sharing.
@wyattsdad8561
3 жыл бұрын
@@RANDOMFIX okay I definitely will. Any chance you could post that link on here for me? You’re probably right, I’m sure my cats will need to be replaced at some point. I never got a code for them, just a slow monitor. But I drove for several months with a bad misfire and sometimes two cylinders were missing due to water getting in the plug wells. I’d remove the coils and clean them out from time to time but my check engine light would flash sometimes. So they’re probably not in great shape. Again thank you for making the vid and sharing.
@RANDOMFIX
3 жыл бұрын
Here is the link kzread.info/dash/bejne/iaZl2Kiqc9HWdMY.html and all smog related videos are in the Smogs tips playlist.
THANK YOU SIR!!! YOUR TECHNIQUE WORKED FOR MY TRUCK. I WAS ABIT SKEPTICAL AT 1ST, BUT WITH SOME PATIENTS IT WORKED!!
@RANDOMFIX
3 ай бұрын
Glad to hear what sort of pickup did you have and how many miles?
@omarparish6748
3 ай бұрын
It's a 2007 i290 isuzu pickup with over 300k miles. I did the sea foam solution for catalytic converter where the 02 sensor is placed and it help alot..Thank you again..sir!
I can I leave the OBD scanner connected while doing this procedure or do I need to disconnect it. Edit: I left the OBD Scanner connected while driving and it worked. Also what finally got me to pass the "Catalyst Not Ready" was to do the driving where you go about 65-70 mph then let the car slow down on it's own without touching the pedal.
@RANDOMFIX
Жыл бұрын
I appreciate your constructive comments, thank you for the feedback!
I was in the business for 20 years, but I've never heard of this trick. I can tell you how it probably works. At the air filter, your vehicle is sucking in 78% Nitrogen, 21% Oxygen, and about 1% "other" like Carbon Dioxide, (Al Gore's favorite gas,) Helium etc. The ideal exhaust ends up as 78% Nitrogen, 16% Carbon Dioxide, 5% Water Vapor, 1% "other," and NO pollutants - HC, CO or NOX. One common misconception is the idea that if your exhaust has low pollutants, then everything is fine. The CAT monitor is not based on pollutants coming out the pipe, it's based on how well the CAT stores, and uses Oxygen, in the catalyzation process. This process is cyclic in nature, similar to the way an Oxygen sensor sends high / low signals to the ECM. First the CAT stores Oxygen, then releases it as needed, then stores and releases again. So the ECM monitor is looking for NO Oxygen at the rear, after the CAT, Oxygen sensor. This lack of Oxygen tells the ECM that the CAT is storing and using the Oxygen properly, and the monitor is completed. With this in mind, what probably happens when you raise the engine to a stationary high RPM, versus driving on the road, is you are putting your GOOD RUNNING engine in a state with a minimum of unused Oxygen in the exhaust. Any exhaust pipe leaks, before, but especially after the CAT, and before the rear Oxygen sensor, will doom the CAT monitor. An exhaust leak after the rear Oxygen sensor, will not affect this CAT monitor. Raising the RPM increases the exhaust pressure, which makes it more difficult for ambient Oxygen to leak into the exhaust pipe. So this added pressure, which masks the problem of exhaust pipe leaks, is a major key in this trick, in my opinion. This no load, high RPM condition, probably creates the lowest exhaust Oxygen possible, at the rear Oxygen sensor.
@angelgirowall8673
2 жыл бұрын
Thank you so much for this great explanation.
@NuclearBalls1
2 жыл бұрын
@@angelgirowall8673 My pleasure!
@ryno2062
2 жыл бұрын
Most understandable and clear explanation of the CAT I've ever read. Thanks for that. And I'm sure anyone that stumbles on to your post will appreciate your explanation as well.
@RANDOMFIX
Жыл бұрын
Sorry for the late reply! did you find a solution?
Idk if this did the trick but I own a 2002 Toyota 4Runner. I drove for 45 miles nothing. Pulled into a parking lot didn’t do it for 3 minutes did it for 2…. Drive down the street to my house 3-4 minutes CAT was ready 👀🔥👍🏿. So thanks!
@RANDOMFIX
Жыл бұрын
Glad to help and yes for older toyotas this is the trick!!!
Yo, came back to this video to say you’re a life saver, I was able to get all my monitors to read besides catalyst, even drove the vehicle for 3 minutes around town keeping rpm’s at 3k and it didn’t work, I figured I’d just pull over and try what you said cuz why not what do I have to lose? And guess what? It worked 😂 on my 17 370z
@RANDOMFIX
5 ай бұрын
Thank you for the great feedback and your success with your 2017 370z. It worked on the side of road because your vehicles catalyst was warm already. I appreciate you posting this your experience.
This worked for my ‘01 Tacoma. Thank you!
@RANDOMFIX
4 жыл бұрын
Great to hear! and I appreciate the feedback.
Worked for me after replaced cat drove more than a month wouldn't clear, today drove in a lower gear held rpms at appox 3000 for 3 or 4 min finally cleared. Thanks
@RANDOMFIX
4 жыл бұрын
My pleasure and I'm glad to help.
Random fix you have earned my subscription I will be subscribing tonight my catalyst was not setting or not ready I tried the driving technique that you had mentioned that didn't set it last one was trying the bottle of the catalyst cleaner or whatever that is the bottle you recommended best $27.99 I've spent saves me $300 plus bill of having to buy a new cat I appreciate it very much like I said I'll be subscribing tonight thank you!!!!!
@RANDOMFIX
2 жыл бұрын
Hi Steve, thank you so much for the great feedback and I'm had you are doing the channel here. Much appreciated. Congrats on getting your catalyst monitor ready.
Worked like a charm....2001 Camry 4cyl with 232,000 miles.....runs like new
@RANDOMFIX
2 жыл бұрын
Johnny, thank buddy for the confirmation and congrats on getting that 2001 Camry ready to pass.
Bro. You didn't think to show us the CAT ready on the scanner afterward?
@solidpnoy
4 жыл бұрын
Royce Johnson because it obviously did not work! Waste of time!
@Joelo7734
3 жыл бұрын
It worked for me
@RANDOMFIX
3 жыл бұрын
Thank you for the confirmation 👍 🙏
@luckyvids
2 ай бұрын
@@solidpnoy Why did you said that,@solidpnoy? Did you try it?
@RANDOMFIX
2 ай бұрын
@luckyvids read the comments it works great for older vehicles especially Toyota vehicles. Don’t believe the brave boys behind their keyboard. It cost nothing and is to try for yourself
EXACTLY What I need for old camry
@johncandy7237
3 жыл бұрын
Did it work?? I have a 2001 Camry and the catalytic still shows incomplete 🤦🏽♂️
@RANDOMFIX
3 жыл бұрын
Yes, this is for older cars such as your 2001 Camry.
@user-is5to3jq3j
3 жыл бұрын
Thanks im doing this now
@RANDOMFIX
3 жыл бұрын
Glad to help and I'm here if you need anything else.
@hectorcoronel619
3 жыл бұрын
Nope, didn't work. Driven over 1,000 miles on 97 accord 4cly ,every monitor is good except catalytic monitor.
It worked after driving around for so long and no results tried this and it worked! On a 08 Civic Si
@RANDOMFIX
3 жыл бұрын
Great, thank you for the feedback.
@musicmansdream
3 жыл бұрын
2004 expedition no go...
My 2000 camry wouldn't complete the cat test, no precheck engine codes, Drove over 300 miles tried 2 different drive cycles i saw online and nothing. Scanned before I tried this method to make sure it was still inc And it was and this method actually worked. I don't think this method works every time but It sure worked this time. Thanks mane
@RANDOMFIX
3 жыл бұрын
Ronin, thank you for the feedback and congratulations on setting the inspection monitors for your 2000 Toyota Camry. This drive cycle does not work for some vehicle so I made a vehicle specific video for each make. 2 months of work my hope is that every can benefit from those videos. They can be found on the smog tips playlist.
Thank you. I drove 150 miles yesterday and nothing. I tried this today and passed real quick. It worked on a 05 nissan Sentra.
@RANDOMFIX
4 жыл бұрын
Moe, my pleasure. _Randomfix
Does not work for 2002 Sienna. Warmed up on a cold start let it idle for 12 minutes. Let it sit at 3k rpms for 3 mins. Nothing
@RANDOMFIX
Жыл бұрын
I appreciate your constructive comments, thank you for the feedback!
BROO YOU SAVED MY LIFE! I TRIED THIS AND IT TURNED ON MY CAT MONITOR. PLS PLS PLS GUYS DO YOUR DRIVE CYCLES!!! I did mines for the first time after driving 500+ miles and nothing seemed to work until I did that drive cycle. Only took about 8min.
@RANDOMFIX
4 ай бұрын
I’m glad to help, anytime! Thank you so much for gracious feedback and for making evening!!!
Thanks for good advice , got a 2007 Nissan xterra done 211,000 miles on the clock my car runs good and due for a inspection .
@RANDOMFIX
3 жыл бұрын
Edward, thank you for the great feedback 😀
UPDATE !!!!!!!! THANK'S TO ONE OF THE COMMENT BELOW MY CAR PASS CATALITIC READY BUT I RUN THE CAR AT 3000 RPM FOR 4 MINUTES AND BOOM READY !!!!!!!!!!!!!!!!!!!!!
@RANDOMFIX
10 ай бұрын
CONGRATS AND THANKS FOR SHARING YOUR SUCCESS. What are your driving and how many miles?
@davidl4315
2 ай бұрын
@@RANDOMFIX Camry 2001
AWESOME THANKS FOR THE TIP . IT WORKED JUST LIKE YOU SAID ‼️ ONE HAPPY CAMPER OVER HERE. YOUR THE MAN👨🔧🧰
@RANDOMFIX
3 жыл бұрын
Anthony, I'm glad the video was helpful.
Thank you so much for the info..did this to my 2001 thundra after a week of driving and not able to clear the cat test.. 3 min did the job thnks again
@RANDOMFIX
3 ай бұрын
Glad it helped with your 2001 tundra and thank you for taking the time to post your experience
@LindaCharles-ll6lm
3 ай бұрын
Did u only have to do it once ?
@manuelgutierrez3855
3 ай бұрын
@@LindaCharles-ll6lm I did it twice first try didn't work second did
I just passed emissions. Did this more than 6 times. It didn't work. After trying this, what I did was drive on the highway at a constant speed at 55MPH for 7 minutes. Don't use the brakes. Let the car coast to a stop on its own. My catalyst monitor started working. Went right to the inspection place and passed. Wish I saw this sooner since I got 2 tickets since my inspection expired 4 days ago. Oh well. I can sleep better now 😁
@RANDOMFIX
2 жыл бұрын
Good to hear and thank you for the update.
@klutch...
2 жыл бұрын
@@RANDOMFIX Keep up the good work. Thanks again👍
@RANDOMFIX
2 жыл бұрын
Thank you ❤️
I did 2 tries for my 04 Sienna - didn't work, thanks for your video.
@l31007
4 жыл бұрын
Thank you for sharing your experience with us. It's good to know.
@RANDOMFIX
3 жыл бұрын
Hi, Peter, every car is different and these 2004 sienna and 4runners are a pain in butt. Try it for yourself and I'm here to help.
@RANDOMFIX
3 жыл бұрын
Good to hear the news and thank you for sharing.
What's an "older vehicle"
@RANDOMFIX
5 жыл бұрын
Hi Adrian, Great question. 1975 to 1995 will be emission probe test. as where 1996 to 1999 will b emission probe test and obd2 readiness tested. Vehicles 2000 and newer will only be obd2 readiness test.
Did it today for my 2000 Nissan frontier all monitors passed/ok except for catalytic converter said “Inc” (incomplete) held throttle at 3000 rpm for 3 minutes and 30 seconds gave it a quick rev and then turned off truck for 10 seconds turned it back on held rpm at 3,000 rpm for another 3 minutes and 30 seconds, gave it another quick rev checked monitors and they were complete thank you so much saved me lots of gas money and allowed me to keep my favorite truck with the 3 minute 3,000 rpm trick never in a million years did I think this was a fix / procedure for setting catalyst monitor I drove 500 miles attempting to set catalyst and ended up setting them in my driveway (-:
@RANDOMFIX
3 жыл бұрын
Thank you so much for sharing your success on your truck. I appreciate your feedback and for letting me know.
thank you, it worked. you have saved me a lot of headache, money and time.
@RANDOMFIX
8 ай бұрын
My pleasure to help, thank you for sharing your results
Should you keep your scanner attached so you can keep an eye on it in case it works before 3 minutes? So that maybe you don't have to run it the whole 3 minutes?
@RANDOMFIX
Жыл бұрын
Sorry for the late reply! did you find a solution?
@l31007
Жыл бұрын
@@RANDOMFIX I ran the car twice for 3 minutes each time. It didn't work. What I found out that for many cars, the computer is looking for what's called a Drive Cycle. Each car has a different routine its looking for, like drive at 30MPH for 30 min, do certain full stop exercises, idle for 5 min. Each car has different drive cycles. The computer is basically seeing that you are driving your car regularly. My mechanic told me to drive my car on the freeway for 100 miles. That didn't work and was a waste of gas and time.
@RANDOMFIX
Жыл бұрын
So how did you pass? What are you driving? What are you driving?
I’ve did it twice and nothing 😔
@RANDOMFIX
4 жыл бұрын
Did you try a 3rd time?
Worked for my 2004 Celica GT thank you!
@RANDOMFIX
8 ай бұрын
Glad to help, yeah this works great for pre 2008 Toyota really well.
Took a few tries but it finally worked. The trick was making sure all the accessories are turned off, AC, defroster, radio, etc.
@RANDOMFIX
3 жыл бұрын
Ramond, Thank you for sharing your results about getting your Catalyst ready. I know the a/c+defroster can make a difference, but you also mentioned the radio. Please share with me your experience and what's the make model and year of your vehicle? Many thanks _Randomfix
Hell yeah. I’ll try this today after work!
@RANDOMFIX
3 жыл бұрын
Let me know what happens and if you need anything please let know what you are driving and any specifics about the vehicle that you feel are important. Thanks and good luck.
Right on this video helped me out boss.didn’t even had to run excessive miles to be ready to pass smog
@RANDOMFIX
Жыл бұрын
Jose, thanks buddy for the great feedback about the smog video. What are you driving?
@josebedolla3742
Жыл бұрын
@@RANDOMFIX I currently have a 2000 Toyota Camry se 4cly.
@RANDOMFIX
Жыл бұрын
Awesome cars and simple to work on. Thanks for sharing buddy.
So do you do this then drive to DMV I HAVE 2001 Ford ranger owned for 4 months runs great no issues no check engine lights they DMV scan it says emissions not ready
How does the ECU know that the CAT is in the ready state? is the ECU interpreting the downstream O2 sensor reponse?
@RANDOMFIX
24 күн бұрын
Yes, in a sense. Catalytic converter are triggered and so once the right the right conditions ( parameters )are met the ecu will show it’s ready.
Thank you! I tried your advise and it worked. Thank you!
@RANDOMFIX
2 жыл бұрын
Glad to help, thank you for the feedback
I tried this and it did t work. Drove cycles on my truck and CAT still Inc. took it to the mechanic, everything is fine. I/M ready is checked green but Cat Inc and won’t pass smog in California. Are there any other options I can try like changing the battery? @randomfix
@RANDOMFIX
Жыл бұрын
Here the playlist just for incomplete catalyst monitors kzread.info/head/PLDEbtVOPRC-h1BAzaWQ-6NSnmG0gwvgwP What are you driving? Please provide additional information like the miles and reason for smog data being deleted.
I have a 1999 ford crown Victoria p71 the problem with it is I have two incomplete monitor evap and catalyst I have drove the car more then 150 miles and the monitors won’t set what would I do?
@RANDOMFIX
Жыл бұрын
You need handle the p0071 and Here are some possible causes Failed or faulty ambient air temperature sensor A short in wires or broken wires An open or shorted ambient air temperature harness Corroded electrical circuitry and/or connectors Sensor covered by foreign objects Once you fix the issue then complete a drive cycle.
Thanks Random fix. Just what I needed. I’ll try and do that today and I’ll get back with you. Thanks 🤙
@RANDOMFIX
3 жыл бұрын
Sure, Benny if you still need help just let me know what's the make of your 1996+ vehicle so I can send the exact directions for your vehicle or check the smog tips playlist and find your make. Good luck.