title says it all. if you would like to support my channel use one of the links below paypal.me/pools/c/8rf8aLKqVS you can email me at koba49@yahoo.com
Жүктеу.....
Пікірлер: 19
@RME19113 жыл бұрын
I’ve been enjoying this cast bullet series and nomenclature. Thank you
@levinlevinallday3 жыл бұрын
I love the lee sizer dies. I've resized many .357 bullets for 9mm when I run low.
@richardperry41156 ай бұрын
Very helpful video. Cheers.
@robgraff3 жыл бұрын
Thanks for the video. I never knew about the NOE sizing die, looks like a good set up.
@yukon45453 жыл бұрын
I have the RCBS and an old Herters lubra-sizers. I have the RCBS mounted on the heater. Tip: propane torch to warm up the sizer. NOT Hot! It helps to have the lubra-sizer warmed up when switching dies or adding lube, etc
@nonamelyman35493 жыл бұрын
Ok.... that does it, i'm ready for adoption.. i just want 10 % of your knowledge. That would make me happy. Have a great day sir.
@yukon45453 жыл бұрын
You can run the Alox lubed bullets through the Lee while still wet. Size, put back in the bucket, shake it again, dump on wax paper to dry. TaDa! If the bullets are softer, pistol bullets for example, they'll size without lube, no problem.
@paulbarela6548 Жыл бұрын
Excellent video. Do you know if there is a tool specifically made to size and clean lead cast bullet heal and base. I use lee sizing dies will be willing to use any. I need to true the base because when it comes out of the mold it has a crease in it and uneven on the bottom.
@CincyPlasmaTech3 жыл бұрын
From the casting mold to the sizer, what is the change in dimension of the bullet?
@joemorganeatmyshortschannel3 жыл бұрын
very good info koba had a question and may be a stupid question but you would know the answer 223 remington in short supply but 222 remington everywhere here are they close enough for a reloader to make work in a 223 chambered gun?
@TheKoba49
3 жыл бұрын
NO THEY ARE TWO DIFFERENT CARTRIDGES
@joemorganeatmyshortschannel
3 жыл бұрын
@@TheKoba49 thats exactly what i thought and that is probably left alone on the shelf i figured if they could have been used for that they would be gone hope that surgery goes well for you and have good one.
@cory87913 жыл бұрын
Unfortunately lee is discontinued the push through that can be used in any press to there brechlock systems only so if you are in the market for one then you better jump on it!!
@robgraff
3 жыл бұрын
@cory8791 Where did you hear this?
@cory8791
3 жыл бұрын
@@robgraff I was told by lee customer service that they are going to Phase out the old style for the one that fits there new app press that only excepts the breech lock system bushings if you look they are already selling them now so it won’t be long the the old style will be gone!!
Пікірлер: 19
I’ve been enjoying this cast bullet series and nomenclature. Thank you
I love the lee sizer dies. I've resized many .357 bullets for 9mm when I run low.
Very helpful video. Cheers.
Thanks for the video. I never knew about the NOE sizing die, looks like a good set up.
I have the RCBS and an old Herters lubra-sizers. I have the RCBS mounted on the heater. Tip: propane torch to warm up the sizer. NOT Hot! It helps to have the lubra-sizer warmed up when switching dies or adding lube, etc
Ok.... that does it, i'm ready for adoption.. i just want 10 % of your knowledge. That would make me happy. Have a great day sir.
You can run the Alox lubed bullets through the Lee while still wet. Size, put back in the bucket, shake it again, dump on wax paper to dry. TaDa! If the bullets are softer, pistol bullets for example, they'll size without lube, no problem.
Excellent video. Do you know if there is a tool specifically made to size and clean lead cast bullet heal and base. I use lee sizing dies will be willing to use any. I need to true the base because when it comes out of the mold it has a crease in it and uneven on the bottom.
From the casting mold to the sizer, what is the change in dimension of the bullet?
very good info koba had a question and may be a stupid question but you would know the answer 223 remington in short supply but 222 remington everywhere here are they close enough for a reloader to make work in a 223 chambered gun?
@TheKoba49
3 жыл бұрын
NO THEY ARE TWO DIFFERENT CARTRIDGES
@joemorganeatmyshortschannel
3 жыл бұрын
@@TheKoba49 thats exactly what i thought and that is probably left alone on the shelf i figured if they could have been used for that they would be gone hope that surgery goes well for you and have good one.
Unfortunately lee is discontinued the push through that can be used in any press to there brechlock systems only so if you are in the market for one then you better jump on it!!
@robgraff
3 жыл бұрын
@cory8791 Where did you hear this?
@cory8791
3 жыл бұрын
@@robgraff I was told by lee customer service that they are going to Phase out the old style for the one that fits there new app press that only excepts the breech lock system bushings if you look they are already selling them now so it won’t be long the the old style will be gone!!
@jefferyboring4410
2 ай бұрын
3 yrs later their available
Great video thanks!
Saw some carcano on midway