Can it be repaired Astra H Z16XEP twinport manifold Part 2
Today we continue with the repair on the Astra Z16XEP lower inlet manifold
MUSIC CREDITS
Intro/Outro Track
Syn Cole - Feel Good [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Syn Cole - Feel Good |...
Free Download / ncs.io/feelgood
Background Track
Tobu - Sound of Goodbye [NCS Release]
• Video
Free Download / Stream: ncs.io/sog
Unfortunately the eBay Seller the I bought the miniature bearings from is no longer registered, the bearing type I used were MR148, 8mm x 14mm x 4mm search for these on eBay but please check the size before ordering
Пікірлер: 23
Hey vauxrez, you have to take the valves out, there are plastic canisters on the end where the valves move in the aluminum, first check these before you put everything back together. With me they were already loose and 1 was even half worn away. you do not want these parts to end up in your cylinders.
just bought a spare manifold to repair the worn pivots that actuate the flaps ' managed to get some 10 by 5 by 4 bearings as well as star clips if i need to relocate flap spidles
Good info vids subbed 👍👍👍
Hi you can help me with the series of bearings you used at twinport. Thanks
I think the bearing size is MR85ZZ
pure genius - what was the case, was it p300 301 302 303 304 314? how the car acted after your fir Sir? i'm curious, since I am dealing with mentioned issue just for so long...I've replaced spark plugs ignition coil as wel..both twice and the car is getting ups&down on rpm metter till it heats up to 105 defrees which is the thermostat opening moment, afterwards it works just fine and rpms are still at it's level (roughly 780 + - 30 ),before i'm getting like 300-400rpms wben breaking or some plus mentioned p's above, i've noticed that unpluging egr valve makes the car 'stronger' like and it seems that problem is not that touching...i've hard my issue might be related toward inlet manifold, the car has 250 kkm , compression is just fine as i reach 180 on spedometer (same engine zafira b z16xep)
Hi, your videos are great. I had similar ticking in my zafira b 2005 1.6 petrol. I had loose baffle plates and swirl flaps. I resealed the baffle plates and done the bearing mod on the swirl flaps, car runs like new. I am now worried how hot the area of the bearings get and if it will melt the glue? Any ideas. Many thanks again for your informal videos 👌👌👌
Hey a have a question, what was the symptoms of these bearing worn out? I have a Astra h 1.8 xer and on take off or under load it struggles for second or two , consumption goes sky high , no eml present whatsoever
@vauxrez8831
2 жыл бұрын
The only real problem I had was a lot of hesitation at all speeds, engine jumping/jerking but the main reason I did what I did was to try and cure the tapping/rattling noise which turned out to be a much bigger problem as explained in later videos
Va salut! Mie imi apare masina cu cheita in bord iar ca eroare pe tester p1113 tension elevada circuit electrovalva cum crede ti ca as putea rezolva problema?
Did your Bearing fix hold up or did they fall back out from vibration from the engine?
@vauxrez8831
3 жыл бұрын
Thanks for your comment That's a very good question I drove the car for about 1500 mile without issue before I swapped the engine I am planning in the near future to do a series of videos stripping the old engine so I will make a point of investigating the bearings
@SpyHeli
3 жыл бұрын
@@vauxrez8831 Hi, are they still holding up with your repair or did the bearings falls out now ?
Can you tell the dimensions of small bearings? Thanx for video.
@vauxrez8831
3 жыл бұрын
I think they were 5 mm X 10 mm X 4 mm MR105 but I can't be 100% sure as it was over 2 years ago now
Hello! What was the mileage on the engine at the time of disassembly?
@vauxrez8831
Жыл бұрын
Hi, it was quite high milage at 123000 miles
How big are these bearings? 8x14x4mm???
@vauxrez8831
Жыл бұрын
Hi thanks for your comment, yes that's correct, MR148, 8mm x 14mm x 4mm but please check before ordering
Cuantos km te paso?
@vauxrez8831
3 жыл бұрын
198000 km
@user-xl5dz6od9r
3 жыл бұрын
@@vauxrez8831Great video!! You improved the system ,, Was the bearing purchased custom? Thanks for answering, Mine is 103,000km I recently bought it and watching several videos, I was worried about the bugs you mention, 1, The intake with the plastic system, 2, the system in the injection that is involved I imagine I still have quite a few km left
terrible video.....camera is not even on what you're doing most of the time.