What are your thoughts on Cerakoting?

@majs1032

6 жыл бұрын

Its looking awesome m8

@cjcimperman4856

6 жыл бұрын

Looks great

@growbikebuild3032

6 жыл бұрын

Looking good

@aljazferk5726

6 жыл бұрын

*2 stroke for Life *

@truthberkley2610

6 жыл бұрын

Looks awesome but I like the coarseness of powder coating I would do that more

Im a certified Cerakote applicator and apply it professionally. Fantastic job for a home job. few things I would do differently is gas out before blasting, use a spray gun that can spray an oval instead of just a small circle, and use weight instead of volume when measuring paint. Also cerakote is applied much more evenly when ran through the proper filter before pouring into the gun, also the BIGGEST mistake people make is not letting the part level out for 15-20 minutes before throwing in the oven. Other than that this is a great job on this video.

@chadcoady9025

4 ай бұрын

Thanks for taking your time to share pro tips!

@walkerjohnson2325

3 ай бұрын

the procedures we have most all parts have to be phosphated before spray can be applied. I normally outgas after phosphating right before i mask and apply spray. Is the procedure of gassing parts out meant to be done before blast always?

@jaredbailey9096

3 ай бұрын

what good does gassing out do to a part that isnt down to bare metal? what is its been previously coated with like an oil based paint @@walkerjohnson2325

@dreknows

Ай бұрын

Bro is sandblasting necessary if I want to get into this. And what size nozzle is best I heard .8mm? Thx

@dreknows

Ай бұрын

If you live in Florida I'd love learn

I'm a Cerakote applicator and your video is great! One suggestion if you follow this guide would be not to use an airbrush. The nozzles are way to small for good flow. Your parts turned out great but it really should only take one wet coat. Due to your nozzle being to tiny achieving one wet coat was difficult without several passes or coats. Cerakote recommends a .8 nozzle which is perfect and can even achieve a almost glossy slickness. A .8 nozzle can be found on most hlvp touch-up guns which can be found very cheap. I believe you will get much better results this way and a more beautiful finish. Also gas out only takes 20 minutes if your oven is up to temp. Once again this is a great diy guide. Thumbs up! And subbed!

@CameronNiemela

6 жыл бұрын

Thanks Tim! I'll definitely try those out

@ErikisOfficial

8 ай бұрын

5 years late but passche airbrushes go up to 1.0 fluid nozzle. Especially the VL series. Excellent for cerakote.

Thanks for the helpful overview of the Cerakote process. Tip: Shelf-Life refers to how long the products can be preserved in storage before they start to degrade. Pot-Life refers to how long the reactive chemicals remain usable after being mixed.

Great video, tutelage, lessons, explanations, camera work, audio & NO lame loud music or condescending remarks. I appreciate & applaud you. You would make a phenomenal teacher / shop instructor. Look forward to more videos. Thank you. Oh yeah 2 stroke for moto X & 4 stroke for street

Love these videos! You all your videos made me to start getting into painting my bike! keep up the good work, and 4 Stroke all the way!

Man, I can hardly wait to get a real shop so I can start doing things like this on my projects. Simply awesome results! Thanks for bringing this to our attention. Keep up the great work, Cameron!

@junigonzalez3482

3 жыл бұрын

Hey man it's been aa year since this comment came I was wanting to see how's business going I would love to see the progress

Your channel is very inspiring..... I've never rode a dirt bike, but I just recently bought my 7 and 9 year old both some used crf50's, like I said used, so I've been all over youtube on restoring them and making them look half way decent for Christmas gifts. Now I'm getting all this crazy thoughts on stuff I can do to their bikes. Thank you for all the sharing that you do. You are awesome!!!!

2 stroke all the way! It's the rider that makes a 2 stroke "work" !!! Awesome job on the triple clamp, looks awesome. I've been wanting to do some powder coating at home but wasn't sure about the oven. Never thought about a regular stove. Not big enough to do rims but small parts would be perfect!!!! Thanks for these videos!!!

Hey Cameron. I recently stumbled on to your channel when looking for information on fcr carbs. I'm really impressed with both the quality of your videos and information. Just a few quick observations. As someone who paints and airbrushes, when you set your spraying pressure, set it with the trigger or button pressed, it will always drop a few psi, and manufacturers give you spraying pressures, not static. Also, when spraying paint start with the top surfaces. When you start with the sides, dry overspray winds up landing on the top and makes for a rougher surface when you get to painting the top, although from what I can see it doesn't look like it affects the cerakote process. I'm assuming it flows out like powder coat during the curing process. *I'm nit picking*, but some food for thought if you start painting parts. Again, excellent videos and your work is a source of inspiration for my machines. Having only ridden 4 stroke quads, its hard for me to decide. One thing is for sure, 2 strokes sound just plain cool. Keep up the great work man, and thanks. Pat.

I did an AR 15 upper/lower/forearm set as meticulously as you did but I blasted, decreased, acetone bath, heated, sprayed, baked. Came out looking great. As did yours.

@Silvermeow

3 жыл бұрын

I did it backwards like this once as well and it turned out fine, but its better to do it the other way

Thanks for the video. It was nice to see someone that is thorough with a well thought out process.

2 strokes!!! Love the how to vids. Would be awesome to see more.

2 stroke all the way.. I have a cr125 and that piece would look great for my build. Thanks man keep up the great work! Love the vids

Awesome presentation. Thank you. 2-stroke. I have 2 Yamaha RD400's. You would really enjoy an old 70's 2-stroke street bike. A restoration video of an old RD 400 would be great.

I'm watching this for probably the 30th time since the video first came out and I still get impressed at your attention to detail and results every single time. Hope everyone is staying safe in these strange times 👍🏻

Those clamp looks awsome !! 4 stroke.

Having had the joy of riding two stroke, I feel my references are now leaning toward four stroke. Great job coating those parts!

Thanks for the very good video. You answered many of my questions. Oh, and I have only had one trail, Honda SL175, 4 stroke back in 1971, had a back operation in 1972, no bikes since then. Loved that bike!

This is the weirdest gun customization video I've ever seen.

@InClaymont

3 жыл бұрын

Lmao! You clicked on the wrong video homeboy.

@TheAnytony

3 жыл бұрын

@@InClaymont *swooosh* :P

@dwightschrute3862

3 жыл бұрын

Anton H it’s woooosh, not Swoooosh

@aterack833

3 жыл бұрын

fakecubed this is like an Homage to the videos where they avoid calling guns guns, lmao

@JeremyBurnett

3 жыл бұрын

Yeah I was recommended this video after watching fire arm customization vids as well... Cool to see the process though. Places charge a small fortune to do this.

Excellent job. Just a couple of points to help you achieve more consistent results ( not better 'cos that already looks good). First, don’t forget to clean the tips of your pliers. If they aren’t degreased you could get contamination from them. Secondly, set your air pressure on falling pressure. If you haven’t used the reg recently on a standard reg you can get slip-stick friction on the regulator diaphragm which can cause a variation of up to 5psi actual pressure at the gun tip although the gauge is reading the same.

Looks great and great content as always and I’m a 2 stroker always thanks for the upload

AMAZING work!! Wow!!! Great step-by-step instructional too, so fun to watch.

Always loved 2 strokes! Loved to get a KX500 again.

Cameron, 2 years on, how did the Cerakote hold out? Maybe a good time for an evaluation on the Ceracote coatings and applications? Would really appreciate it as there is little or no experience with it. Good luck with your videos, they are great and inspiring! Frank

Great videos ! 4 Stroke. I've done a lot of painting and you look like you have it figured out. Keeping things clean is the secret. For a rack, just weld some steel angle into a 6' X 6' square, weld a 3' piece on each end to bolt 4 cheap casters to and you have a cheap, easy to store rack to hang thins on while painting and drying. Keep on making useful and interesting videos !!!

@CameronNiemela

6 жыл бұрын

Thanks John! I'll give that a shot.

Great instructional video. Thanks for the video. I love 4-strokes..

Straight up class act; excellent detailed video!

Oooooooh.... 2 stroke, the aroma of fuel/oil mix! Keep up the great work Cam!

Interesting process i.e. ceramic coating ; I will use this for coating a victorian wood Parlor stove: they do have a chrome coating I will try to get that. Thanks!

Awesome work, wouldn't mind to try this out myself on some car parts. I see this coating is quite popular on guns.

I have several Cerakoted firearms, it works great and I love it!

congratulations for your work, I would like to have half of your talent and that here in Brazil had these top paints

@dannymoneywell

3 жыл бұрын

Aqui, amigo: cerakotebrazil.com.br/ Tem sim.

Just subbed. Your videos are so in depth! I thought I was the only one that went this crazy with cleaning my bikes and such.. props!

@CameronNiemela

6 жыл бұрын

Welcome to the channel! Haha good to hear we're on the same page there

@MrBrutalMachine

6 жыл бұрын

+Cameron Niemela haha right on man!

Very nice!!! Thanks for sharing the process of cerakoting.

Muito bom seus vídeos! Seu trabalho é como a de um profissional relojoeiro! Nos mínimos detalhes! Um grande abraço parabéns! O tradutor ajuda muito!

2 stroke beacause they sound good and are easy to maintain and more

2-Stroke!! I have 3. Lol Well.. 4. Tuesday I drove 200 miles to buy one of two near mint machines.. 1. 2003 KX500 $3900 2. 2008 CRF450r Black edition $2800 Both were great looking clean bikes and had all the power. If I had the cash I would have had no problem buying both. The KX500 is in my garage. 😁 I'll definaty be doing Cerakote thanks to you. Love the videos. Thank you so much for the education you provide. John

@markknight6910

5 жыл бұрын

John Hobson Hope you keep the videos going ! Very clean, to the point, pro level work and documentation !! Can't honestly make a choice between 2 / 4 stroke. They each have their own nitch/purpose !!

@fidelcatsro6948

5 жыл бұрын

i own a 115cc yamaha from 1983 ~ 2 strokes rule!

@Dennis-pe6zx

5 жыл бұрын

@@markknight6910 Umm it was Cameron that did the video.

@raccoon344

5 жыл бұрын

John Hobson can I have it

@scott250r2

5 жыл бұрын

2 stroke power. All the way. I am a proud owner of an 87trx250r and its awesome.

This looked sick! I'm going to have to give this a try on my mountain bike's lowers and crowns.

Hola Cameron! Just a quick note to say that I have become a huge fan of yours! You are very talented! Your technique for teaching and capturing details and technique on video is outstanding! I also respect your mechanical talent and innovation. You definitely approach things the correct way! I have learned a lot from you... thank you! I am currently deployed (pilot) in El Salvador and I have been spending all my free time catching up on your excellent vids. I recently returned to bikes after a twenty year hiatus and am the proud owner of two Kawasakis (KLR and Concours 14). I am having a blast on both bikes and I am looking for a more trail capable machine that is more MX oriented. I just wanted to send you some giant KUDOS for a job well-done! BTW... your track riding isn't bad either! Oh yeah... FOUR STROKES all the way! BRAAAPP! I had been considering trying powder coating and now, it looks like Cerakoate will be an option as well. You got me excited to get back into my shop when I get home! Respect!!!

I have owned both 2 and 4 strokes but I have to say I prefer a 4 stroke because of the power it offers all the way through the RPMs. Nothing like the sound and smell of a 2 stroke, but if I had to ride one I would choose a 4 stroke.

@nzzs203

4 жыл бұрын

@@chasemud749 2000 rpm's isn't exactly screaming... And why does everyone think a "power band" is some kind of magical power a two stroke has? They have *power* *valves* that help deliver the power when needed. I figured anyone that "raced" in the 70's on a "motor cross bike" would have known that...

Amazing work,, 4 stroker for me

PS love the attention to detail in your videos, keep up the good work bro can’t wait to see the finished bike

Well done! Excellent detailed description. Thanks!

Just to let you know, you should spray using the half half method rather than randomly. Randomly spraying will give it a uneven coating thickness that could result in tolerance issue.

4 stroke less maintenance and all that torque but kind of depends on the situation out here we ride in hollows so lots of straight up and down hill climbing so the low end torque is your friend but in other situations 2 stroke is King just not here lol project looks great definitely going to be trying this technique out thanks for the video

@leightonandrade8755

5 жыл бұрын

2 strokes are less maintenance, you don’t have to adjust the valves every 20 hours and you don’t have to do oil changes

@groggygreg1063

5 жыл бұрын

i would say more maintenance on a 4 stroke too... on dirtbike/motards at least. i had a husky 570smr, rebuild was expensive. been looking for a road registered cr500 for 15 years, everytime one come up im broke : ( just throw in some piston rings every now and then and off you go. the 4 stroke for sure a smoother ride though.

I just used this on my two Sig suppressors for my .300 blk out sbr. Works great.

Looks awesome man! Thanks for the video!

Overall a very nice project. I've watched a lot of cerakote related videos, and most are a little scary. Just a few small suggestions. Mix everything at 12:1. At 18:1 and 24:1, the surface of the coating, once it's finished, will scuff. You won't have that problem at 12:1. Also, you want to make sure whatever spray gun (or airbrush) you are using has a metal cup. The catalyst will actually melt the plastic cup, and mix it in with your coating. You also want to keep in mind that pressure at the gauge can be significantly less than operating pressure. We set our pressure with the air bleeding off of the gun to get it right. Too low and you can end up with dry spray. It's probably not an issue with an airbrush, but just wanted to mention it for those using a HVLP. Again, this was a very nice project. Burnt Bronze is one of my favorite colors.

@CameronNiemela

6 жыл бұрын

Hey thanks for your feedback! You make some great points there, I'll work those into the next project. Great videos by the way.

@BransonCerakote

6 жыл бұрын

Thank you Cameron. If you have any questions, our contact info is on our website, bransoncerakote.com.

@charlesdriggers199

6 жыл бұрын

Man, you are spot on ,but you and I, who have a gun shop, know that it is not as easy as it looks. I cerakote and do hydrographics, and have seen these videos. To many people think it is a piece of cake and try the DYI thing only to bring it to me to do it right. I am not trying to start anything here, but know it is better to use someone who does it for a living and backs their work up with some kind of warrantee.

@BransonCerakote

6 жыл бұрын

For what he was coating, none of the little mistakes would really matter. I would recommend clear coating them. I have done my share of repair work, but I also can say I've picked up a ton of little tricks from the DIY'ers.

@ghostdoors67

Жыл бұрын

Hi man, how to remove cerakote?

Like both!!

Cerakote is good stuff. I'm a design engineer and we switched from anodizing aluminum to Cerakote. It passed all of the hardness/chip tests we did!

Great work Done n shown easily keep up man i too luv doin such work in my spare time

2 stroke, always, loved the video Cameron

Good stuff. You'll get better control of your color if you keep the brush moving parallel to the piece. Don't swing your wrist from side to side, and try not to back up over each stroke as that gives you an uneven layer of color. Try not to trigger the brush in the middle of the piece as the first bit of color will always be a little dry. Also, why would you want 2-strokes when you could have four....!?

@JustinSmith-nt9ss

Жыл бұрын

You😂😂

Love your paint videos dude. Excellent work !!!

I absolutely love the finished look. I have no need to do this but loved your video especially all your shop tools. How do you like your HF sandblasting cabinet?

2 strome all the way ..........yz 125......... and I don't know why but after I watch your vids I some how end up watching them 3 or 4 times Cuz no one else makes good build vids like u

I have a 4 stroke 2015 crf 250r currently using you linkage rebuild video to help work on it

@PremixandPedals

4 жыл бұрын

His videos are so awesome and informative...used them as a point of reference a few times!

Haha I was waiting for the plastic acetone container result!😂 nice work, looks great. I’ve been into cerakote for a while now. Mostly the high heat products for turbine housings and exhaust parts. Amazing product. We’ve lowered the under hood temps of our turbo sleds dramatically. Plus the housings don’t look like shit after a couple rides.

Dude just wanna say thanks for making sweet vids. Your hard work shows. 👍

i prefer two stroke because i like power band and they always put a smile on my face

@nzzs203

4 жыл бұрын

Power band isn't a thing! You haven't a clue...

@TroNPopz209

3 жыл бұрын

@@nzzs203 what? lmao

@CFHmetalorama

3 жыл бұрын

@@nzzs203 The RPM range where an engine makes peak torque doesn't exist?

@Mac_F87

3 жыл бұрын

@@nzzs203 yeah they do. I prefer the blue one, much better power delivery then than yellow one. I changed mine when I first got my new bike, never looked back...😂

2 STROKE!!!✌️

You do. Such a good job with basic tools love ur videos just subscribed I build a lot of bikes race when I can but they put food on my table for my baby’s love to bring old dead machines back to life I am definitely going to up my game with ur technique thanks for sharing and I love 2 strokes going to build me a hybrid z400 with kx250 motor for my self (tacete) build

2 stroke best iv got 2001 cr250r 🤙love your video's mate thanks

man your vids are getting so pro...and i am going to say two stroke..only cause i do pocket bike vids..thumbs up

@CameronNiemela

6 жыл бұрын

Thanks! I appreciate that

@mark675

3 жыл бұрын

Pocket bikes are wicked fun 😎😀

Great video man, very educative thank you!!!

nice work - looks gorgeous!

2 stroke baby and i have a 2007 cr125 project going right now so it would be sweet if i got it!!!!!!

Two stroke!!! Who doesn’t love a screaming engine? Awesome job on the finish I’d like to see a sway arm finished in Cerakote would look sweet.

@petermarano8968

6 жыл бұрын

PURROS Leukos op

@maksimgavrilov2036

5 жыл бұрын

I don't like a screaming bumblebee I would rather hear the mean deep and throaty sound of a four stroke.

Wow that cerakote looks great! 2 stroke for life.

2 stroke is my game. Well put together video.

Holy shit, I thought this was Devin for a second haha I've heard him talk about his brother but this is the first time I've seen the channel

@pinakibhome3075

3 жыл бұрын

u r stonned

3:45 his reflection looks like he want to throw some hands with him😂

@bird4dbk420

3 жыл бұрын

🤣🤣🤣

Beautiful Cameron! 👏🏼👏🏼🔥🔥

Hi @ CN, Appreciate your insightful uploads. Always a good watch. Regards M@ uk

Really nice results bro. Thanks for sharing. Does this work on engines? Four strokes are of course best for larger bikes. But who could argue that a Bultaco two stroke trials bike isn't a serious classic. I've got two Honda fours with gear driven cams - the obvious best choice, despite what Ducati tell us. And I've got two 1980 Bultaco twinshocks. I learned to ride on an ex Post Office BSA 125 Bantam. My first road bike was a C50, probably the best engine ever made - until the NC27 and the VFR. My standards for a great engine are (in order of importance) a combination of: great engineering design, reliability, longevity, appropriate innovation, power, power delivery, and sound. And whilst I can appreciate the 'potato potato' sound of a Harley - as a novel gimmick, they lack any innovation that belongs in this century, isn't agricultural on nature, and dedicated to vibrating the fevered egos of geriatrics with beards! They also lack power to weight credibility in both engine and whole bike. I'm almost a geriatric with a beard btw, and I'd rather have something I can throw around on the twisty back roads, than join a moody landbarge cruise.

@CameronNiemela

6 жыл бұрын

Hey thanks for watching! Yes, it does work on engine parts. I'll be doing some Cerakote on the engine covers.

2 strike for full size bike and four stroke for pit bikes

I love 2 stoke and 4 stroke. It really depends on the application that you are going to have it for, which may be better for you.

I know I missed the chance to win but I’ve been binge watching your videos and I feel the need to comment. I prefer 4 strokes because that’s what I grew up on and modern day 4 strokes are insane. That being said I love a 2 stroke as well as long as it’s a dirt bike it puts a smile on my face and a feeling of peace and freedom in my heart when I ride.

Time to look on Craigslist for a free oven! I need to do a few things for my 125 project. That being said 2 stroke all the way! Remember kids, valves are for toilets.

@matthewnicholson566

6 жыл бұрын

Kevin Personius lol

@codenamenel

6 жыл бұрын

Toilets have Power Valves ?

@airgliderz

3 жыл бұрын

... another kid wannabe biker on a 125 two stroke toy.

@KevinPersonius

3 жыл бұрын

alan connelly 👍 whatever you say lol

@airgliderz

3 жыл бұрын

@@KevinPersonius glad you agree👍👍👍

You don’t need to soak for 20 minutes. Spraying and wiping it off is all you need if it’s not really cruddy with paint. If you do need to soak, do it in an ultrasonic unit for a couple of minutes. Of course, blasting shoots microscopic particles into the surface, and they may not come off. Baking may outgas for cast metals, such as aluminum, cast iron or zinc, but not steel. It could also microscopically cause oxidation. I can see these problems using a microscope. So overcleaning isn’t always helpful.

@ErikisOfficial

5 жыл бұрын

What about using m.e.k.

@0for30

5 жыл бұрын

Ah typical internet. Super helpful/interesting/insightful comment, followed by a moron with nothing, followed by some dick head pontificating about how the previous moron is so mind numbingly dumb they dont even know how to ask a question properly. What about 'what about using m.e.k.'? Ya dumb fuck? Elaborate on what exactly you're asking jesus fucking christ.

@chriseller6402

5 жыл бұрын

that is a cast aluminum and its alot harder to find a 2 foot long ultrasonic washer then going to harbor freight and buying a 100$ blast cab. looks like it worked just fine but id like to know how it holds up in the longer run

@0for30

5 жыл бұрын

@@chriseller6402 ya but whut about using m.e.k. tho

@chriseller6402

5 жыл бұрын

@@0for30 Just as you stated above on elaborating, are we talking using it instead of acetone for a faster process or using it to skip certain things. Personally i think its a little overkill but thats me and you can get acetone much easier than MEK at least in my area.

Awesome Video. I Love Four Stroke Engines. Keep up the great work. Nick.

Great results! What do you use to clean the cerakote out of the mixing tube and spray gun tank?

nice work. 4 stroke is better because who doesn't like more strokes :-)

@hannes_mlbx9599

5 жыл бұрын

They have about the same strokes, just the one ignite twice as often as the other

@oliverdurgen5953

5 жыл бұрын

the stroke count is related to each combustion event, not revolutions per minute. 2 and 4. not the same. in fact one is exactly twice the amount of the other.

@oliverdurgen5953

5 жыл бұрын

unless you only need 2 to get the job done!

@PremixandPedals

4 жыл бұрын

Are we still talking about dirt bikes? LOL!

@Retro_Rich

4 жыл бұрын

Tough debate. It’s like what’s better? “in out, in out, splash” or “pump, pump, squirt”.

is the sandblasting part necessary for cerakote to stick or can I do without it ? Awesome videos Cam, stay healthy and keep em comin

@antonyhibberd8728

3 жыл бұрын

According to the website sanding won’t work do you have to sandblast it seems pretty meticulous and like all the steps that they show are necessary. Search the websites videos on Cerakote

That was a nice video, I have never heard of Cerakote before very interesting too.

This is very good and detailed video, thanks. Do you have something similar to this using duracoat?

Me before watching: "wow, finally someone done this at home and use garage tools " Me after watching: "dude, you are pro AF, forget about it, I'll just spray paint "

@codelicious6590

4 жыл бұрын

Me too.

@codelicious6590

4 жыл бұрын

Dupli-Color high temp paints (with ceramic supposedly) I have found, leave a very nice and durable finish. I have been using the hell out of the "cast coat iron" which is like a dark metallic-ish grey with just a hint of bronze tint I really like it.

@bumstudios8817

4 жыл бұрын

@@codelicious6590 i have also used high temp engine paint before that was super durable

@billyburton3252

2 жыл бұрын

No joke. This is a huge pain in the @ss.

Beautiful man absolutely beautiful ! , uh two stroke but besides the point you took your time got the correct information and did it beautifully thank you ! This is a process I may end up trying myself for knives.

Excellent job. I like your attention to detail.

i do love my 2 strokes but im goig to have to go with 4 stroke

You're missing a water separator and also you wanna strain the cerakote before pouring it into your gun

As soon as you said you were putting that acetone into that drywall mud tray, I knew it was going to melt it!! I have that exact tray.

thanks for your video, i'm gonna try the cerakote on my 97 honda cr500, and my two 85 atc 250r's, banshee, and my 1975 kawasaki h2 750 with 89 gsxr suspension monoshock. 2strokes and rotaries! thanks again, keep up the great work!

@CameronNiemela

6 жыл бұрын

Thanks for watching Gerardo!

"TWO STROKE!!".

Its been done at home by thousands for many years now. Guys have been Cerakoting their own firearms ever since the stuff came out.

@Ryanmonts

5 жыл бұрын

Nobody said it hasn't. He said it was his first time

That’s an awesome color, looks amazing

That is super sharp. I prefer 2 stroke over 4 stroke and i love the sound of a 2 stroke. Only drawback is the mixing of the fuel. Stay safe brother. Randy

2-stroke

You are wasting your time with that airbrush nonsense. You are maxing the capabilities of something designed to draw pencil lines, and it's not enough to keep a good wet edge. Instead get yourself a mini gravity feed sprayer, or jamb gun. They can be dialed down to a magic marker size swath, but you would hardly ever need it. A good spray pattern for these types of projects is a regular spray can stream.

@JB-kf3yb

5 жыл бұрын

ipissed doesn’t really look like his time was wasted to me. It worked, and paid off. Glad you provided other usable sprayers. Thank you.

@Sms8668

5 жыл бұрын

ipissed So basically your saying U don’t know how to use an Airbrush.

@markrogers7304

5 жыл бұрын

An airbrush depends on the size of the tips you use. I use an airbrush often on 1/8 scale car bodies.