I can't think of any reason I will need to calculate anything like this. I watched the video simply for the joy of learning. I understood it right up until 9:19 when it comes to calculating the length of B,E,H. Where do you get the "Offset" number? The term offset is used throughout the video, but i don't think it's defined. Also, right in the last few seconds you introduce the term "Advance" without defining it. It appears these videos are too supplement what you taught during an in- class lecture, so perhaps your target audience is already supposed to know those terms. I've been enjoying your series of videos. I landed here because I'm redoing plumbing that a "handyman" did during a bathroom remodel. There's a veritable plethora of code violations from horizontal hard 90° turns, Sani-Tees lying on their back, and S-traps under the sink and tub. Good times.
@ryanthefox4889 Жыл бұрын
Painful
@dominiquepierre9163 жыл бұрын
I read book I understood but your video i just got confused
@edwardlogan5428
3 жыл бұрын
Which book did you read and was it good?
@dominiquepierre916
3 жыл бұрын
@@edwardlogan5428 I apologize for my comment You are great teacher and please continue your videos . I love your videos . Just I need to improve my basic knowledge in math
@leonwoods40522 жыл бұрын
DUDE WHERE IS THE CALCULATIONS? DID YOU MAKE THIS VIDEO TO HEAR YOURSELF TALK?. WHAT KIND OF TEACHING IS THIS ?
@edwardlogan5428
2 жыл бұрын
Thank you for your comment. Sorry to hear you didn't find the video useful.
@dominiquepierre9163 жыл бұрын
First explain what is spread ,what is spread allowance ,where is k ;where is x; You just read ; This is not teaching ! To be honest I did not understand your video This is not teaching 😁
@edwardlogan5428
3 жыл бұрын
K is explained as the spread between between D & G (Centre to centre measurement) and X is the variable that comes from the table. Thank you for your comment.
@dominiquepierre916
3 жыл бұрын
I studied plumbing apprentice book I appologize for my comment. I got it .
Пікірлер: 12
Great video! Thanks for the information
I can't think of any reason I will need to calculate anything like this. I watched the video simply for the joy of learning. I understood it right up until 9:19 when it comes to calculating the length of B,E,H. Where do you get the "Offset" number? The term offset is used throughout the video, but i don't think it's defined. Also, right in the last few seconds you introduce the term "Advance" without defining it. It appears these videos are too supplement what you taught during an in- class lecture, so perhaps your target audience is already supposed to know those terms. I've been enjoying your series of videos. I landed here because I'm redoing plumbing that a "handyman" did during a bathroom remodel. There's a veritable plethora of code violations from horizontal hard 90° turns, Sani-Tees lying on their back, and S-traps under the sink and tub. Good times.
Painful
I read book I understood but your video i just got confused
@edwardlogan5428
3 жыл бұрын
Which book did you read and was it good?
@dominiquepierre916
3 жыл бұрын
@@edwardlogan5428 I apologize for my comment You are great teacher and please continue your videos . I love your videos . Just I need to improve my basic knowledge in math
DUDE WHERE IS THE CALCULATIONS? DID YOU MAKE THIS VIDEO TO HEAR YOURSELF TALK?. WHAT KIND OF TEACHING IS THIS ?
@edwardlogan5428
2 жыл бұрын
Thank you for your comment. Sorry to hear you didn't find the video useful.
First explain what is spread ,what is spread allowance ,where is k ;where is x; You just read ; This is not teaching ! To be honest I did not understand your video This is not teaching 😁
@edwardlogan5428
3 жыл бұрын
K is explained as the spread between between D & G (Centre to centre measurement) and X is the variable that comes from the table. Thank you for your comment.
@dominiquepierre916
3 жыл бұрын
I studied plumbing apprentice book I appologize for my comment. I got it .
👎👎👎 I boo your video sir