Thank you for the video I just finished changing mine out and biggest trouble was getting the spark plug wire off the spark plug took me 3 hours taking it easy. 2014 c350 sport

@vikingrobot4179

2 жыл бұрын

You Can use a special set of pliers that have a half moon shaped loop at each end of the tool at an angle. It loops around the spark plug boot and you squeeze/pull otherwise you’ll fight them.

Thanks for doing this! Only video I’ve seen of my engine same type. Very helpful.

@deviousJames29

3 жыл бұрын

Same problem

Make video on how to take everything off struggling with ecu bracket

Good video. Glad you didn't remove the plenum assembly (cover with the 'V6' logo at 0:47) like some videos show - if you do remove it you need to get new plenum seals (don't re-use the old ones!) and they are not cheap else they will leak air and the engine management light will come on after a week: I know that because that's what my Mercedes dealer did 😣

@larryreno8293

Ай бұрын

That’s not true. I’ve reused them many times without a problem. I suspect they were not in place properly when the upper intake was installed.

Camera provided a clear view of this engine, only missing the real -time removal of the wiring harness and all it's weird clips. What tools are best for that?

I just did it without removing the manifold and am glad I didn't go through the extra trouble. That rear plug didn't seem so hard to me. I'm sure watching this video saved me a little time though.

@slidin5672

Жыл бұрын

Do you gotta torque down the new spark plugs?

@moisesperez4659

Ай бұрын

Spark plugs are indexed and must be torqued.

How to free the wires for the computer from the bracket you removed? There is a “screw” on the bottom the zip tie that’s screwed onto the bracket.

Smart man!! Good shiiii!!!

Thanks for posting! I was just looking at mine and wondered how the computer came off. Looked to me like it just pulled off and you confirmed it!

They have a special tool for that airbox clip it makes life a lot easier

@brassmule

Күн бұрын

It looks like a big Clic-R clamp?

@thor294

Күн бұрын

@@brassmule something like that I forget the name

@brassmule

Күн бұрын

@@thor294 It's definitely a Clic-R, and you're right, the tool for those makes it very easy to unclipped and re-clip them. Just did this job on a c350 today and confirmed it.

Great video. I do agree rear plug on driver side is pain in the ass to remove. After struggling for an hour I was unable to remove it. So now I have 5 new and one old plug lol. Lets see if I get any misfires in future. Thanks for making this video. Appreciate it man!

Good video

@C435I

6 ай бұрын

Doing the coil pack n plugs on my c300 right now

Good video my guy thinking of doing it myself instead of taking it to a shop! My only concern is do you have to torque the new spark plugs to a certain lb?? And do you have to change the coil packs also or can you just do the spark plugs?

@UnicycleWheelie

Жыл бұрын

Depends on the miles, my car had 60k, 23 Nm/17 ft.-lbs. on the plugs. 9 Nm for the coil pack bolts....NGK recommends a torque range of 18 ft-lbs to 21.6 ft-lbs for their plugs.

@slidin5672

Жыл бұрын

Okay thanks for the response and the lbs to use! I think ima go with the Bosch spark plugs any difference between oem and Bosch or should be good?

@UnicycleWheelie

Жыл бұрын

@@slidin5672 OEM have a resistor

@slidin5672

Жыл бұрын

Do you have to disconnect battery when removing the ecu to get to the driver side spark plugs?

@UnicycleWheelie

Жыл бұрын

@@slidin5672 I would just to be on the safe side

Removing the coil is giving me a problem, can you tell me if this is normal, don't want it to break inside if a i pull on it too much?

@UnicycleWheelie

3 жыл бұрын

some of my coil on plug was hard to pull off, just use your judgement, that is why I used dielectric grease on the boot of the coil packs. they fit very snug

LOL such a nightmare changing spark plugs on this engine.

@UnicycleWheelie

Жыл бұрын

Yeah tell me about it, on my Honda fit, it was a cake walk lol

Do you need to unplug battery. Worried about unpluging wire from computer.

@UnicycleWheelie

3 жыл бұрын

Well, unplugging the battery resets your clock and radio stations, which is a pain. First rule when doing anything to the ecu is to disconnect the battery. Just like any computer you need to unplug it before you work on it

Damn didn’t take off the plenum?!

How do I put that clip back 1:20

@UnicycleWheelie

3 ай бұрын

For the air intake clip, I used needle-nose pliers

Why didn’t you show up all the steps but I guess it is what it is

Tool List Please!!!

@UnicycleWheelie

3 жыл бұрын

Added

@jakesanton2527

3 жыл бұрын

@@UnicycleWheelie Thank you so much! Love the content.

how the fuck did you take off the ecu

@UnicycleWheelie

2 жыл бұрын

Pull up, its snug

I like how they make u take apart the whole car just to do a simple job gotta love Mercedes

@larryreno8293

Ай бұрын

What? This is easy compared to many other manufacturers.

what size socket did you use to remove the ignition coils 2:25

@UnicycleWheelie

6 ай бұрын

E10 socket

@devongrant1076

5 ай бұрын

@@UnicycleWheelie do you use the same size to remove the spark plug itself?

@UnicycleWheelie

5 ай бұрын

Need a 14mm deep 12pt thin wall socket. I used Part # 22814 SKU # 814164 from AuroZone @@devongrant1076

Your better off taking off the plenum and having full access???? It’s 4 bolts and you will have full access to all plugs and coils. ? I get you got to buy 3$ gaskets and swab em if you take the plenum off but shit this is a 5 hour job vs a 2hour lol. Take off the plenum and be done man.