I did the same thing but used a door bell. That way you don't have to remember to turn it of or bumping it on while riding. Just food for thought. Nice video.

@mrjaybennett80

10 ай бұрын

Nice

Just installed new bypass switch and everything works great!!! Saved me lots of $$$ and headache!! Your video is priceless!!

@thomas-gj7pp

3 ай бұрын

Funny how you ended up on this video today like me and the video is 10 years old

I have a better idea, since the relay is there for a reason. A relay is an electromagnetic switch used for controlling high amperage circuits (like power to the startmotor) with a low amperage input (like the brake switch and start switch together to start the engine). Since you bypassed the relay, your new start circut gets hot. Your problem is probably either: 1. Faulty relay, which is easily diagnosed and cheap to replace. jump a cable from power inn on the relay to the power out to the start engine (this is usually the 2 bigges cables on the relay, and the colors is usually, red/red, red/black or black/black. If the start motor turns the relay works. 2. Check if your start button gets power when you press the brake. If not run a wire straight to the battery from the cable that came from the brakes and inn to your start switch. From now on you dont have to hold the brakes for it to start. 3. Now check if your startrelay recives power when you press the start button with a cheap circuit-tester light. Then measure the cable that goes from your start button and inn to the relay, and make sure it recieves power when you use the start button. 4. If you have done the following and the relay neither makes a small "clicking sound" nor do the start engine recieve power, you know it is a grounding problem. Run a wire from your black terminal on the battery to the "probably green/yellow or black" cable that goes out of your relay. your colours on the ground cable may vary so make sure you know which cable is which on your start relay. 5. Now hit the start button again and I promise you that your engine will start to turn. Usually one of the first ting you do is testing your startmotor, but since you showed me that yours work i didnt include testing it as an option. I know that this would be much easier to test with a voltmeter and testing for stuff like continuity, but I am bad at using one and understanding what I am testing. this is a much more logical way to test it for someone who is handy and dont know how to use more advanced testing equipment.

@ps3boss98

6 жыл бұрын

Nikolas Rygh Røren My foreman does the same thing. When i press the start button i dont hear a click noise and nothing happens. The way i start the foreman is by touching metal on the relay. What do i need to replace?!

@landonroiel6695

5 жыл бұрын

Finally someone who speaks English. Yes that's the proper way. rigging up a short cut will not solve your problem in the long run. You always want to do it the right way.

@davidarrieta329

5 ай бұрын

This answer sounds the best option but it is kind of theoretical but I wish I could see something like that in a video Actually I’m trying to fix my atv like that I’m very handy but I don’t want to make any mistakes and get disappointed 😅

Best video I found for what im trying to do. wish me luck

love it how he says how his quad is so small and terrible yet its probably the only quad he owns

How did you wire your ignition/key ? My 110cc wiring is all messed up , and I can get it to crank with the toggle switch, but I need to get spark to the plug, and be able to shut it off using the key. How might I go about doing that ? Thanks

I've been waiting to do this to my motorcycle, I want to eliminate the kill/run switch entirely. Since its in an all in one control, the kill/run and start switch are all one piece, how do I go about making sure the kill switch is always on the run/on position and not on the off/kill position before wiring it this way. I'm going to wire and mount my start toggle switch right below or next to my key ignition switch or somewhere hidden from plain sight

Great Video, Thank You! Can you take the wires from the push button to connect to your switch or do you need to run wires from and to your starter and battery?

FYI you should use a momentary switch.

Can you tell/show me how you mounted the switch please?

i know this is a long time ago, but i have a chinese 150cc atv the dude cut the key ignition wires and used a 16 gauge speaker wire to the stator solenoid and it starts but cant keep an idle and some times it'll do what you showed in your video of just cranking over do you think it could work if i did what you did?

If you have a 150cc sunl atv how do you reg a push button if a gut bought off

hi thinking of doin this did u completly take out the original wier from the starter or join the new and original 1 ??

thanks a LOT this way VERY helpful

hey I just got the quad it's not in to bad cond but I need some help on getting it going

I got a new battery for my sons 125 and when I hook up the positive and negative to the battery the 4 for wheeler starts and try’s to run with no keys in it or whitout ya actually starting it. Can u please help

Anyone know how many amps a typical 100-150cc Chinese quad starter takes, previous owner did this i want to install a relay.

Smart kid, thanks for the help!

I'm having the same problem with a baja 125 I'm trying to connect the starter and the push button is not turning it over

can I do this to a 2003 yamaha big bear 400

Was there a reason that you didn't wire new switch to starter button wires??

Does it start if your engine switch is on the off position

We did u get da bypass button from

Aye bro so the red goes to the battery and where does the only wire go to to the. Starter but where on the starter tho

What kind of wire's and switch?

my atv wont run, yellow start button and red button are broken anyway to by pass all that ?

Right were a brake fluid bubble should be, that screw in

I have a baja 150 with the same problem , thanks for your video , now i can fix my quad , any ideas how to make the lousy suspension that baja has any better ?

@justrigittutorials

10 жыл бұрын

sorry no ideas here about that just kind of adding useful accessories the the 90cc right now but if i ever decide to mess with the suspension i will put a tutorial up on it

Can you please message me on where you got the switch and how you wired it?

My hubby did that to his and nothing happen he has a 110cc sunl ATV what did he do wrong

Is the thick red striped wire that is also runs into the starter with your wire. is the other end of that connected to the solenoid, because im not entirely sure where it should be comming from on mine.

@justrigittutorials

10 жыл бұрын

basically what i did is i attached a wire in the same spot where the thick red wire is thats connected to the starter using a ring terminal that wire then went to one post on my switch the other post from the switch goes to a fuse or fuse holder from there it goes straight to the batterys positive terminal if the switch is grounded it will say (ground) just connect it to a solid piece of metal on the atvs frame or even the negative post of the battery if you want to so when the switch is flipped you will get a light and the starter will turn the engine over but remember that the on switch needs to be to the on position as does the key or the engine will turn over but never start as there is no power going to the coil

Double check your voltages and try charged your battery up till it's fully charged then put battery back in then it will start up with no hassle as that's how I got my quad up running now there no more buzzing sound and if there's a buzzing sound it's trying to tell you charged your battery for sure

i need some help i’m 13 and i’m taking it up to myself and youtube yo fix my bike and i don’t want to mess anything up and i have no idea what to do to not mess up the wire someone help

@lamboking8able

2 жыл бұрын

This comment is a year old. so sorry for anyone being late. did you find out how to do it?

I have the same problem on my daughter's 150cc I'm actually looking for ways to bypass that push button start. It gets really annoying trying to start it

Nice video I like it I do have a question I have a 110 four wheeler that has compression Spark and fuel but will not run have you ever ran into that any information would be helpful thanks

@kingbibble7546

3 жыл бұрын

Try turning the key to the on position then connect a wire to the negative side of your battery touch that wire to the frame where there is bare metal and touch the positive terminal of the battery to the post on the solenoid that is going to the starter it by passes all of these steps to hook up a switch down side is the extra work to start it each time you want to ride

Can you do a full how to please

that screw in piece inside the brake fluid part, where did you find it or get it

@Voartist

2 жыл бұрын

Isn't that the neutral switch so that the engine won't start unless it's in neutral. I replaced mine and old came out of the hole. I didn't know they'd work in oil. But all it is is a switch that's closed by the transmission when it's in neutral. I ordered mine from Amazon, $8.00 and they sent it in an 11x14 plastic envelope. It's only and 1.5" long and .5" wide. Kind of overkill on the packing but I thought it was funny.

Hey buddy I like your video I have a quick question on a Suzuki lt 50cc electric starter I put a new battery and don'ts start what should be the problem?

@theragingslushy

7 жыл бұрын

Henry Alexander Rivas is it in gear, is the fuse blown, bad starter, bad contact, is key on,bad battery

nice that is working good, but why not a momentary push button instead of a toggle?

@solomonlarochelle6389

6 жыл бұрын

jaamzw r

@blaisesarate6729

6 жыл бұрын

Solomon LaRochelle stfu

Hello I have a Chinese 125 four wheeler my son was riding it he hit the kill button and turn the four wheeler off no the four wheeler does not want to start back up I bought a new solenoid but it’s just keep clicking when I try to start it up can you please assist me

What is the part number?

My sister has the same quad! But hers is purple

Im thinking about doing this with my atv. What kind of toggle swtich did you use, and where did you get it from?

@justrigittutorials

10 жыл бұрын

its just a simple on off switch with an extra ground if it is illuminated got it at autozone for like 4 bucks

how is the orginal one ganna work if you cut the wires and wire them up to the switch look I'm 14 years old i start up my yamaha rhino 700 with wires tie up the yellow and black wires together and just the start up wires just make them touch other

@lonnienoland2921

9 жыл бұрын

He is jumping the solonoid,with those thick wires running all the way up to his handlebars. Its not the safest way, for sure, but it works.

Nice video

Was thinking about just hooking up a push button at the start solenoid and bypassing/jumping it there, kinda like how u use a screw driver to jump it. Any thoughts?

@tatchell95

6 жыл бұрын

Roger Johnson I am thinking the same thing? Did you ever do this?

I have it all wired up and when I flip to start it, It cranks but not fast enough for it to turn over... any sugguestions?

@noahwilliams27w46

8 жыл бұрын

Try to charge your battery it's probably pretty low

I need to know how to bypass the start button

Now I have spark to the plug with the key on or off.. how do I turn the key into the kill switch ? I need it to start with the toggle switch and then stay running when I shut the toggle switch off. But the toggle switch is now the start and the kill for the engine. :( HELP !!

@landonroiel6695

5 жыл бұрын

wtf lol

I have the same ATV just a little bit different

I want to no how to wire one of does

I need help doing that on my fourwheeler

yo I am trying to do that but my atv still won't start what can it be and it doesn't turn over for the started

@theragingslushy

7 жыл бұрын

Jorge Hernandez is your starter bad, is your fuse blown, bad contact, broken solinoid, bad battery, suzuki, is it in gear, is clutch not held in? numerous but simple fixes might be the cause

@gekkegeit325

6 жыл бұрын

H2O SLUSHY serious? "Suzuki"??

@texaselite1355

6 жыл бұрын

THE RAGING SLUSHY "suzuki" hahahaha

Nice!

Bro I have a ATV like yours my homie took all the wire off now I can't ride hoe van I start my ATV with out witrs no keys so no ign ????

It works but would have been easier to clean the contacts on the switch

@SirDrakeNewcanon

3 жыл бұрын

Or get a new solenoid too.

@arberfilms5998

3 жыл бұрын

At 0:37 he said he had cleaned the contacts but it didn’t work for a while after.

@lenovo859

10 ай бұрын

I have the same issue replace solenoid and clean switch it work but then stop working so im not sure if it’s the starter switch wanna replace it

@wickerman9569

10 ай бұрын

@@lenovo859 I got ride of mine a few years ago, but it had that remote kill switch on it. I had to take that off of it and ran fine when I got rid of it. Just no more remote kill switch on it.

Can you post a link to where I can buy this button

@VisuFrame

8 жыл бұрын

+Daeton Marcelli You can also use the button from the psu of a desktop computer

What kind of battery do u use for that quad

@landonroiel6695

5 жыл бұрын

They use 12v in these.

also do you know how to make a peace sports 110cc atv louder or any type atv

@justrigittutorials

10 жыл бұрын

no sorry havent really messed with them to that extent yet

@macmuzic74

9 жыл бұрын

just rig it tutorials how u wire it up can u show the steps

My friend has one of these but different design

I have th same problem but I lost my key how can I rig it that way

@kongernedk8428

8 жыл бұрын

+Cole Dancy undplug the key switch

thanks man

I have a 2012 kymco mxu 375 and the start button doesn't work

Can you add a wiring diagram

The only thing is use a toggle switch instead of a regular on/off switch.

Senses u have it bypassed with your switch why would the stock switch still work?

@landonroiel6695

5 жыл бұрын

Lol

@kingbibble7546

3 жыл бұрын

It seems there are no wires too the original switch connecting anymore

Wow thanks.

Thanks

I need mind to wire plz

Can u help me out with on

Can u show me a diagram for this plz

we're can you buy that switch

@charlottejackson6360

8 жыл бұрын

where to get a switch like that from.

@landonroiel6695

5 жыл бұрын

Walmart or any auto parts store

I need some help

Wrong switch friend, use a push release button and don't by-pass the relay or you will burn the harness ,there are two wires that give command to the relay the two thin ones,find which one is your hot wire and thats where you can connect your button...good luck

just wire it into the starter solenoid that way you dont have all that high current going to the switch

@everardoplancarte4178

4 жыл бұрын

How you do that?

okay .... so why didnt you put a solenoid inline so ALL THE CURRENT... DIDNT go through the switch and make it hot.... i guarantee the contacts in that switch will wear out like crazy...

There was no wires cut

No my starter bottom does not work

@rperry209

6 жыл бұрын

John Araniva n

What he's gonna do if he leaves it on he's gonna burn up that fuckin starter

I like to show a good video on bypassing that Chris Brown

I wish you would have figured out how to wire the proper start button, because I think I could have actually learned from you. Every video wiring these atv lacks too much to actually help.

Aye that's my first atv I got it when I was 4 and now I'm 16 and I drive a Honda 450r

I have the same color

Instructions how

Neat, but the only problem I foresee is bumping it while riding and shredding the starter to pieces.

It's a clutch not a break

Don't do this, spend the money and buy a new switch

@calebproductions5970

4 жыл бұрын

Why? This works too.plus, dont have to rig up that safety switch.

Hey can u teaching me wire code

How about fixing stuff the right way? People always want to half ass stuff. Love the comment "make sure to cut off the switch or it will burn it up" how about it will burn up the starter. Fix the mess right and you won't have to worry about it burning up the starter or the rigged up toggle switch

Your going to burn your starter like that

your old starter is burned out to get a new one it will cost 70 to 90 dollars

@justrigittutorials

10 жыл бұрын

the starter is fine it was the push button starter that went out

dont doo this if you are do it right use the factory solinod

Fake when he used his original switch his kill switch was on so no shit it wont start

you are destroying ur starter faster unless u are ready to turn of the switch.

where is the tutorial? I suggest getting a tutorial on tutorials

What's a baha I thought it it was a ba-an-ge(Baja) but thinks for the tips bud

@texaselite1355

6 жыл бұрын

Chrissy Johnson nope baha(baja)

If the while got burnt off

horible

Hey i need help starting my bike