My recliner was stuck in the up position and this excellent video help me eliminate the motor, the wiring harness, and the power supply. Thank you for posting.

Excellent! I picked one of these up as part of an estate sale auction lot and wanted to make sure that it worked first in order to sell it. I was about to buy a used controller for that but you saved me the coin. THANK YOU!!

Thank-you. This eliminated the motor and power supply as problems.

Hi Saul, this video helped me with my issue. Thanks.

Thank you Saul! Very helpful!

Thanks for this. I just had both of my recliners stop working on a 3 year old couch and they both died within 6 months of each other. If I plug the power supply in, the light on the power supply immediately goes out as if there's a short somewhere. I then pulled the 5-pin plug that goes to the switches and the power supply will stay on and not go out (leading me to believe there is a short in the switch). I then did what you showed in this video and jumped the pins and was able to get the recliner to work both ways! I now ordered replacement switches. Thank you so much for this I was trying to figure out which connectors to jump when I came across this video. Perfect!

@germanywho

Жыл бұрын

did the replacement switch work iam having the same problem? but I don't want to waste my money? and where did you get the replacement part?? THANKS 👍🏾

@Mudslidex1

Жыл бұрын

@@germanywho yes. I actually just made a video on it and going over how I did it. Links to the items are in my vid description too kzread.info/dash/bejne/l3eTs8-Mlsy5mso.html

@pschweiss

8 ай бұрын

Exactly as you describe for my situation on a Costco recliner. This Video enabled me to validate that the motor was good... off to buy a switch replacement. Thanks everyone!!

Thank you!! This is exactly what I was looking for.

Thank for sharing this very helpful information 😊

Thank you! This was a life saver!

Thank very good trick and useful to fix stuck recliner

So I pulled Okin lift chair motor out... I put wires in like described. Not get getting anything. It does have solid power. Unless I'm doing it wrong... Thoughts... What are you ground it to. The video doesn't show clearly...

Hello Survivor I am making a diy router table with a drill & I don't have a slid rail. I just have this recliner deal I snatched off a sofa in the boonies to flip. Never did flip so I will be using the to rais the drill as is my router do trim custom crown trim. I was thinking maybe splice cable to a DC v 12 /9 really ill just be lowering it few times to change out bits. Thank u for video Happy 2022

Thanks for the video. Can any five pin remote work on any five pin chair?

Hi can i use any wire as jumper?

Thanks for the info.

My recliner has control buttons located on the armrest cup holder. The led lighting, USB, and headrest control works but the recliner button does not. Is it a to/from connection to the button in the armrest?

Excellent, thank you

Interesting thank you. Lol Dad and I are looking at this now

What if you black connector to your power supply comes loose and your red connector still connected i had this happen how do I fix that

Thank you for video

and khe key offe Hey look can u tell me 9n a modld 3513 the green wire with fiuse witch pronge on the male receptacle on the chair if the ground is the bottom pronge?

Hey do you think you could help me find where some wires go on our chair. They fell out when we moved it. It looks like it’s from a motor like the one in this video

SO IF THE SWITCH IS BAD WHEN YOU HAVE IT PLUGGED UP RIGHT DO THE GREEN LIGHT ON POWER SUPPLY GO OUT?????

Where did you find the schematic for the 5 pin din identification?

So I bought a jumper wire set and tried several of them with no results. Does this mean the motor is shot?

Good job

I have a switch on our massage chair that doesn't work properly. How about a video on bypassing the that switch?

Perfect. Thx

My client ended up pinching his cord in the chair to the point of exposed wires. I changed the power supply, and the transformer has power. The remote has power, but the chair does nothing. So maybe Ill try this to see if it works. Unless you have any other suggestions or know what might have happened

Do you know how to disassembly that motor? I guess internal relay is broken.

Do you know of a way to increase/decrease the speed of these motors?

Mine is a 7-pin connector. Any help is appreciated and I have a picture of it.

I was able to jump it and the motor works. I purchased a new switch and it didn’t work. I figured that maybe the new switch was bad so I ordered another but again, no go. What do you think is going on?

Ok I got it to open, which i actually wanted to keep it closed. So now how do we reverse this role?

@Charlax21

2 жыл бұрын

Jumper from Hot (Pin 1) to Pin 3. Jumper from Pin 2 to Ground. Observe which direction it goes. If it goes in the wrong direction, then reverse it and do Jumper Pin 1 (Hot) to Pin 2. Jumper from Pin 3 to Ground.

@den-mar9621

2 жыл бұрын

@@Charlax21 thanks so much had same problem wanted to go other direction. Got it great? Great ?Awesome answer. Thanks again

@jonsarabia2587

6 ай бұрын

@@Charlax21exactly what I needed, thanks!

Can I wire DIRECT TO DC power without using the ac power cord?? I'm wanting to power the recliner in my RV from my 12 volt system.

@danieldorchester5221

Жыл бұрын

You should already have a battery back up in the power supply. It’s usually on the side with a couple of 9 V batteries you could wire a battery power supply into the side of the power supply without any difficulty.

@pushbroom9398

Жыл бұрын

@@danieldorchester5221 thanks have a BLESSED Memoria weekend l

I can't fine what I want on Amazon no were..I need one just like what they showed in this video my slide arm is only 8" long.

Do you have a circuit diagram?

What gauge wire did you use?

My seat works one way. I put jumpers and nothing happens. Now the chair is in the supine position.

Tried this at first it was working and then I think I did something wrong and there was a spark and then it no longer worked do I need to replace the motor now?

@karlwondra8960

Жыл бұрын

The green wire hot attaches to witch mail pronge on the plug in if ground is positioned on bottom

@karlwondra8960

Жыл бұрын

On a modle 3513

@karlwondra8960

Жыл бұрын

The 1 with the fuse holder

@karlwondra8960

Жыл бұрын

Put

How do i get it back in again?

wonderful thank you so much

Hi. I have an Okin JLDQ - 1A actuator. I can test the motor is OK and I know the switch is working buy something it preventing the motor from working. Power is getting to the actuator board but I am stumped after that and your 5 din connector video works differently to my model actuator. If it was OK with your I'd ask for advice. I created a document that explains everything with images. Anyway if you can PM me I would be grateful. Thanks.

A mi sillon le falta el cable de poder Y no encuentro en ninguna parte el reemplazo Como puedo adaptar uno Me ayudas por favor

Where do i get a jumper plz? Im trying to fix my (former) MIL chair. And after accidentally electrocuting myself im scare to try this

Where did the purple wires come from?

@michaeltree5469

2 жыл бұрын

Any small wire will do. A metal paper clip (with no fancy coating) will work just as well if you have no wires.

@gs2628

2 жыл бұрын

@@michaeltree5469 Won't you get shocked, using a paper clip with no coating? 🤔

@timh6837

2 жыл бұрын

@@gs2628 most cases this is low voltage DC after the transformer which is finger safe

Didn't work for me. My motor must be shot

Friend..we can't even SEE what you're trying to demonstrate...

This is written as if all recliners use that configuration and everyone has as wiring schematic. If you have the wiring schematic any first year electrical student can run a jumper. Now as yourself how many pieces of power furniture come with a wiring schematic. Sorry but pretty much a useless video which assumes everyone has the same equipment and a wiring schematic as well.

How much for a rising recliner arm as pressed the button when looking underneath and it broke product I'd nu 745obxgn motor serial no 0645wp