Building the CubicFun 3D Puzzle of the Notre Dame de Paris - 1
You guys can look over my shoulder again as I build the 3D puzzle of Notre Dame. CubicFun has 2 puzzles of this beautiful Cathedral. This is the big one; scale 1:250.
Make no mistake: it is quite a spicy kit. In this 1st episode I show some techniques, which I go over more quickly later in the film. In particular, placing the stained glass windows can be quite tricky at times. Sometimes the printwork at the parts, which have to be punched out for placing the windows, is not accurate. As a result, the windows do not fit exactly and you have to cut the plastic strip into separate parts to make the windows still fit neatly. Furthermore, you have to pay very close attention to the small details in the construction manual. Otherwise, you will have problems later during construction.
I hope you like the video. And if you are also going to build this puzzle: have fun building it and good luck.
Jullie kunnen weer over mijn schouder meekijken, terwijl ik de 3D puzzel van de Notre Dame bouw. CubicFun heeft 2 puzzels van de deze mooie Kathedraal. Dit is de grote; schaal 1:250.
Vergis u niet: het is best een pittige kit. In deze 1e afleveringen laat ik enkele technieken zien, waar ik later in de film sneller overheen ga. Met name het plaatsen van de glas-in-loodramen kan soms best lastig zijn. Soms is het printwerk bij de delen, die uit-gestanst moeten worden voor het plaatsen van de ramen, niet nauwkeurig. Daardoor passen de ramen niet precies en moet je de plastic strook in aparte delen knippen om de ramen toch netjes te laten passen. Verder moet je heel goed opletten op de kleine details in de bouwinstructie. Anders krijg je later tijdens de bouw problemen.
Ik hoop dat u de video leuk vindt. En als u deze puzzel ook gaat bouwen: veel bouwplezier en succes.
* Nederlandse ondertiteling beschikbaar.
Du kannst mir wieder über die Schulter schauen, wenn ich das 3D-Puzzle von Notre Dame baue. CubicFun hat 2 Puzzles von dieser wunderschönen Kathedrale. Dies ist das große; Maßstab 1:250.
Täuschen Sie sich nicht: es ist ein ziemlich pikanter Bausatz. In dieser 1. Episode zeige ich einige Techniken, die ich später im Film nicht mehr zeige. Vor allem das Anbringen der Glasfenster kann manchmal recht knifflig sein. Manchmal ist die Bedruckung der Teile, die zum Einsetzen der Fenster ausgestanzt werden müssen, nicht genau. Das hat zur Folge, dass die Fenster nicht genau passen und man den Plastikstreifen in einzelne Teile zerschneiden muss, damit die Fenster doch noch ordentlich passen. Außerdem muss man sehr genau auf die kleinen Details in der Bauanleitung achten. Sonst hat man später beim Bau Probleme.
Ich hoffe, dass euch das Video gefällt. Und wenn ihr dieses Puzzle auch bauen wollt: viel Spaß beim Bauen und viel Glück.
* Deutsche Untertitel verfügbar.
Пікірлер: 26
Thanks for the helpful tips!
@leokessels88
Жыл бұрын
You're welcome. Thanks for watching.
"Dies ist das große; Maßstab 1:250" Das sieht man. Die Kathedrale wird ganz schön groß und sieht jetzt schon klasse aus. Es macht Spaß zuzusehen und Appetit, es selbst zu bauen.
@leokessels88
Жыл бұрын
👍 Nun, dann wünsche ich einen guten Appetit 😊. Aber sei vorsichtig, wenn du etwas kaufst. Ich habe dieses Puzzle vor einiger Zeit für 50 Euro gekauft, aber im Internet liegen die Preise jetzt zwischen 55 und 150 (!?) Euro. (Fortsetzung folgt in Kürze. Ich bearbeite gerade die Videos von Teil 2 und 3)
@models-by-fadda59
Жыл бұрын
@@leokessels88 Danke für die Warnung, das hatte ich zum Glück schon bemerkt. Auch die kleinere Version wird teilweise mit den Bildern der großen Version angeboten (von offensichtlich zwielichtigen Versendern). Ob ich diese Art Modellbau auch noch anfange, weiß ich aber nicht. Erstmal schaue ich dir zu. 🤜
@giovannicapizzi3998
Жыл бұрын
Habe sie mir heute gegönnt 😊
France 🇫🇷
The insertion of part 207 makes no sense in relation to the other parts. I cannot figure it out.
@wcombs
Ай бұрын
Actually it’s part 96 that makes no sense. It doesn’t stay on.
@leokessels88
Ай бұрын
Part 207 is the part to stick the round rosette window on. It gives depth to the windows and also provides strength to the center part.
@leokessels88
Ай бұрын
@@wcombs This component also provides the depth effect. But you have to follow the right order of installation: first slide part 102 into 212, then insert 95 (with the windows) and finally 96. Then everything will stay nicely in place.
@wcombs
Ай бұрын
@@leokessels88 I figured it out. It wasn’t until the next few steps and pieces went in and held everything in place.
I also want to know what kind of ruler you used for the construction of this model.
@leokessels88
10 ай бұрын
I have several rulers. I normally use one made of metal. But this was an ordinary plastic ruler I got as a business gift.
@curtisspratte-lennington2311
7 ай бұрын
I just bought a square file tool set. I'm thinking about starting my Notre Dame Cathedral set sometime in February or March whenever I feel ready. Do you have any tips or recommendations for this model kit? I'm concerned about placing the stain glass windows properly in place. I will use your video tutorial for help. Thank you.
I have a question: what type of square file tool did you use?
@leokessels88
10 ай бұрын
As you can see, it's just a small square metal file, like those that can be bought in a key file set at the good hobby store.
Pretty cool but not what I would call a puzzle.
@leokessels88
7 ай бұрын
Depending on their skill and insight, this will still be quite a puzzle for some 😄
I just wanted to write and say thank you very much for the detailed walk through of this model. I literally just started, and I am at 2:37 in your video, and find that the instructions provided are pretty bad in my opinion. They do not do a good job explaining what side is the viewable side versus the side that you apply windows to, or the side that is the "backside". I would have been lost without your videos. And I am not new to advanced models. I've built many complex polystyrene models, but these just do a poor job at explaining. Thank you again, much appreciated!
@leokessels88
Жыл бұрын
Thank you for the compliments. I always enjoy reading that my videos are helpful. By the way, I had run into the same problem with the windows and the poor building instructions. Fortunately, I had experience with installing printed windows with Metcalfe's card construction kits. You will find a few videos of these on my channel as well. Have a great time with your building projects.
@TrekBuilder
Жыл бұрын
Thank you, I am catching on, and I find it just extraordinary the level of detail in this kit. The engineering that goes into these leaves me speechless. I am really having a good time with it. I also bought the Saint Paul's Cathedral, and the very large Sagrada Família Moveable Church, though that one I had to order from Cubicfun directly.
@curtisspratte-lennington2311
10 ай бұрын
I've got a question. When it comes to putting the windows in place do you place the windows in to where the code on the window is facing in the opposite direction as what it looks like in the video? Because otherwise I can understand to where to place the windows which is place it to where the glossy reflective side is facing outward.
@leokessels88
10 ай бұрын
The printed numbers are on the glossy side (which was covered with the film). The double-sided adhesive tape should be stuck on the glossy side because the glossy side of the window should face outwards. So the double-sided tape should be stuck on the glossy side. I think I did it this way in the video.
@curtisspratte-lennington2311
10 ай бұрын
Thank you for the response. It's just that when I saw the video it looked like the codes was facing backwards.
love life