No video
Build your own ladder hoist with 24'/32' ladder and 800lb hoist/lifter
2 - U-BOLT ZINC 5/16 X 5-3/8 2X$2.05
2 - EYE BOLT/NUT ZINC 3/8 - 5 2X1.10
4 - HEX BOLT ZINCE/NUT 1/2 -1-1/2 4X$0.99
4 - 1/2" FLANGED BEARING 4X$2.50 (XiKe BEARINGS) from Amazon 1/2" x OD 1-3/4" x Width 1/2"& 7/16"
5 - Partsam 440 lbs Lift Electric Hoist Crane Remote Control Power System, Zinc-Plated Steel Wire Overhead Crane Garage Ceiling Pulley Winch w/Straps (w/Emergency Stop Switch)
Пікірлер: 31
Nicest one I've seen yet.
@jq3291
Ай бұрын
❤
Thank you! The inside of my bracket’s measurement is 1 13/16.
Great job I'm building one just like it I have watched this video several times
very clever design. you should consider applying for a patent and selling design to Werner for a few million.
Nice build. But, you probably need to replace the top rung of the ladder with square steel tubing maybe 1/8" thick. Otherwise, with any load the top rung will bend and eventually break.
@akaredcrossbow
Жыл бұрын
If that’s the case, then anyone over 150lbs going up the ladder would break a ladder rung. If he doesn’t go over the weight limit of the ladder it should be fine. Maybe for piece of mind put a solid piece of angle across the top so it doesn’t pull in on itself. If your lifting anything 100lbs or under it should work flawlessly without damaging the ladder imo.
Awesome job. Something to think 🤔 about. Great job 👏
Thank you for posting … best diy lift
Im inspired by this design 😮
Very clever design!
Great share!
Great job!
With the ladder at that angle sitting on concrete if you lift the shingles past the fascia it will kick out. Nice design tho
@jesusisaliberal548
2 жыл бұрын
Nice job! Need to set up ladder at 75 degree angle for maximum stability and safety
Thank you for sharing.
Nice Job... How about some links to where you bought parts....
@0202hcauq
3 жыл бұрын
I bought these parts from The Home Depot and the lifter from Amazon. Have fun with this project.
It is true that you can only use it in a period of 2 minutes and you must let it rest for a period of 8 minutes to be able to use it again.?
@0202hcauq
Жыл бұрын
No, it is not true. I can use it for one hour without resting.
Would you be able to post a link to the bearings you used from Amazon?
@alonzoarcher6585
Жыл бұрын
Oops..I see you put it at the end of the video.
How do you remove it when you finish and how to mount it when you need it?
@0202hcauq
Жыл бұрын
Remove four nuts secured the hoist then unhook cable
What do you do for a 2 story home
@0202hcauq
Жыл бұрын
You can buy a longer ladder.
@7628739
Жыл бұрын
@@0202hcauq I understand that but how do you join the 2 ladders together to climb up on the rails
@0202hcauq
Жыл бұрын
@@7628739 I am sorry I don't know. I saw they sell a 30' ladder with a hoist for around $2500.
@abacab87
Ай бұрын
You'd have to buy a 40' ladder. I use a 40' ladder for a scaffolding plank I put a 20' wood plank on top. I just wouldn't have more than 1 person on it at a time, but that's all I do for professional planks as well. It's always been very sturdy and I can do a 40' walk way near the roof edge.
What hoist did you use sir?
@0202hcauq
Жыл бұрын
Partsam 440 lbs Lift Electric Hoist Crane Remote Control Power System, Zinc-Plated Steel Wire Overhead Crane Garage Ceiling Pulley Winch w/Straps (w/Emergency Stop Switch) or You can get a cheaper from Harbor Freight