Thank you William for sharing this simple jig. I built it a few weeks ago and already it is indispensable.

Your videos are the very best and I always view them. My table saw sled is dead on thanks to you. I wish you were closer to me as I would love to take your wood working class. Thanks again.

Good to have you back! I use a lot of composite flooring for table saw jigs. It's very dimensional, durable, slippery, and easy to work. Use plywood and pine to hold stuff together, but I haven't found any affordable alternative that works as well.

Thank you! I’m very glad to see you making videos again, yours are among the very few for which I will stop whatever I’m doing to watch as soon as I receive the notification.

Just wanted to thank you for posting this. I put it to good use recently when I put 1/2 wood strips around the perimeter of 10 cabinet doors to match some 70 era cabinet doors made with lumbercore plywood with a finger pull edge all the way around. You have made a great contribution to woodworking with your channel. Thanks.

I made this yesterday for my cheap Aldi Table Saw and am delighted with the outcome. With regards to clamping, I don`t have a long reach clamp so, I cut extra strips of the narrow wood and slotted them into the top space between the faces at 90degs - this enabled me to use my clamps without worrying about them pulling the `face` out of 90deg to the saw bed. Thanks for the vid

Another great video. We find that a slight angle on the nail gun when firing nails creates a dovetail effect preventing any risk of nails pulling straight out. Hope that helps.👍

I just love your videos, thank you for making us smarter, and better woodworkers 🙏🏼

Mr. Ng is a very good woodworker that knows what he says. He is very precise and great as a teacher. I respect him and what he says.

I thoroughly enjoy your videos. The instruction is clear and accurate, and your projects are beautiful. Your sense of humour is fantastic. Love your work all round.

LOVE your subtle teaching style. You are a true treasure William. We wait a looooooooong time for these jewels, but i do better work because of you.

Thank you for your videos. They are very educational and I enjoy your sense of humor and wit!!

I’m going to make my fence tomorrow. Thanks for sharing your experience!

Thank you for the explanation. And welcome back you have been missed by many my self included.

I can't wait to watch this later. I absolutely LOVE your attention to detail. Been so long since you posted videos!

OK I'm hooked. Been watching your vids all day. Extremely smart man with a great sense of humor.

Beautiful work. Love the thought process and methodical attention to detail. Seems like maybe you've done this before!

Great video William. I appreciate you taking the time

Mr. Ng Yours are the most entertaining and informative videos that I watch here on KZread. I look forward to each new video but I also watch whatever pops up, such as this one. I know I’ve seen this one several times and I enjoy it each time. Thank you.

Good to see you back,, Phil.

Great video. I made a new table saw sled using your method, the sled is dead on accurate. Thanks

So clear and calm makes it sound a joy to do 👍

Hello Mr. Ng, you have really opened my mind up to so much more about woodworking. Your videos are very educational, cover so many aspects of operating a great shop and also very entertaining with your smart humor. I hope you are able to post more content as I really enjoy and appreciate your videos. One day I’ll work up the courage to sign up for one of your classes since I’m local. Take care my friend and be safe!

I agree with Mr Burke . Another great video William ! Thank you !

I like your sense of humor and all your videos. Thank you for your knowledge and Happy New Year !

The whole of my shop is about the size of your table saw ! Great tips thanks fr sharing

I made this jig. Works great, nice idea so simple Save a lot of time when moving from the table saw stop to this jig

Outstanding vids William. MUCH appreciated.

I truly appreciate your attention to detail. Thank you

You sir are a true craftsman and a fine gentleman. I hope the new year treats you well. :)

@tomzettel105

6 жыл бұрын

I agree with you Mike!!! Tom from Canada

@mrfixit1121

6 жыл бұрын

Don’t judge him

Wow. Accidental ran across your videos William and subscribed immediately. Had the pleasure of taking one of your classes a good while ago and it really opened my eyes to what was "fine" woodworking. I would highly recommend them to anyone interested in refining whether new or experienced. Glad to see you are doing well. Regards, Philip K.

Awesome! Happy New Year to you my friend!

Your videos are great and your precision is off the chart!

as always William, very good and helpful video thanks for posting, from Garry in the UK

I always enjoy your videos and also your humor. Thanks Blessings

Perfect, BTW a nice workshop and very clean. greatings from the Netherlands

Always love your videos! Thank you for sharing!

Great video! Keep up the good work! Also like the funny remarks "Hand model!"

Very nice build and excellent video with clear directions. I especially like the little segment on your Felder Saw. My Delta Unifence rail is almost identical (in shape, at least), so I now have an option for some fence upgrades. The fence is very accurate, but the shape limits the add-ons. Thanks much for the tips. Just subbed your channel. ATB

The best woodworking instructional videos on the web. And the jig is tops too. Built one for my Unisaw a year ago and it's great.

Hey Mr. Ng! I really love your videos and love how well you explain things so it's easy to learn! I was wondering what would you do if the fence sides weren't square once you clamp it up with the big clamp and before you nail it?

Great video, I'm looking forward to building one of these for my saw! Thanks!

@briancammarata4869

6 жыл бұрын

Ted Sherburne I

I really love your videos always learn something new, great job.

That was all good information and fantastic workmanship.

Excellent work, I really enjoyed watching it.

William....thanks for the HD re-post. HNY

Very happy to see you again on making videos! Love them. Happy new year!

@josephbedard6230

6 жыл бұрын

Thanks so much for the new video. I just finished my new crosscut sled,and this will be a good addition to it. Thanks for sharing this with us.

Great video! Glad to see you back making videos again!

I, too, am a hand model when I am not painting homes. I wonder what do you do to keep your hands so soft? Any secrets? Palmolive? Bahhhaaaa!!!! Thanks again for sharing your art!

@wnwoodworks

6 жыл бұрын

HaHaHaHa Thanks for the laugh

Another great video. Very good instruction.

For a guy who measures wood with dial calipers; it is impressive to see you say that a small gap in a glue up "doesn't really matter" when it's a non-functional dimension. I wish more people understood that slop makes life easier when you have the room for it.

William, I very much enjoy each one of your ‘how to’ videos. Always precise. I e learned very much. In this video you made a small reference to cutting the rabbet ( 7/8” x 1/4”) in the fence jig. Is there another video which I ve missed where you provide more detail on its use/application? Thank you.

Great video! Thank you for taking the time to make these videos for us. It is much appreciated! And, you are hilarious 😂 😃

Like your videos. Very Helpful. Also. I was in the Marines with an Ng. Amazing Marine to look up to...Probably no relation to you but found your name as a great Memory...

Thanks just getting ready to make a cross-cut sled. This will be a nice addtion.

I like your table saw setup.

Great videos William. Thank You. How many inches of clamping throat do you need for a 7" tall jig? If the tick mark is 3" up wouldn't 4" or so be enough?

06:31 "and don't you do judgment" jajajajajajajajajjaja you always make me laugh. Greetings from Roma, Italia!!!!

You do make me laugh. Refreshing videos.

😆Hand model✋ Thank you for sharing your knowledge and humor. ❤🔨

I built this about 7 months ago. I'll never trim edges any other way ever again!

Thank you I learn something to day.

Excellent video!

Thanks so much!

William the Magician. Thanks. PS like your comedy too.

Great video as always Cant wait to see more ....well done

Great video, thanks!

Yay! I love your videos William! Thanks for sharing with us. p.s. I've always thought I could make it in the hand modeling field. Can I get your agents name? :-D

That's NgGenius™!

About the glue up, do you think a strap clamp around the middle would work if we don’t have deep clamps like yours?

Good job ... for a hand model

Very clear video. Thanks. :)

Great movie! I did it also with nails and realized that im not a pro like you lol! It was not square so i did it again :)

Anyone know where those deep clamps can be had?

My original fence got wet and was not salvageable, I tried to attach an H style fence by screwing self tapping screws into the square tube which gave me a good solid connection but not square. Would you think removing it and building a floating one like this onto a square metal tube only about an 1 1/2 would give enough stability? I'm not sure why you made the dado at the end does it reference from another video?

Nice work, as always, William. Since I have a Delta Unifence, I adapt differently. Maybe some day I'll change it for a Biesemeyer but after 25+ years I have designed various jigs for my fence that serve me well. Most proud of my simple mortise and tenon jig built from scrap wood and PVC board, except for a pair of hold down clamps. Unrelated to this video - and hope you are still monitoring this - what brand/model is your roll-up extension cord? From various videos you've done, it appears that you have had at least two different ones. I've looked at some big-box products but all have bad reviews and too-low amperage (16- or 18- or 20-ga. cords). I'd want to cover 15-amp circular saws, sanders, etc. that will last a good many years. Thanks.

Nice jig, I will make sure to build one when I get around to finish off my table saw build. I do have one question though, you use the diagonal measure of the fence front / back as the length of the jig and then you added 1/8" for movement, why did you use the diagonal measure and not just the straight length measure? If you add 1/8" to the length for 'slop' then why not just use the real length + slop?

@ianmathieson65

4 жыл бұрын

The clue is in the shot where he fits it over his existing fence. He lowers the far end of the jig first, until it rests on the table top, then lowers the near end. It therefore has to clear the diagonal length of the fence with a bit of clearance to make an easy fit. If it was sized to suit the horizontal (non-diagonal) length, the added 1/8” may or may not be sufficient to allow it to be fitted and removed in this manner. Without adequate diagonal length plus clearance, it could only be fitted by carefully lowering it down while attempting to keep it approximately horizontal - a much more ‘fiddly’ task. And the same applies to removing it. Taking the method of fitting and removing it into account is a mark of the genius that William is.

Well done.

Thank you for your videos William, I like your work and I’m looking forward to building some of your jigs especially the mitre sled & fence jig, I have a question which I’m sure I know the answer but just need you to clarify, the last cut you did on the multi function table saw jig is it to create a chamfer so as to get a perfect reference without out saw dust interference and not quite sure what you did( how much and did you tilt the blade? Thanks Kyle

@wnwoodworks

6 жыл бұрын

Hey Kyle, I made a video earlier explaining all the different uses for the jig and why I cut the rabbet on the jig. Here's the link kzread.info/dash/bejne/c5iYqpqCl6-dp7w.html

@kylecroft5807

6 жыл бұрын

Thanks William, really clever application. Definitely going to make this.

Nice Job!!! You sir, are a joy to watch and from which to learn. Question: Why did you cut a rabbit?

@wnwoodworks

6 жыл бұрын

i made a video earlier explaining all the different uses of the fixture. Here's the link kzread.info/dash/bejne/c5iYqpqCl6-dp7w.html

@septimuspretorius250

6 жыл бұрын

Thank You!

Wonderful

you are the Jackie chan of sawdust, love your videos

@jeremyvaughan8616

4 жыл бұрын

Hahahha I was thinking the same thing when I was watching this video! 😂 Great man and great informative videos!

Idea: One can make a push stick, that hooks over the custom made fence.

I enjoyed this video so much that I had to subscribe. Thank you!

I find myself frequently mumbling, "That's a good idea!"

Freaking brilliant

A Super hand model LOL nice video.

can you / would you use this as an upgrade to the fence that comes with a contractor saw? I have a Rigid contractor saw, I have not been able to justify the expense of a full-size table saw as a beginner woodworker. The fence on my Rigid is not rigid at all and usually, the outfeed end is 1/16" to 1/8" off of the infeed end. any help would be greatly appreciated.

@leonardorojas1781

6 жыл бұрын

Rafael H What did you do about the fence of your table saw? I have a cheap Stanley table saw and its fence is its weakest part because it's never parallel to the blade by itself. I'm looking for a design of a fence that I can adapt to my table saw. I think I just got a couple of ideas from this video.

@francisgoulart5648

5 жыл бұрын

Did you check the owners manual, usually the fence or the saw blade itself has an adjustment.

Instead of making it close to 0.002" the width of the fence, I think better is to make it wider, to 0.02 inch for easier fitting. Cut two 2.5 to 3 inch holes in conjunction with two holddown (or toggle) clamps for clamping. Then it will be a tight fit without the need to limit back and forth movement, due to friction.

When determining the length of you fence, why do you measure your original fence diagonally?

@richardpatterson4312

6 жыл бұрын

MrSawdust85222 I think so he can drop it on as shown. otherwise it would bind. He could have said just add an 8th to the length but if you had a tall fence that wouldn't be enough. Unless I'm wrong, in which case I want the answer as well.

@MrSawdust85222

6 жыл бұрын

Right, after thinking about I figured it out. Has to do with the arc when installing it.

Thank you for your informative video, I know it has been a while since you made the video, I have a question, is your Fence Jig supported on the fence? or is rubbing on the table? my fence is similar to yours, but far end is supported on nylon blocks that run on an angle attached to the Cast iron top.Thank you in advance. Kind regards and keep well Jack Marashlian from OZ

@garrettswoodworx1873

3 жыл бұрын

You've probably figured this out already but in the video he mentioned the reason for the spacer he put between the top of the fence and the "top" of the jig while measuring and assembling was so that the jig would ride flat on the table and not be held up by the top of the fence. Hope all is well "down" in OZ!

@jackmarashlian2463

3 жыл бұрын

@@garrettswoodworx1873 Thanks you are correct. jack Marashlian

I have a vintage 50s Craftsman contractor table saw. Should I do something to make the original fence wider before I add this?

@wnwoodworks

6 жыл бұрын

I'm not familiar with your saw but if it's thin like my Felder then I think you can do the same and customize it to your saw. Not sure how you can widen your saw. Hope this helps and best of luck.

@bmilhoan

6 жыл бұрын

I'm sorry to be unclear. My fence came with a piece of old counter top bolted to it. With the assumption that wider would be more stable, and noticing your fence is at least 6-8 inches wide without the frame around it, I wondered if I should bolt something on the fence to make it wider; perhaps a section of 2x4. Then a frame similar to the one you built would be wider and more stable. I've never owned a table saw so I was guessing at this. Thanks for your great videos!

Great job there! Why do you need a groove on the bottom (rabbit) of the front ?

@wnwoodworks

2 жыл бұрын

I have a video showing the different uses for the fence kzread.info/dash/bejne/c5iYqpqCl6-dp7w.html 6:40

@rogerboucher1913

2 жыл бұрын

@@wnwoodworks thank you for the quick response. Now I know! That will be very useful for me and a much safer way to trim. I sympathize for your lost. I also lost my mom, she was 94 1/2. I miss her.

@wnwoodworks

Жыл бұрын

Sorry for the late response but here the video explaining the use. kzread.info/dash/bejne/c5iYqpqCl6-dp7w.html

Nice build, where do you get those deep throat clamps? I have been looking for them for pressing inlays in my cutting boards and the deepest I can find are​ 5 1/2. Where did you find them?

@ewoid64

6 жыл бұрын

One place is the Bessey Clamp CO: www.besseytools.com/en/product_details.php?ASIMOID=000000010003892e00020023&ASIMOID_SC=000000000001f21d00030023&ASIMOID_MC=000000000001f3f000030023

Oh, God!! You are..God!

Why the rabbit cut? Is this to handle the saw dust when cutting stock against the jig?

@wnwoodworks

5 жыл бұрын

It's for flush trimming. I have a video explaining all the different uses. kzread.info/dash/bejne/c5iYqpqCl6-dp7w.html

11:05 "♪ Cut the rabbet, Cut the rabbet, ♫ Cut the rabbet! ♪" - Elmer Fudd

@wnwoodworks

6 жыл бұрын

HaHaHaHa Isn't it more like wabbet, Cut the wabbet.

@pmdinaz

4 жыл бұрын

@@wnwoodworks unless its in the U.K. cut the weebate...cut the weeebate Miss your tutelage

What material did you use for this jig?

@wnwoodworks

2 жыл бұрын

3/4" Baltic Birch Plywood

Just wanted to wish you a great new year in 2018.

I need to make my portable saw fence better