Build a High Power Amplifier Using 20 Transistors - MICRO BOOSTRAP with M-270 BOX
Ғылым және технология
PCBA from $0(Free Setup, Free Stencil): jlcpcb.com/DYE
Hi friends, in this video I try to make a high power amplifier. This amplifier consists of 2 channels (stereo). Each channel uses 5 pairs of end transistors (2SC5200 & 2SA1943).
In this assembly, I only used a 5A 47VAC transformer. But this amplifier can still be upgraded up to 10A 55VAC (if using the same box). The total budget for this amplifier is around $120.
Instagram:
/ cbzproject
Facebook:
/ cbzproject
#Amplifier #AmplifierBuild
#StereoAmplifier #PowerfulAmplifier
#HighPowerAmplifier #PowerAmplifierBuild
#cbzproject #StereoAmplifier20Transistor
#20Transistor #HowToMakeStereoAmplifier
Пікірлер: 524
Full Assembly High Power Amplifier with Toroidal Transformer 70v 0 70v👇👇 kzread.info/dash/bejne/dqdtt9KuoLfactY.html
[NEW] Build a high power 4-channel amplifier: kzread.info/dash/bejne/oaCFl9B-qZq_lNY.html
Couple of observations: 1) Use masking tape to protect painted panel from accidental damage while drilling holes. 2) Use nyloc nuts to secure modules to the chassis. If nyloc nuts are not available use thread-lock blue - Loctite 242 to keep nuts from backing off 3) Always use a wire hook to connect a wire to eyelet :( Do not rely on solder to provide mechanical support.
Oh right, an amp that the fan sounds louder than the music, marvellous.
@joshpoe
2 жыл бұрын
You've never built a solid state amplifier that's obvious. People like you should start with a high voltage vacuum tube amp. Do zero research, maybe you won't live through it.
@dougieroberts7045
2 жыл бұрын
@@joshpoe Thanks for the advice, appreciated, I will save myself some money and buy something that sounds half decent instead.
@joshpoe
2 жыл бұрын
@@dougieroberts7045 before you judge maybe you should understand what speakers are being used and how this was recorded. I've listened to 1 million dollar Krell and Mark Levinson systems generating thousands of watts but for musicality I've been more blown away by analog systems running off batteries making less than 50 watts.
@ConorNoakes
2 жыл бұрын
That’s fairly average by PA amplifier standards…
@Tremodua
2 жыл бұрын
@@joshpoe This amplifier is not so powerful to run fans on idle or low load. My Yamaha amplifier turns on fans only on high load. And good amplifier has to have balanced inputs.
Build a High Power Amplifier - MICRO BOOSTRAP with XTI-2000 BOX: kzread.info/dash/bejne/jKN22tyzmLK3g7Q.html
OMG! The two loud cooling fans adds to the music.
ha, i saw what you did with the speakon, mounting holes where drilled in mirror, so you needed self tapping screws :) instead of the normal M3 bolts Nice work, would have chosen a heavier transformer though.
Sangat kreatip sangat rapi seperti power pabrikan,sangat bangga ada orang sulsel bisa begini😊
@cbzproject
2 жыл бұрын
Thengkyu👌
@uwok1081
2 жыл бұрын
@@cbzproject itu dijual nda bang
@john_smart7212
2 жыл бұрын
@@cbzproject di jual berapa bang
Beautiful work. Thanks for this.
Very good looks so professional 👏👏👏👏🇵🇭
@cbzproject
2 жыл бұрын
Thanks
Very cool, great work! 😁
Great video 👍🏻 Back room amp, not a fan of fans in amplifiers.
joss tenan ki power balap
Kerjanya kemas👍👍
Well built👍👍nice looking amp
Hi... amazing work But do you have a component list and a tutorial on how to build the board off the pcb??? For the amp section
Nice build... But the amplifier looks underpowered with that transformer
Nice looking amp. I'm a bit worried about lack of protection. I didn't see any fuse on that transformer. Also there should be some inductance to remove noise from line. I also didn't see any fuse on other side of that transformer. But who knows maybe there was some. Anyway. I would suggest to add steel plate from both sides so actual amplifier is shielded from transformer .It might help a little to remove the hum/noise.
@alexandrefournier-ahizoune8098
2 жыл бұрын
the fuse is located in the ac connector socket @4:52
@Daaremikkel
2 жыл бұрын
There is a fuse on the power inlet. A noise filer would have been nice, but there is no switchmode stuff and a lot of capacity, so I am sure it is fine.
@SylwerDragon
2 жыл бұрын
@@Daaremikkel yes Sorry i did miss that. I'm glad for that also i'm glad for that second fuse on secondary. As you said some filtering would be nice and i'm not sure how effective it would be but i expect it will loose efficiency once higher power will come into play..but still it might be good idea to test it. Could you please make simple check ..Bring proper laboratory 6.5 digit meter and test AC voltage at the input of your power stage..I know you can't check all frequencies only line .but still this might show you how much AC you have in your amplifier..I would also suggest to check it with some load..lets say 400Hz on input with full power and then check it again..
@expired56k
2 жыл бұрын
@@SylwerDragon That and adding speaker protection would be a great idea especially given plenty of room inside the chassis. Overall, I think for the advertised budget it's a pretty solid build. Speaker protection would have only added maybe $10-15. At least in this build amp heatsinks are properly installed in line with fan airflow, seen so many in these DIY videos that are installed perpendicular to the airflow.
@anwarbudiono8621
2 жыл бұрын
Makasih atas ilmunya
Mantap Mirip built up mas salam dari jateng kab.pemalang hadir terus tapi jarang komen
@cbzproject
2 жыл бұрын
Sipp👌
where did you get the amps from? can't find them anywhere .. would be nice if you included that information thanks
Mantap mas bro.. 👏👍
@cbzproject
2 жыл бұрын
Thanks
@ty-qw6kt
2 жыл бұрын
Orang indo Dengan gaya
High power amplifier using 40 transistors. Video link👇👇 kzread.info/dash/bejne/apeA0ZNpqJDFiso.html
@girlanecunha972
2 жыл бұрын
Compra
@john_smart7212
2 жыл бұрын
Kalo pesen lewat mana bang
@jeevanwaghela8285
2 жыл бұрын
@@girlanecunha972 CBZ.projackt.kaha.milte.hai.thoda.bata.sakte.hai.ple
Elahhh beli ajaaaa yg pake tabung juga adaa... Udah dolby atmos pulak.... Optical cable to speaker pake velodine
Quality build👍
thank you sir useful video
Mantap jga yg ini mas.
Terima kasih sharing vidionya..
Nice power sound system
Super clearty good job sir ❤
Mantap boss👍👍
Transformer needs to be 10 amp at least for utilizing those transistors at full power output. otherwise nice build.
Wow amazing
Aku suka karia-kariamu brow👍👍
@cbzproject
2 жыл бұрын
Sipp👌
Sama punya ku 5@ tpi trfonya murni 45 tpi mau ganti yang gede 10@ tau 15@ biar tambah power. Tpi aq salut n bangga dengan hasil nya rapi dan oke punya
@cbzproject
2 жыл бұрын
Thanks
merk trafo ditutup, tp coba saya tebak.. pasti merknya Beii.. 😆 oh ya, sekali kali backsound ny pake tarling mas, biar mantep.. 😀
Micro boostrap mantap..
Invest a couple bucks in an automatic center punch, it will make drilling accurately a lot easier.
Good Job .... super like amigo..
Nunggu offlinenya. Akhirnya bisa di dwonload . Wkwkwk
Excelente proyecto, buen sonido Felicitaciones
Mantap 😀
Jos jos tanks Konten kek gini gua like
@cbzproject
2 жыл бұрын
Sipp👌
loved it
Wow nice amp
Hadir bosku, salam dari sulawesi tenggara
@cbzproject
2 жыл бұрын
Sipp👌
Beautiful work and slowdown your video im a beginner in electronics bro
nice work
Muito bom. Da hora.parabens . Eu compraria. Só falta colocar mais LED . Na frente.
Mantap👍
Do you have a parts list and vendor information beyond the proto circuit board house? Or are you selling plans?
Behtarin luk👍👍👍👍👍
Is very good 👍👍
Im from indonesia i love sulawesi 🙏
what are the possibilities of putting in a bass and treble control?
I love the work you do!! 👌 Would it possible in the future if you can get a good set of speakers with tweeters too? I'd love to hear how your amps perform in the upper frequencies.
@narmale
2 жыл бұрын
lolol imagine judging audio quality of components over a sampled and encrypted data stream on youtube...
@iceman45ification1
2 жыл бұрын
@@narmale and I'm supposed to care about that?
@narmale
2 жыл бұрын
@@iceman45ification1 well its obvious you dont 🤣🤣
@iceman45ification1
2 жыл бұрын
@@narmale you do realize that people that laugh at their own comments is a sign of mental issues? You definitely made that obvious.
@narmale
2 жыл бұрын
@@iceman45ification1 haha, well i did get 37/36 on a psychologist test for a psychopathic tendency questionnaire... but id rather laugh at jokes then be a karen like most people sour with life and age, they typically just end up fat, bald, jowled, bitter and hatefull of everyone around them.
I really like this video
@cbzproject
2 жыл бұрын
Thanks
Bikin produk masal saja bang, dijual dipasaran pasti banyak peminatnya bang👍
Semoga kit utk panel depan dan belakangnya cpat d upload d shopee salam dari bone bos
Bro... Why did you zip tie audio, power and mains power cables together? That single step blew your insulation rating AND made it more sensitive to noise and interference. Also using black for earth? You took 4 premade components, put it in a box and screwed up the wiring. That was a 16 minute video. Nice.
@AkkerKid
2 жыл бұрын
None of the wires soldered went through the loops. No vibration mitigation on the solder joints. Fans blow back to front and are powered by wires parallel the audio signal. Eventual galvanic corrosion between steel and aluminum due to lack of isolation. Undersized transformer. No fuses beyond the C15 power jack. Binding posts are INPUTS?!!? I'm guessing this guy is FRESH out of school. Make a few PCBs and now you think you know everyhing.
@dexcronicle9813
2 жыл бұрын
@@AkkerKid mohon buatkan saya video yang benar tentang ini,saya sangat membutuhkan dari seorang profesional seperti anda...mohon
@dexcronicle9813
2 жыл бұрын
@@AkkerKid mohon buatkan saya video yang benar tentang ini,saya sangat membutuhkan dari seorang profesional seperti anda...mohon
@AkkerKid
2 жыл бұрын
@@dexcronicle9813 Sorry brother, I don't have need to build one of these. If you plan on building your own, keep in mind a few requirements. Keep high power and low power signals separate so you don't introduce noise. Make sure your weakest components are fuses so they break first before anything else. Consider gluing down large components like power capacitors so they don't break off of your PCBs.
I love it
Joss mase...
Never rely on a soft soldered joint for mechanical strength. The holes in the transformer tabs are there for a reason, you're meant to hook a wire through each and make the joint so the end of the wire is evident. See 11:40 into the video for what I'm typing about. With the transformer connected as shown you'll get around +/- 21 V DC, hardly a high powered amplifier - maybe this is an advertisement for the PCB manufacturer that you get paid for.
@wraiths_
Жыл бұрын
I know its been months, but I believe that is a particualr brand of transformer prevalent in Indonesia which has multiple outputs. Usually it has support for preamp 12-0-12 or 15-0-15 located at the bottom while on the other side has the higher output usually 28 to 55 volts
Congratulations 👏
what kit is this and what features has it? output power ....price brand and so on
좋은영상 잘보고갑니다.... 이런것도 가능한가요? 파워 앰프를 인티로 만들어서 마이크도 되고 베이스볼륨과 고음볼륨도되고 셀럭터 스윗치도 달아서 외부입력 1,2,3, 그리고 가능하면 레코드 입력도 되고 전면에는 두개의 아날로구 출력메타를 크게두개 달아서 입체감을주고 PA앰프도 되지만 오디오용으로도 될수있는 멋진앰프도 가능한지 물어봅니다!^^ 그리고 펜소리가 안들릴정도로 조용해야됩니다...
josss masszeh
Mantap ada logo dri pulau sulawesi
nice one sir youre greath and excellent work job.sending my full support of youre compony.god bless.😇😊🙏❤
Jakut hadir broo
Mantapp masss
@cbzproject
2 жыл бұрын
Sipp👌
Very good
Awesome bro, nice work. Where are you from???
@ermawati_channel
2 жыл бұрын
Indonesian 🇮🇩
NEIGHBORS LOVE IT
Nice
Untuk older siap pakai srti itu lewat apa bang..?
GOOD WORK BUT HOW MUCH DID IT ALL COST AND HOW MUCH RMS IS IT KICKING OUT
Kren jos kak Taiwan hadir
@cbzproject
2 жыл бұрын
Sipp👌
kirain org barat njir, pas lihat pcb kok pulau sulawesi trnyata org indo, mantab
Veri good
สุดยอดเยี่ยม
Keren kerjanyah rapih
good project sir nice video how much watts ka amplifier boards used?
Very very nice
How much does the power cost bro
Super super super 👌
Nice❤👋
Me puede compartir gerber de las salidas a bocinas??
Perfect!!!
a powerful amplifier with a radiators located UNDER the amplifier boards, with no air inlets in the bottom of the housing; probably only for use WITHOUT the housing...?
@jlinkels
2 жыл бұрын
it is not very relevant. The amount of air blown by the fans is way larger than the amount of convected air. If it is a sound design when listening to low level music is a different issue. I don't believe in power cooling by default.
Gan coba buat power/amplifier buat horn toa 🙏🙏
Such type of videos are only assembly. Nothing about actual circuit design. Btw good effort
Joooosss mas..
next bikin power 500 watt untuk class indoor gan ....4 channel
Keerrreeen bosku
@cbzproject
2 жыл бұрын
Sipp👌
Your video is very good but where to buy this amplifier why you don't know please enter the link
nice
klo pesan dah jadi sprti itu harga brp mas,,pakai trafo ERA 5@ 45 ct
bersih rapih . transformer era ya ?
I'm here again, do you have diagram of the amplifier? Thanks from Venezuela.
Mantap
@cbzproject
2 жыл бұрын
Sipp