Build A Cheap DIY Anvil Stand For The Vevor 130lb Anvil
Тәжірибелік нұсқаулар және стиль
This video is NOT sponsored. The links below are affiliate links. Which means if you use these links to make a purchase we will receive a small commission.
Link to Vevor Belt Grinder:
www.vevor.com/belt-grinder-c_...
Link to 132Lb Anvil
www.vevor.com/cast-steel-anvi...
Please LIKE SUBSCRIBE SHARE COMMENT and Click the BELL
lol I know that's a lot. It really helps small channels more than you would expect.
Thank you so much for watching.
In this video I build an Anvil stand with 4 by 4s, wood glue. screws, bolts, and some 1/8 in by 1 inch steel strips.
I glued the wood together and screwed each 4 by 4 to each other. Then I wrapped the steel bands around the whole thing and bolted it in place. I also Etched my logo into a shield that I cut out of a scrap piece of metal.
This stand was built for a 130lb Anvil from Vevor.
If you have any questions about this build please let me know in the comments/
Thanks
#vevor
#anvil
#bladesmith
#blacksmith
#knifemaking
@TyrellKnifeworks Is where I learned about this Anvil.
@vevor.official
Пікірлер: 27
Great job on the video Drew! Thanks for making it.
@drewdoesart9277
Жыл бұрын
No Problem. Thank you for watching. I really appreciate it.
Thank you for the great review! We’re so happy you loved your experience and can’t wait to have you back in the future.
@drewdoesart9277
Жыл бұрын
Absolutely. I also just got the Vevor 2 By 82 Belt Grinder. Very nice machine. I look forward to adding more of your tools to the shop. Thank you for the comment.
Amazing video!
@drewdoesart9277
Жыл бұрын
Thanks man. I appreciate that.
This is awesome.
@drewdoesart9277
Жыл бұрын
Thanks man. I really appreciate it.
This looks like you just went and plucked this out of Valhalla weekly this thing looks super sturdy and tough good work man keep it up
That is so cool.
@drewdoesart9277
Жыл бұрын
Than you
i'm just as curious as to how you made that sweet shield logo!!
@drewdoesart9277
5 ай бұрын
I think I did a short where I show how I did it. But I did do videos on how I etch. I used Automotive pinstriping around the perimeter and I printed out my logo with the cricket cutter. Then I etched it in salt, water, and used D.C. electricity.
Awesome video bud! Love this stand
@drewdoesart9277
Жыл бұрын
Thank you. I appreciate it.
How is this thing held together on the inner timbers though?
@drewdoesart9277
Жыл бұрын
I screwed each board to each other. Once you have the 1st row done, then you screw 1 on at a time and glue it. I used 3 1/2'' construction screws. I went in at an angle in both directions. The outside corners I only put screws under where the bands go. It's really solid. It's still nice and tight.
That's the most awesome anvil stand I have ever seen.
@drewdoesart9277
Жыл бұрын
LOL Thank Brother ; )
@drewdoesart9277 what did you coat the wood with?
@drewdoesart9277
2 ай бұрын
I just used Boiled Linseed Oil. I sanded the wood to 80 grit with a palm sander first.
@nucah7880
2 ай бұрын
@@drewdoesart9277 thanks! I figured boiled linseed oil but wasn't sure. Appreciate it. I recently purchased an anvil and love this type of setup!
@drewdoesart9277
2 ай бұрын
@@nucah7880 Thank you. I just did another anvil stand that's a little smaller but still the same construction. kzread.info/dash/bejne/oouVy8yzYs6_n84.html
@nucah7880
2 ай бұрын
@@drewdoesart9277 sweet, I'll check that out. Thanks!
Man! That’s just bad A$$
@drewdoesart9277
Жыл бұрын
Thanks man. I appreciate it.