Buckling Analysis of Composite Plates Ansys ACP Tutorial (Theory and Calculations are Explained)
Buckling Analysis of Composite Plates tutorial by ANSYS 2020. Theory and the analytical calculations are shown.
Linkedin: / meriç-büyükkoyuncu-10b...
Buckling Analysis of Composite Plates tutorial by ANSYS 2020. Theory and the analytical calculations are shown.
Linkedin: / meriç-büyükkoyuncu-10b...
Пікірлер: 34
hey guys, FYI the analysis done here is LINEAR buckling analysis. still very informative and the best analysis explanation on KZread!.
Teshekkur ederim, Meric bey. Cok yardimci bir video
I needed this. Thank you very much 👏🏽
@mericbuyukkoyuncu385
3 жыл бұрын
Thank you so much
i so much appreciate all your analysis. Thanks, you are outstanding. waiting patiently when you will drop sandwich panel.
@mericbuyukkoyuncu385
3 жыл бұрын
Thank you! It will be released soon.
As usual. Salute.
@mericbuyukkoyuncu385
3 жыл бұрын
Thank you
Thank you for the tutorial sir. Can you please do an analysis on hybrid composite material with user defined material
Good tutorial on buckling..!!
@mericbuyukkoyuncu385
3 жыл бұрын
Thank you
sir please could you do more videos on testing of composite plates in Ansys such as Torsion test , Shear , Fatigue , Thermal , Fracture (crack) , Impact and how to model composite shaft in Ansys
Hocam iyi akşamlar. Öncelikle elinize sağlık çok güzel bir tutorial olmuş. Burada kompozit plakayı kurarken bottom shell olarak modellediğinizi fark ettim, bu model sonucunda elde ettiğiniz sonuçlar ile teorik kısımdan gelen sonuçlar birbirini tutmaktadır ancak modeli mid shell olarak kurmamız daha mantıklı olmaz mı (uyguladığımız kuvvet doğrultusunda parçada ekstradan bir eğilme momenti oluşmasını engellemek için)? Buna ek bir sorum daha olacaktı, üzerinde çalıştığım bir konu için parçada eğilme momenti oluşmamasını istiyorum(sadece basmadan kaynaklı deformationı ölçek için) bu sebepten dolayı modeli mid shell olarak kuruyorum fakat mid shell olarak kurduğum modele buckling analizi yaptığımda teorik olarak elde ettiğim sonuçtan daha farklı bir analiz sonucu almaktayım bunun sebebi hakkında yardımcı olabilirseniz çok sevinirim.
Thank you so much for these tutorials ,but I've afford. may you make tutorials about curved plate?
Please do more videos on Failure Analysis of Composite material plates using Ansys
Hi Meric, Thanks a lot for the informative video. Can you please tell me the source of the analytical equation? Which paper or book did you get it from?
good tutorial . Please can you the tutorial about lateral torsional buckling
@mericbuyukkoyuncu385
3 жыл бұрын
Thank you, I will check this topic
Good morning, Can you upload some lectures on MATLAB?..It will be very helpful
Sir, I request to model a Fiber metal laminate pressure vessel. i.e. inner metal liner surrounded by external FRP layer pressure vessel. Thank you.
Hocam Iyi aksamlar, Kompozit Sandvic bir panelin buckling analizini yapmaktayim. Mode u 1 olarak sectigimde 3 tepe noktasi cikmakta. Bunun sebebini anlamakta zorlaniyorum mode 1 olunca neden tek tepe noktali bir burkulma davranisi gostermiyor malzememiz.
@mericbuyukkoyuncu385
3 жыл бұрын
Selamlar, Analizde mode 1 olarak en düşük load factorlu case gösterilir. Load factorun en düşük çıktığı case sizin kritik burkulma kuvvetiniz ve o mod ise mode 1 sayılır.
Good morning sir, I request to analyse a composite plate with metal liner.
Hocam selamlar. Öncelikle elinize sağlık çok güzel bir tutorial olmuş. Burada slaytlarda kullandığınız formülasyonun çıkarımını bulabileceğim bir kaynak önerebilir misiniz?
@mericbuyukkoyuncu385
3 жыл бұрын
Merhaba, Çok teşekkür ederim yorumlarınız için. Formulasyonun olduğu kitaba aşağıdaki linkten ulaşabilirsiniz. www.springer.com/gp/book/9781402031106
@yusufsahiner85
3 жыл бұрын
@@mericbuyukkoyuncu385 Teşekkürler.
whats the name of research paper you mentioned in video
Hi sir, can you conform loadfactor formula with reference.
can you please provide the source of your input data you took or any research paper ?
@mericbuyukkoyuncu385
3 жыл бұрын
Input material data is created randomly. It does not matter, you can crate too. There are formulas which provide the solution for all input data. If you change the input data, you need to calculate your outputs according to the input data. By the way, all the formulas are taken from this book : www.springer.com/gp/book/9781402031106
D1 D2 D3? what are these terms and How to determine these values
@mericbuyukkoyuncu385
2 жыл бұрын
Check my other videos
HI BROTHER >>> i am Iraqi engineer ....can u send to me design guide for dimensions of fiberglass ...and the standard dimension for cross section area for chanel made of fiberglass
Barga Mahtal! (Sakha. Turk) [Thank you very mach!)