BT50 / Ranger P00BD Mass Air Flow Circuit Range / Performance - Flow Too High - Found & Fixed - DIY

Автокөліктер мен көлік құралдары

Mazda BT50 Turbo Diesel with engine warning light on making whooshing noise when accelerating - hissing noise under load - possibly going into limp home mode (depending on part failure)
If you have an issue like this one, then following these simply checks will allow you to diagnose the fault 100%
Fault code P00BD Mass Air Flow Circuit Range / Performance - Flow Too High -
If I helped ya out? or just enjoy the content & you would like to buy me a drink ko-fi.com/gerardburke
Thanks to everyone who watches and likes my videos, I appreciate you all so much.
Tool options that I recommend and use - www.amazon.co.uk/shop/gerardb...
➢ For business inquiries Email : gerardburkebusinessinquiries@gmail.com
Disclaimer:
GerardBurke is a qualified motor technician who has completed modules & courses in manual handling and all aspects of workshop safety. These videos are not intended to be used by anyone who is not trained and or qualified to carry them out.
Due to factors beyond the control of GerardBurke, I cannot guarantee against improper use or unauthorized modifications of this information. GerardBurke assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. GerardBurke recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of GerardBurke, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not GerardBurke.

rushing air sound when accelerating
car sounds like a vacuum when accelerating
hissing noise from car when accelerating
hissing sound when accelerating ford
Ford Ranger
Mazda BT 50
#MazdaBT50 #FordRanger #P00BD

Пікірлер: 30

  • @MrFunkyBeatz
    @MrFunkyBeatz2 жыл бұрын

    Thanks man you helped me find my problem. So I used epoxy resin / araldite and some lay flat hose and gaffa tape and sealed the hole until the plazmaman pipe turns up.

  • @MiracleMAX
    @MiracleMAX3 жыл бұрын

    It's great to sometimes get an easy diagnosis - it makes your day a whole lot better! Well done. 😉

  • @GerardBurkeBurkesGarage

    @GerardBurkeBurkesGarage

    3 жыл бұрын

    Yep, it's nice from time to time to have a fast fix ⌚😉 Makes everyone happy 😁

  • @bonganimthombotithelifethe7913
    @bonganimthombotithelifethe7913 Жыл бұрын

    You really helped and saved me so much confusion, thank you and keep sharing with us.

  • @bigsteve8253
    @bigsteve82532 жыл бұрын

    having that same code on my 2012 Ranger, very helpful vid, cheers mate

  • @rickyvella93
    @rickyvella932 ай бұрын

    Thank you, i got a P006A code today and while researching that came across this video. I also have had a strange whistling noise when accelerating for the last couple of months. I took it to a mechanic and they said they couldn’t find any issues. I will check for a split hose and see if this is the issue for the whistle noise.

  • @romanosautomotive
    @romanosautomotive3 жыл бұрын

    Excellent Gerard. We should just have these hoses in stock! :)

  • @GerardBurkeBurkesGarage

    @GerardBurkeBurkesGarage

    3 жыл бұрын

    Cheers Rob, sounds like a good idea mate 🤔😀😂

  • @lucianh2914
    @lucianh291413 күн бұрын

    I have the same problem on mazda 5 1,6 diesel and i don't find the air flow fuite.I changed the vanne EGR,AIR FLOW debimeter,and it don't work.Thanks.From France

  • @Liamautomechanic
    @Liamautomechanic3 жыл бұрын

    Good vid gearld.

  • @GerardBurkeBurkesGarage

    @GerardBurkeBurkesGarage

    3 жыл бұрын

    Thanks Liam 🙏

  • @patkelly7999
    @patkelly79993 жыл бұрын

    Good job Gerard:):)

  • @GerardBurkeBurkesGarage

    @GerardBurkeBurkesGarage

    3 жыл бұрын

    Thanks Pat 🙏🙏 Hope you're enjoying the sun over there ☀️😎🌞

  • @patkelly7999

    @patkelly7999

    3 жыл бұрын

    @@GerardBurkeBurkesGarage Yes, it was nice while it lasted, back to rain again Gerard 👍😎🌧️🙏🇭🇲🇮🇪

  • @lowcalibre837
    @lowcalibre837 Жыл бұрын

    Have the same code come up, goes into limp mode, top hose is aluminium and is not split, checked intercooler but can't find anything wrong with it, haven't tried to pressurise it, all hose clamps were tight, any other ideas i can try.... ??

  • @petermarx4

    @petermarx4

    7 ай бұрын

    Hey mate did you find out what it was?

  • @mikejilili6866
    @mikejilili68662 жыл бұрын

    I am using ford ranger 3.2 i was hearing the same sound and found out the horse is damaged like in the video. THANX SO MUCH... however i changed the pipe but i can still hear the whooping sound on acceleration!! What can be the problem? Or there are error code to clear first!?

  • @bongab26

    @bongab26

    2 жыл бұрын

    I have same issue on my Mazda 2.2 changed the split pipe but the noise n power train warning light comes back occasionally

  • @demyshka
    @demyshka Жыл бұрын

    Hi, where you located in UK, I bought Focus 2005 2 litre, could you help me with my car

  • @keithsmith855
    @keithsmith8553 жыл бұрын

    My m.f.a.c on my ford focus 2003 automatic Was changed but it caused the gearbox to only change in to 3 of 4 gears. Now the ! With a warning orange circle around it comes on and won't change into 4th same problem different light?? Any ideas it's a train of a car 250,000miles + and this is only thing that has happened since owned 10 + years ago looks mint to????? Thanks mate

  • @GerardBurkeBurkesGarage

    @GerardBurkeBurkesGarage

    3 жыл бұрын

    Hello Keith, There is a reason I don't do any phone diagnosing or online because of the many possibilities that surround vehicle faults. It is difficult enough to diagnose problems in the workshop with all my senses and professional tools at my disposal. This is certainly the case with yours, you will need to bring it to a recommended repairer to assess the inputs and try and narrow down the fault to electrical or mechanical. Scan code reading, live data assessment, component testing, connection/wiring checks, shift solenoids or other transmission internal failure. For anyone trying to figure it out through guessing without testing then it would be best to try and find the exact symptoms on forums or the likes.

  • @keithsmith855

    @keithsmith855

    3 жыл бұрын

    @@GerardBurkeBurkesGarage hahaha worth a try as I was the first to like the video I thought you might answer then I looked at the 56k+ subs ! And realised not a chance sorry bud my apologies, I've done all that you suggested and no fault code has been found on this occasion but I really appreciate your reply all the same sincere apologies again , Thanks Mr Burke .👌🏼

  • @GerardBurkeBurkesGarage

    @GerardBurkeBurkesGarage

    3 жыл бұрын

    👌👍

  • @MrKongla17
    @MrKongla17 Жыл бұрын

    Please guide me out of this problem.

  • @wellingtonafa6714
    @wellingtonafa6714 Жыл бұрын

    Normally what's the price fixing that problem please

  • @MrKongla17
    @MrKongla17 Жыл бұрын

    Including intake manifold

  • @MrKongla17
    @MrKongla17 Жыл бұрын

    I change its all about intercooler however CodePO0BD still exist

  • @TheObSeRvErTheObSeRv

    @TheObSeRvErTheObSeRv

    Жыл бұрын

    Intake manifold leak Mass Air Flow (MAF) sensor failure Powertrain Control Module (PCM) failure Wiring issue

  • @castrolgtx5064
    @castrolgtx50643 жыл бұрын

    Common Land Rover Discovery and Range Rover problem

  • @GerardBurkeBurkesGarage

    @GerardBurkeBurkesGarage

    3 жыл бұрын

    Spot on Eric 👌👍

Келесі